Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Boston Acoustics GT-5750

775W RMS, GT Series 5-Channel Reference Amplifier

Discontinued
|

We apologize

This item has been discontinued

Boston Acoustics GT Reference Series Amplifiers

Boston Acoustics GT Reference amplifiers are perfect for just about any situation and any installation. The GT-5750 5-channel amplifier has a CEA-2006-A power rating of 70W x 4 channels @ 4 ohms + 250 watts x 1 channel @ 4 ohms, and 100W x 4 channels @ 2 ohms + 375 watts x 1 channel @ 2 ohms. All of these ratings give the amplifier unsurpassed versatility, whether you are amplifying a set of speakers or even a subwoofer. Q-Tune™ technology will combine your main speakers with the subwoofers, giving you bass up front and a whole new way of enjoying your music. The unique forced air cooling system allows for extreme heat dissipation and installation anywhere without the need to worry of thermal overload. Variable low and high crossovers combined with the Q-Control feature will give you complete control of all frequencies to better fine tune your audio system to better meet your personal preferences. GT Reference amplifiers provide unmatched technology and reliable power output, they are easy to install and are capable of stereo or mono operation with its DualMode™ feature. With all of its features and technologies GT Reference amplifiers are a great choice when selecting an amplifier.

  • GT Reference Series 5-Channel Amplifier
  • RMS Power Rating(CEA-2006-A):
    • 4 ohms: 70 watts x 4 chan. + 250 watts x 1 chan.
    • 2 ohms: 100 watts x 4 chan. + 375 watts x 1 chan.
    • chan.
  • RMS Power Rating(12V):
    • 4 ohms: 50 watts x 4 chan. + 275 watts x 1 chan. (2 ohms)
  • Remote bass level input (GT-RSL remote level control sold separately)
  • Red LED power badge and orange protect indicator
  • 5/4/3/2 channel operation
  • Adjustable mounting feet (mounting feet move along rails to allow the easiest installation)
  • Fully computer-controlled diagnostics system (continuously monitors amplifier in case of thermal overload, short circuits, or over voltage)
  • Q-Tune™ technology combines sophisticated crossover adjustments with Q-Control settings to seamlessly transition rear bass to the front sound stage
  • Heavy duty forced cooled aluminum alloy heatsink
  • Gold-plated RCA level inputs
  • Gold-plated screw terminals
  • Variable high-pass filter (20-250 Hz, 12 dB/octave)
  • Variable low-pass filter (50-350 Hz, 12 or 24 dB/octave)
  • Signal Voltage Input (200mV-8V)
  • Frequency response: 10-95,000 Hz
  • Dimensions: 22-1/4"L x 9"W x 2-3/8"H
  • 4-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
  • 1-year Manufacturer's warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

70 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

100 watts x 4 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

Not Stable

Power Specifications - Subwoofer Channel

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
250 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
375 watts x 1 channels
RMS Power @ 1 ohm
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 1 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
Not Stable

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
5
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

775 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.03%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

20 - 250 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 350 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
100 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Optional (Accessory required and sold separately)
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
100A x 1 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
75%
4 Star
25%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
4.5
Value
4.5
Features
4.5
Design
4.5
Usability
5.0

Brandon

Granger, IN

Overall
Durability
Value
Features
Design
Usability

Good amp

September 13, 2011

Good amp, I really like the fact its fan cooled when its needed. I installed this in place of a 2 channel amp and running speakers off a Alpine head unit with the bigger 27x4 rated amp. More power is better. Running everything off this amp and it sounds great. About perfect match for my 2 12" infinity kappa perfects. Only complaint really is the plastic tabs that you mount it with seem a little weak but no issues so far.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Anthony

Wayne, NJ

Overall
Durability
Value
Features
Design
Usability

Amp does everything and then some

August 10, 2011

I replaced two smaller rockford amps, a 4 channel and a 2 channel for this amp. It is way cleaner and way louder. I am glad I bought this Amp. It is a little costly, but well worth it.

0 of 0 found this helpful

Help our customers find the most helpful reviews

huskie

Australia

Overall
Durability
Value
Features
Design
Usability

excellent product

May 24, 2011

this product is excellent the system sound great the price is just right would buy again

0 of 0 found this helpful

Help our customers find the most helpful reviews

Wil

Orlando, FL

Overall
Durability
Value
Features
Design
Usability

Great Amp & Perfect Solution!

March 21, 2011

I recently purchased this to replace an (2) amps an Infinity 475 and 1300, after I lost a channel in the 475. It is paired with a set of Infinity 60.7's components and a pair of 63.9i's and I am adding a RF shallow mount 10" in the small space behind the rear driver's side seat in my 4dr Tacoma. I thought it would have similar performance, because it has simliar specs at 2 Ohms, but HOLY CRAP! This Amp is 10x cleaner than the infinity's, and is more powerful by far. The single amp has allowed me to reconfigure my system so that everything appears stock and I have not had to destroy any stock trim. I am absolutely thrilled, Thank you for allowing me to purchase this product!!!!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XKIT44 4-Gauge 4-Channel Wiring Kit

4-Channel 100% OFC Complete True 4 Gauge Amp Kit with RCA Cables and Speaker Wire

Your Price $99.99

T-Spec V12-4DAK 4-Channel 4-Gauge Wiring Kit

Get everything you need to hook up your new amplifier!

Your Price $119.95

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

Stinger SI4617 4000 Series Interconnect Cable

17 ft. 6-Channel 4000 Series Audio Interconnect Cable

Your Price $41.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

XIX2025 Strapping RCA

0.25 Meter (0.86 ft) Hyper-Flex RCA cable w/ Serpentine-Cut Nickel Plated Connectors

Your Price $12.99

Product Summary

Manufacturer

Model Number

GT-5750

UPC

0690283474683

Weight

15.00lbs

Internal SKU

gt5750

Internal Product ID

19568

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Boston Acoustics GT-5750