Expert Service 1-661-257-9993 [Hours]

Kicker 8M 8" Marine Impulse Series

We apologize

This item has been discontinued

Item Added to Cart

Kicker 8M 8" Marine Impulse Series

$34.99

Keep Shopping

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

$39.99

Add
Stinger Sound Dampening Trunk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for your whole trunk!

$64.99

Add
2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

$7.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Kicker 8M 8" Marine Impulse Series.

Get FAST answers from customers ASK a Question See questions answers

  • 8" Marine Waterproof subwoofer
  • 100 watts peak power handling
  • Special Water-Resistant design for Marine Applications
  • Inverted Structural Dome Technology
  • Sealed or Ported boxes recommended
  • Sensitivity: 87 dB

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
8"
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
100 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Single
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Voice Coil Diameter
Diameter of voice coil, usually measured in inches.
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
87 dB
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Rubber
Magnet Structure
Defines the overall structure of the subwoofers magnet.

Recommended Enclosure Specifications

Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.52 cubic feet
Optimum Sealed Box Volume
This value indicates the ideal sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.78 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.52 cubic feet
Optimum Ported Box Volume
This value indicates the ideal ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.78 cubic feet
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
3-7/8"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
7-1/4"

Electromechanical Parameters

Free-Air Resonance (Fs)
The free-air resonance frequency of the subwoofer, measured in Hz. At this frequency the weight of the moving parts is perfectly balanced with the subwoofers suspension system.
Equivalent Compliance (Vas)
This is the amount of air that has the same stiffness as the subwoofers suspension. The greater the rating, the lower the stiffness and larger recommended enclosure. It is measured in Liters.
Total Speaker Q Value (Qts)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including all dimensionless losses. Essentially, a high Qts value (closer to 1.0) means the subwoofer is great for sealed enclosures and a low Qts value (closer to 0) means the woofer is great in vented enclosures. A Qts of around 0.45 means the woofer will work decently in either enclosure type.
Electrical Q Value (Qes)
The subwoofers relative damping (Q) at the resonance frequency (Fs), including electrical losses. Also called the mechanical damping of the subwoofer. The unitless measurement usually varies from 0.5 – 10.
Electrical Resistance of Voice Coil (Re)
Amount of DC resistance of the subwoofer when measured with an ohm meter. Typically, this will read less than the impedance rating of the subwoofer.
Mechanical Q Value (Qms)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including mechanical losses. Also called the mechanical damping of the subwoofer. This unitless measurement usually varies from 0.5 – 10.
Efficiency Bandwidth Product (EBP)
This number represents the trade off between having an efficient woofer and one with a wide bandwidth. To calculate this number, take the Fs and divide it by the Qes. If the number is below 50, the woofer is designed for a sealed enclosure only. If it's between 50-100 it can be used in either. Lastly, if it's greater than 100 it's designed for vented enclosures.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

Your Price $39.99

20 Ft. of Kicker 12 Gauge Speaker Wire

Get true gauge Kicker speaker wire to match your Kicker subwoofer!

Your Price $39.95

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

Stinger Sound Dampening Trunk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for your whole trunk!

Your Price $64.99

Dynamat Sound Dampening Trunk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $94.95

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $18.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $74.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $7.99

12 oz. Can of Adhesive Spray

Spray adhesive used for adhering carpet to subwoofer boxes without bubbles.

Your Price $8.99

Spring Post Terminal Cup

Makes adding a spring post terminal to an enclosure simple! Banana clip ready!

Your Price $3.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $1.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

8M

Weight

8.00lbs

Internal SKU

im8

Internal Product ID

1936

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Kicker 8M 8" Marine Impulse Series