Expert Service 1-661-257-9993 [Hours]

Hifonics Brutus BRX1516.1D

Out of Stock - Backorder
|

Thanks , You Pay:

$131.24

with warranty

+ FREE Shipping in US 48

Fast, Free Shipping

Within the US 48

60-Day Money-Back

Hassle Free Returns

Low Price Guarantee

Seen it for less? Click here

365-Day Coverage

Warranty assistance for a year

Get FAST answers from customers ASK a Question See questions answers

General Features:

  • Brutus Series Monoblock Class D Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 550 watts x 1 chan.
    • 2 ohms: 900 watts x 1 chan.
    • 1 ohm: 1500 watts x 1 chan.
  • Wired remote bass level control included
  • Pulse Width Modulated MOSFET power supply
  • LED power (green) and protect (red) indicator lights
  • Preamp RCA ouputs allow for daisy chaining multiple amps
  • Heavy duty aluminum alloy heat-sink with illuminated Hifonics logo
  • Lighted connectors and blue wash of light
  • 1-Ohm Stable operation
  • 10 AWG speaker output connections
  • Full-range Preamp RCA outputs to daisy chain multiple amps
    Full-range only if a full range signal is connected to input
  • 3-way system protection circuitry (thermal, overload and speaker short protection)
  • Input sensitivity: 200mV - 9V
  • Frequency Response: 15 - 250 Hz
  • Total Harmonic Distortion (THD): <0.10%
  • Signal to Noise Ration: >95dB
  • Variable low-pass filter: 35 - 250 Hz
  • Subsonic filter: 15 - 35 Hz
  • Variable Bass Boost: 0 to +10 dB bass boost at 45 Hz
  • Variable phase: 0 - 180°
  • Fust Rating: 70A Maxi x 2
  • 4 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Click Here for our contact information.
  • Dimensions: 9.8"W x 12.5"L x 2.4"H
  • Authorized Internet Dealer
  • 90 Day Manufacturer's Warranty
Check out the 2015 Hifonics Brutus Series' Manual Owner's Manual

Also found as: BRX15161D, BRX1516-1D

Specifications

Second Depth
The second depth is used only when the box is slanted or angled. This value is the top measurement and it is measured in inches.
Depth
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
Height
The height of the item, measured from top to bottom, in inches.
Width
The width of the item from left to right (side-to-side) measured in inches.
Color
Color of handle.

Warranty and Return Policy

Parts Warranty Duration
90 days
Labor Warranty Duration
90 days
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Browse 10 questions and 25 answers
Hide answersShow all answers | Sort by
Why did you choose this?
Sonic Electronix Store
good price
olegario z on Nov 24, 2016
I broke My rockford fosgate T1500BD amp and i cant afford to buy another one. So i picked a lesser quality amp
Ryan M on Oct 11, 2016
Good review from a friend
Brandon c on Nov 12, 2016
the brutus amps are the only way to go....alot of power for your money
charles m on May 23, 2016
i just recently purchased a hifonics brutus brx1516.1d and I wanted to pair it with a Kicker 15" L7. My question is i don't know which "OHM" of Kicker 15" L7 to buy (4OHM or 2OHM) my amplifier is "1 OHM Stable" and 1500 watts RMS at 1OHM and that is what "load" i would like to put on it. So do i purchase "one" kicker 15" L7 2 0hm and wire it parallel to amplifier achieve a 1 ohm load to get most power out of amplifier? I would appreciate any help or comments on how the best way to get the most power out of this amplifier and which 15" L7 to pair it with i have heard nothing but great things about the L7 series, and for this sub is ported or sealed box the way to go for loud bass?
A shopper on Aug 22, 2015
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Kicker 11S15L72
Kicker 11S15L72
Best Answer: Hello,

First, so we are on the same page, the drivers are DUAL-2ohm and DUAL-4ohm . This isn't silly semantics, as one can easily confuse what you are saying for a SINGLE-2ohm/4ohm driver, which completely changes the conversation.

