Expert Service 1-661-257-9993 [Hours]

Infinity Reference 1220se + Hifonics ZRX1216.1D Loaded Amplified Subwoofer Bass Bundle w/ Wiring Kit

List price $689.97 1200 Watt Single 12" Reference Series, Ported Loaded Enclosure + Hifonics Monoblock Class D Amplifier + Belva BAK42BL Wiring Kit

Discontinued
|

We apologize

This item has been discontinued

Item Added to Cart

Infinity Reference 1220se + Hifonics ZRX1216.1D Loaded Amplified Subwoofer Bass Bundle w/ Wiring Kit

List price $689.97 1200 Watt Single 12" Reference Series, Ported Loaded Enclosure + Hifonics Monoblock Class D Amplifier + Belva BAK42BL Wiring Kit

$249.42

Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
$26.99
Add Warranty
3 years of protection

XS Power XP750 Special Edition

12-Volt Deep Cycle AGM Power Cell with 750 Max Amps

$72.99

Add
40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

$97.99

Add
Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Infinity Reference 1220se + Hifonics ZRX1216.1D Loaded Amplified Subwoofer Bass Bundle w/ Wiring Kit.

Get FAST answers from customers ASK a Question See questions answers

Infinity Reference 1220se


Infinity Reference 1220se (REF1220SE)

1200 Watt Single 12" Reference Series, Ported Loaded Subwoofer Box/Enclosure with Slipstream Port and LED Illumination
Quantity: 1

General Features

  • Single12" Reference Series, Ported Loaded Subwoofer Enclosure
  • Power Handling:
    • Peak: 1200 watts
    • RMS: 300 watts
  • Recommended power range: 100 - 300 watts RMS
  • Nominal Impedance: 2 ohms
  • Pre-loaded with an Infinity Reference 1252W
  • Light-blue LED illumination, with Remote Turn-On connection
    Installation Note: Requires a 12v Source. (e.g. Trunk Light)
  • Vented motor assembly
  • Polypropylene cone woofer
  • Large-roll butyl rubber surround
  • Bumped backplate
  • Vented pole piece
  • Progressive spider
  • Low resonance enclosure
  • Up-firing ported design
  • Slipstream port for reduced distortion and clean bass
  • High output enclosure for lower frequency response
  • Silver front beauty plate with pre-installed grill
  • Automotive-carpet wrapped enclosure
  • Nickel-plate binding post for best connection possible
  • Sensitivity: 94dB
  • Frequency Response: 33Hz - 300Hz
  • Dimensions: 17-1/8" L x 21-1/16" W x 16-5/16" H
  • Authorized Internet Dealer
  • 3-year Manufacturer's warranty (Subwoofer Only)

Hifonics ZRX1216.1D

1200W Monoblock Zeus Series Class D Amplifier
Quantity: 1

General Features:

  • Zeus Series Monoblock Class D Car Amplifier
  • Max Power Rating:
    • 4 ohms: 400 watts x 1 chan.
    • 2 ohms: 600 watts x 1 chan.
    • 1 ohm: 1200 watts x 1 chan.
  • Max power output: 1200 watts
  • Wired remote bass level control included
  • Variable Bass Boost (0 to +12 dB bass boost at 45 Hz)
  • Mono channel operation
  • Variable low-pass filter (40-300 Hz, 24 dB/octave)
  • Frequency Response: 10-300 Hz
  • Old School Hifonics heatsink provides superior heat dissipation
  • Military grade PCB construction
  • Simpatico coil design
  • Hifonics surface mount design
  • DC, short circuit, thermal and overload protection
  • 4 gauge power and ground wiring is required for installation
  • Dimensions: 10"W x 12.6"L x 2.4"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Belva BAK42BL (Blue)

Primary Color: Blue - Complete 4 Gauge Amplifier Wiring Kit with 2-Channel RCA Cable (CCA Wiring)
Quantity: 1

General Features:

  • Complete 4 Gauge 2-Channel Amplifier Installation Kit
  • Designed specifically for car audio systems up to 1000 watts RMS
  • Premium Powerflex power and ground wire provides optimal power transfer
  • Made from Copper-Clad Aluminum for a pure uninterrupted transfer of power and signal
    • Belva CCA wire is made from 30% copper while other CCA wire is just 10% copper
  • Helical Twist Construction Audio Interconnect RCA cables minimize noise and interference
  • In-line Mini-ANL Fuse holder with a 80 amp Mini-ANL fuse offers ideal protection for high powered systems
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Kit includes:

  1. 17 ft. (5.2 meters) Blue 4 gauge power wire
  2. 3 ft. (.91 meters) Black 4 gauge ground wire
  3. 17 ft. (5.2 meters) Gray 18 gauge remote lead wire
  4. 17 ft. (5.2 meters) Helical Twist 2-channel RCA interconnect cable
  5. 20 ft. (6.1 meters) Speaker cable
  6. One In-line Mini-ANL Fuse Holder with a 80 amp Mini-ANL fuse
  7. One Black rubber firewall grommet
  8. One 4 Gauge Blue chrome plated ring terminals
  9. One 4 Gauge Black chrome plated ring terminal
  10. Three 18 Gauge Blue Spade terminal
  11. Two 18 Gauge Black Spade terminal
  12. One 18 Gauge Red butt connector
  13. Ten 4" Black zip ties

Amplifier Power Specifications

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

200 watts x 1 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

300 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

415 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

300 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
Not Bridgeable
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

32 - 320 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
98 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
20A x 2 

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
Reference (Infinity)
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
1
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
2 ohms
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
300 watts
Total RMS Power Handling
This is the total RMS power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
300 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1200 watts
Total Peak Power Handling
This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
1200 watts
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Butyl Rubber
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Polypropylene
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
94 dB
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
33 - 300 Hz

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0
Billy H

Cleveland

Verified Purchase
Overall
Durability
Value
Features
Design
Usability
great setup

December 2, 2015

This setup had everything needed for my installer to get it going in my Honda Civic. At only 300watts I wasn't expecting much, and I didn't want much anyway, but WOW what a difference! By no means is this a window vibrating setup, but I get the low end I can't get from my 6.5 coaxials.

0 of 0 found this helpful

Was this review helpful to you?

Accessory Tools and Products

Accessories added

XS Power XP750 Special Edition

12-Volt Deep Cycle AGM Power Cell with 750 Max Amps

Your Price $72.99

40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

Your Price $97.99

Dynamat Sound Dampening Bulk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $159.99

Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

Your Price $94.97

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $34.99

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $69.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $18.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $74.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $7.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

Browse 1 question and 1 answer
Hide answersShow all answers | Sort by
zrx1216.1d does this have high leval inputs?
cameron c on Dec 15, 2015
Best Answer: Hey Cameron,

The amplifier does NOT have high level inputs (see pic below); it will require an LOC to integrate into an OEM setup.

http://www.sonicelectronix.com/pictures_new.php?id=105623&picture_id=2721301
Reply (2) · Report · Rick MStaff on Dec 15, 2015
· Add Answer · I Have This Question Too (0)

Product Summary

Manufacturer

Model Number

REF1220SE_ZRX1216.1D_BAK42BL

UPC

818060014819

Weight

63.32lbs

Internal SKU

ref1220se_zrx12161d_bak42bl

Internal Product ID

105623

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Infinity Reference 1220se + Hifonics ZRX1216.1D Loaded Amplified Subwoofer Bass Bundle w/ Wiring Kit