Expert Service 1-877-289-7664 [Hours]

Memorial Day Clearance

MTX Audio Terminator TN400/4

600W 4-Channel Terminator Series Amplifier

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Authorized MTX 

Dealer
  • Terminator Series 4-Channel Class N Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 45 watts x 4 chan.
    • 2 ohms: 75 watts x 4 chan.
    • Bridged, 4 ohms: 150 watts x 2 chan.
  • Max power output: 150 watts x 4 chan.
  • LED power and protection indicators
  • Gain control
  • Smart engage auto turn-on circuitry
  • Built-in adaptive cooling fans
  • Fixed high-pass filter (85 Hz, 18 dB/octave)
  • Fixed low-pass filter (85 Hz, 18 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 20-200 Hz
  • Dimensions: 13-1/16"L x 10-3/16"W x 2.3"H
  • 4-gauge power and ground leads recommended. Contact us for information regarding a discount on a select amplifier kit when purchased together.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

45 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

75 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

150 watts x 2 channels

Power Specifications - Full Range Channels

Peak Power @ 4 ohms
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Peak Power @ 2 ohms
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Peak Power @ 1 ohm
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Bridged Peak/Max Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the Peak/Max power created once an amplifier is bridged.

Power Specifications - Subwoofer Channel

Peak Power @ 4 ohm
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Peak Power @ 2 ohms
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Peak Power @ 1 ohm
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. However, some manufacture's do not provide an RMS figure and therefore one cannot be advertised.

Amplifier Specifications

Amplifier Series
This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
Terminator (MTX)
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

600 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

300 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
1%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Fixed (85 Hz)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Fixed (85 Hz)
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
78 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
25A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes
Sonic Certified Amplifier
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Amp Bluetooth Connectivity
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
17%
4 Star
67%
3 Star
17%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
3.8
Value
4.3
Features
4.3
Design
3.7
Usability
4.5
John

Edmonds, WA

Overall
Durability
Value
Features
Design
Usability
Great amp! Very powerful!

February 28, 2013

I recently installed this in my Ford Explorer, attached to a Kenwood headunit. It powers 4 Rockford Fosgate speakers with ease. It sounds great and has simple gain adjustments. Highly recommended!! Haven't used it long enough to see if it gets hot or not, but I don't think it will. Works fine with an 8-gauge power wiring.

13 of 20 found this helpful

Was this review helpful to you?

bigboidee

jacksonville, NC

Overall
Durability
Value
Features
Design
Usability
mtx amp

September 4, 2011

Push the Hell out of my 3.5, 5-1/4 and 6x9 that I have it to. Price was outstanding.

9 of 16 found this helpful

Was this review helpful to you?

Nick

Las Vegas, NV

Overall
Durability
Value
Features
Design
Usability
Overheating Problems

August 12, 2011

Was excited about getting this amp, liked the features and was happy about there being a cooling fan on it. Never had a problem with MTX before. BUT... After about a year I can only get about 1-2 songs before the amp overheats. I think this was an obvious design flaw when they built them, and they knew it, so they band-aided it by adding a fan instead of redesigning. Got great sound out of it while it lasted, but not worth the 200 bucks to only last a year.

11 of 21 found this helpful

Was this review helpful to you?

Big Tim

Auburn, NY

Overall
Durability
Value
Features
Design
Usability
Great Amp

January 13, 2011

I've had no problems with this equipment or any MTX products. I'm using monster cable s202-2c-15 for all my speakers. MTX-TDX 4002, MTX-XT693. I love the sound of my music coming from this amp. Need I said more.

10 of 19 found this helpful

Was this review helpful to you?

Josh C.

Birmingham, AL

Overall
Durability
Value
Features
Design
Usability
Solid Choice

December 23, 2014

I got this amp to power my door speakers in my truck. It was running a set of Pioneer 6.5's and pair of 6x9's in my last truck. It's now powering the same size speakers but NVX entry level series in my current truck. It runs them with ease and the spec sheet that came with shows it does more than rated (55 x4 versus stated 45x4) power. The fan is a bit noisy if the volume is low but at normal listening levels it's tuned out.

This is a great value for the price here at Sonic and MTX makes great stuff. I had an old Road Thunder amp in college that lasted years.

4 of 8 found this helpful

Was this review helpful to you?

keith

sunriver, OR

Overall
Durability
Value
Features
Design
Usability
great little amp

August 5, 2010

this is a great little amp for mids and highs

12 of 26 found this helpful

Was this review helpful to you?

Accessory Tools and Products

Accessories added

NVX XKIT84 4-Channel 8-Gauge Wiring Kit

In case you didn't know, NVX has top notch wire and this kit has everything you need!

Your Price $69.99

StreetWires ZN3K-08 8-Gauge Wiring Kit

Get a matching StreetWires amp kit with your new MTX amplifier! Don't forget the RCA's!

Your Price $49.95

Kicker PK8 8-Gauge Wiring Kit

Great wire for your awesome new amp! Don't forget the RCA's!

Your Price $26.95

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $151.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

Small Universal Remote Level Bass Control

The Scosche RLC is a smaller universal bass remote that connects via RCA inputs.

Your Price $11.99

StreetWires FB8

8 Gauge Firewall Bushing

Your Price $6.95

NVX XIV45 4-Channel RCA Audio Interconnect Cable

5 Meters (16.4 ft.) 4-Channel RCA Audio Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $23.99

Kicker 4-Channel RCA Audio Interconnect Cable

4 Meters (13 ft.) 4-Channel K-Series RCA Audio Interconnect Cable

Your Price $19.95

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1250 Speaker Wire

50 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $29.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

The Install Bay IB-CAP1F

True 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $37.99

e2 ECAP1 by Scosche - Mid-Level 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $49.99

Rockford Fosgate RFC1D - Top of the Line 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $99.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

TN400/4

UPC

715442280032

Weight

8.50lbs

Internal SKU

tn4004

Internal Product ID

11878

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: MTX Audio Terminator TN400/4

  • MTX Audio Car Amplifiers
  • How to Install a Car Amplifier