To your point, you will require a Dual-2ohm, wired in parallel, to achieve a 1ohm load. However, we do not suggest this, and strongly advise against it. I don't mean to sound rude, I just want to make sure you protect your investment, but if you are not experienced with car audio, then you should attempt powering a 1000w driver with an amplifier that is potentially putting out ~1500w . Instead, my suggestion is going with the Dual-4ohm driver, wired to 2ohms, and staying within the range of the driver's handling. Unless you are absolutely sure that your installer can tune the setup right, and you are responsible enough to not drive the setup to its limits then go with the 1ohm system. =]
Reply · Report · Rick MStaff on Aug 22, 2015
· Add Answer · I Have This Question Too (1)
im trying to decide which brutus will be the best choice to power my 2 kicker cvt shallow mount 10's? the 1515.1d or the1116.1d? each are 400 RMS/800 PEAK
kaenon c on Nov 18, 2015
Best Answer: It really depends on a few things. What ohm are the subs you have? You want to match your subs and amp based on RMS, not peak. This amp is advertised to produce 900watts RMS at a 2 ohm load, which should be enough power to supply both your subs, assuming that your running at a 2 ohm load. Also, it's always a good idea and spend the money upfront for a more powerful amp, if your budget allows, so that way if you ever decide to upgrade in the future you know your amp will be able to supply the power.
Reply · Report · Adam D on Nov 22, 2015
· Add Answer · I Have This Question Too (0)
description says its a mono amp but why does it have 2 positive and negative outputs?
A shopper on Aug 5, 2015
Best Answer: Hello,

The description says its a monoblock, because it is. The two outputs you see are intended to make installer of multiple subwoofers easier. This is a very common setup for "pro style" monoblocks. Examples below..

http://www.sonicelectronix.com/pictures_new.php?id=40252&picture_id=2341480

http://www.sonicelectronix.com/pictures_new.php?id=34764&picture_id=2357346

http://www.sonicelectronix.com/pictures_new.php?id=29472&picture_id=2356525
Reply · Report · Rick MStaff on Aug 6, 2015
· Add Answer · I Have This Question Too (0)
Is this amp 2006 Compliant??
Trent on Mar 19, 2015
Best Answer: It does not have the 2006 compliant cert on the box. A few other notables. The description states that 1/0 gauge wire is required for installation. the amp does not accept 1/0 wire. It accepts 4 gauge wire. You would be wise to run 1/0 to a buss bar or distribution block so you 4 gauge wire runs are short. Also it has(2) 70 amp fusees not 80 amp. The Tech support at maxsonics assured me that the amp is RMS power rated where the Zues line is peak power rated. After all of that. I am driving a single Soundqubed HDS312d2 at 1 ohm in a ported box in the trunk of my crown vic and Damn! All I needed was 1200 watts RMS and I think I got it. there is a war going on in there. I would buy the same amp again. I t would be nice if Sonic electronix made some corrections to the description and ran the amp on there own scope dyno. All RMS rated amps on the site should have the video with the amp output test.

Steve Meade did Amp test Tuesday on an elite Brutus BRX1700 and it put out more power in dynamic test wich is basically like listening to music rather than a constant sine wave and the BRX1700 did 1800 watts. so take that to the bank. Steve Meade doesn't mess around with junk.Brutus amps perform.
Reply (1) · Report · Harold S on Mar 20, 2015
· Add Answer · I Have This Question Too (0)
i purchased this and 2 soundstream r3.12 and they are 2 ohm and i want to bring them down to 1 ohm without hurting the amp how do i do this?

(Moderator Edit: removed all-caps)
JEREMY S on Mar 1, 2016
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Soundstream R3.12
Soundstream R3.12
Best Answer: Hi Jeremy,

What you seek to do Cannot be done - it is physically impossible. Two Dual-2ohm - like you two Soundstream R3.12 - can ONLY be wired to 2ohm final load or 8ohm final load to the BRX1516.1D.
Reply · Report · Rick MStaff on Mar 1, 2016
· Add Answer · I Have This Question Too (0)
I recently purchased these subs along with a Hifonics 1500W Monoblock Brutus Series Super Class D Amp and I'm worried that It won't be enough bang. I still have my Hifonics 2400W Monoblock Brutus Series Super Class D Amp that powered my 12s but I'm sure that's way too much juice. I downsized due to a new car and trunk space. Was the 1516 a good choice?
Marc N on Nov 19, 2015
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Kicker 40DCWR102
Kicker 40DCWR102
Best Answer: Hi Marc,

The answer to your question is in the description of each product. =]

Kicker DCompR10
--RMS: 800 watts total
--Impedance: 2 Ohm final impedance at terminal

Hifonics BRX1516.1D
--2 ohms: 900 watts x 1 chan.

