Expert Service 1-877-289-7664 [Hours]

Amp up your factory system with quality car amplifiers. Find a large selection of monoblock amps including Class D, mini amps, micro amps and other car amps for subwoofers. Shop now!
Narrow Your Results

Your Filters

Clear All
Amplifier Class
Total RMS Power Output

I'm sorry, no available results!

Price range:
$94.99 $549.95

Number of Channels:

Minimum Impedance Unbridged:

Minimum Impedance Bridged:

Bass/Gain Remote:

Sonic Certified Amplifier:

Preamp Outputs:

Speaker Level Inputs:

CEA-2006 Compliant:

Maximum Input Gauge Size:

3400W Max, Riot Series Class D Monoblock Car Amplifier

• RMS: 1050W x 1 @ 4 ohms
• Total Peak Power: 3400W x 1 @ 1 ohm
• Wired Remote Bass Level Control Included
• Dimensions: 13-1/2"W x 10-7/16"D x 2-1/4"H



(2) RE Audio SEXv2-12D4 12" SE-X v2 Series Dual 4 ohm Subwoofer + Hifonics HFi1500D 1500W RMS Class D Monoblock HFi Series Amplifier

• 1 ohms: 1500 watts x 1 chan.
• Rubatek Foam Surround
• Dual Composite 2-Piece Cone
• Tork-Tite Terminals
• Progressive Spiders
• Double Stacked Magnets
• Wired remote bass level control included
• Preamp RCA outputs to daisy chain multiple amps
• 3-way protection circuitry (thermal, overload, and speaker short protection)
• Dual speaker terminals simplify the hookup of multiple speakers
• Signal to Noise Ration: >95 dB



1200W Monoblock Tarantula NANO Series Class-D Amplifier

• RMS Power: 660W x 1 @ 4 ohms, 1050W x 1 @ 2 ohms, 1200W x 1 @ 1 ohm
• Three-Way Protection Circuitry
• Low Pass Filter
• Dimensions: 6.75" W x 12.75" L x 1.75" H



1100W RMS Monoblock Class D X-Power Series Car Amplifier

• RMS: 650W x 1 @ 4 ohms, 1100W x 1 @ 2 ohms
• Total RMS Power: 1100W
• CEA-2006 Compliant
• Bass Boost: 0-12 dB at 50 Hz
• Multi-Stage Power Management Circuit
• Dimensions: 9"L x 13-3/8"W x 2-1/4"H



2800W Max Nano Block Series Monoblock Class D Amplifier

• RMS: 450W x 1 @ 4 ohms, 700W x 1 @ 2 ohms, 1400W x 1 @ 1 ohm
• Total Peak Power: 2800W
• CEA-2006 Compliant
• Selectable Bass Boost: 0, +6, +12 dB
• Class D Circuitry
• Dimensions: 10-5/16"L x 5-1/2"W x 2-1/8"H



1200W RMS, PDX Series Monoblock Power Density Class D Digital Car Amplifier

• RMS: 1200W x 1 @ 4 ohms, 1200W x 1 @ 2 ohms
• Total RMS Power: 1200W
• CEA-2006 Compliant
• 6-Layer Glass Epoxy PC Board and Compact Size
• Thermal Protection Circuitry
• Dimensions: 7-9/16"D x 10-1/8"W x 2"H



Related Categories

Amplifier Wiring Kits
Get all the cables, wires, and hardware you need to install your new car audio amplifier with one of these power amp kits. Amplifier wiring kits come with your basic power and ground cables, as well as other necessary wires. Select complete amplifier kits will include speaker wire, RCA interconnect cables, and more! To make sure you get the kit that is best designed for your car audio system, scroll down to the bottom of this page for the buying guide.
Car audio capacitors are a great addition to any aftermarket audio system that is in need of a little extra power. Capacitors store a temporary electrical charge that can be released during periods of extra power strain. If a vehicle has dimming headlights when music is played, a capacitor could solve that problem.
Sound Processors
For those who want the most out their car audio system, a quality sound processor is a must. After some slight adjustments, your systems will sound like it has been professionally tuned and optimized. Tune your system to perfection with these crossovers, equalizers, and bass drivers. Click here to learn more about digital sound processors and to find out which type would be best for your car audio system.

Monoblock Amplifiers Information

Mono Subwoofer Amplifiers

Mono amplifiers are single channel amps, but they can be used to power more than one subwoofer. Mono amps typically produce more power than multi-channel amps, which makes them ideal for powering subwoofers. Class D mono amps are the most efficient of all amplifier designs because they draw less current and as a result generate less heat in comparison to the classic mono amplifier design.

A mono amplifier puts out only one channel of sound, as opposed to a stereo amp that puts out two channels of sound. A mono amp is generally used for extremely low frequencies, such as bass, that are channeled into a single subwoofer. It doesn't matter that both stereo channels are combined for these low bass frequencies because you couldn't tell which channel the sounds are coming from anyway because you feel the sound pressure more than hear the sound.