It's a perfect match.
Reply (1) · Report · Rick MStaff on Nov 19, 2015
· Add Answer · I Have This Question Too (0)
i puchased a hifonics brutus brx 1516.1d and paired it with one kicker 15" dvc 4ohm L7 and a sealed box. i have a couple questions, one is i have heard different things about this sub for ported to sealed boxes, that they dont handle power as well in ported boxes and then some say they are louder with less power in a ported box? I understand that there are lots of things can affect this i just wasnt sure if there was truth behind the sub wattage being different in different boxes? as for one of the boxes (ported or vented) being louder in my vehicle i have a 2007 dodge durango which would you recomend for loudest bass? and last question does this subwoofer need to be "broken in"? I never knew if breaking in was true or not for subwoofers and want to get the longest life out of the sub and i greatly appreciate any help and/or recommendations it is awesome to be able to ask professionals questions and get helpful answers thanks again.
A shopper on Aug 24, 2015
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Kicker 11S15L74
Kicker 11S15L74
Best Answer: -just wasnt sure if there was truth behind the sub wattage being different in different boxes?

There is definitely truth behind it, but if it were an "issue" or something worth frying your brain over then Kicker would have added such specs to their manual/literature. Point being, don't worry about it; the ~900w that your amplifier can Potentially drive with is sufficient for either application. Plus, keep in mind, you aren't going to have the setup opened up at full tilt at all times so the power will fluctuate. Again, it's all relative.

-which would you recomend for loudest bass?

Ported enclosures are intended to be "boomy" , therefore perceived as 'louder' .

-last question does this subwoofer need to be "broken in"?

Ideally, yes there is. We always overestimate and suggest +20hrs of casual listening before really 'rocking out'.

Here is Kicker's Tech Support Contact info if you wish to "fry your brain" with information =] :

(405) 624-8583
8am - 5pm CST
support@kicker.com
Reply · Report · Rick MStaff on Aug 24, 2015
· Add Answer · I Have This Question Too (0)
i recently purchased this sub how do i wire one sub (15" L7 4ohm) for a 2ohm load to my amplifier a brutus 1516.1d?
A shopper on Aug 23, 2015
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Kicker 11S15L74
Kicker 11S15L74
Best Answer: Hello,

The driver's manual will outline how to wire it in Parallel to a 2ohm load. Here is our rendition:
http://www.sonicelectronix.com/product/img/subwoofer_wiring/1_sub_DVC_4_ohm_mono.jpg

At the amplifier, pick any pair of opposite polarities (i.e. 1 Positive + 1 Negative) . Yes, ANY PAIR .
Reply · Report · Rick MStaff on Aug 23, 2015
· Add Answer · I Have This Question Too (0)
i just ordered this hifonics amp (BRX 1516.1d) and i ordered a Kicker 15" dual voice coil 4ohm sub that has a selector on the terminal to change the ohm"s from 2/8 to1/4 (kicker40cwr154) and i have never seen this option on a subwoofer,and i have a ported box, i am curious how to wire the sub woofer to acheive 2 ohm"s so i can get more power from the amplifier? I have hooked up sterio"in the past very basic sub and amp hook ups and was wondering if someone could help with wiring options to get the most power from amp. ANY HELP will be greatly appreciated even describing What parallel or impedance and ohm"s mean? I want to hook up and learn at the same time so i understand different specs for subs and amps for now and the future. i hope someone can help! Thank you.
A shopper on Aug 14, 2015
Hifonics BRX1516.1D
Hifonics BRX1516.1D
Kicker 40CWR154
Kicker 40CWR154
Atrend 15SQV
Atrend 15SQV
Best Answer: Hello ,

Unfortunately, we don't have the available space to explain the theories and laws you've requested, but below are two links to get you started. =]

As for your subwoofer question, simply keep the switch at 2ohms if you want a 2ohm final load at the amp . At the amp itself, simply pick any set of 1 Positive and 1 Negative, it doesn't matter which, as long as they are opposite polarities.

http://knowledge.sonicelectronix.com/

http://blog.sonicelectronix.com/
Reply · Report · Rick MStaff on Aug 14, 2015
· Add Answer · I Have This Question Too (0)

Product Summary

Manufacturer

Model Number

BRX1516.1D

UPC

806576223610

Weight

11.40lbs

Internal SKU

ls-brx15161d-obc248141

Internal Product ID

121041

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Hifonics Brutus BRX1516.1D