Expert Service 1-877-289-7664 [Hours]

Boom. SUBTEMBER is here!

Diamond Audio D3 400.4

D3 Series 4-Channel Amplifier D3400.4

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

  • Black anodized aluminum finish
  • Raised Diamond Audio Technology logo
  • Variable High/Low pass crossover (55 - 550 Hz, 12 dB/Oct)
  • Varible bass boost (0 - 18dB @ 45 Hz)
  • Adjustable input level controls with ground loop isolation (500mV - 5V)
  • PWM MOSFET Power supply with low AM RFI and protection circuits for overheating and sepaker shorts
  • RCA Inputs: 2 pair
  • Gold-plated input/output connectors and an external automotive type fuse
  • Remote turn-on with "soft start" musting to prevent "thump"
  • Dimensions: 13" L x 8-1/2" W x 2-1/4" H
  • 1-year SonicElectronix.com warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

57 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

88 watts x 4 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

Not Stable
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

182 watts x 2 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

700 watts approx.

Power Specifications - Subwoofer Channel

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
RMS Power @ 1 ohm
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 1 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage. Often times this maximum is achieved during a brief musical burst, such as a drum accent or low bass hit. Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. This is the peak power output for the amplifier's 5th channel.

Amplifier Specifications

Amplifier Series
This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

364 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.05%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
100 dB
Channel Separation
Also referred to as crosstalk. The amount of interference on one stereo channel caused by the leaking of the other stereo channel. The higher the rating in decibels (dB), the better the Channel Separation.
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
40A
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Strappable
Some amplifiers can be "strapped" together in order to increase the output of a single audio channel. These amplifiers feature RCA preamp outputs, allowing you to pass the signal directly from one amp to the other to ensure consistency.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
4.5
Usability
5.0
coleon

detroit

Overall
Durability
Value
Features
Design
Usability
flyin hi's

September 12, 2011

This amp is very cool and the amazing hi sound quailty it unleash will make your music so clear like flyin hi's.

0 of 0 found this helpful

Help our customers find the most helpful reviews

John

Mount Pleasant, MI

Overall
Durability
Value
Features
Design
Usability
Definately an audiophile quality amp at an affordable price

May 7, 2005

I run this amp on my main speakers. It is clean, has excellent features, very efficient, and is very affordable when compared to other amps w/ the same features and quality. I run 4 Kenwood eXcelon 2-ways off this amp and they produce extremely clean SQ. I am very impressed w/ the quality and technology that goes into these amps. I highly suggest these amps to anyone wanting a high quality amp for an affordable price. The quality and technology is that of amps twice it's price. Definately a good buy.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $59.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB8

8 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIV45 4-Channel RCA Audio Interconnect Cable

5 Meters (16.4 ft.) 4-Channel RCA Audio Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $23.99

Kicker K-Series RCA Interconnect Cable

19 ft. of 4-Channel RCA cable with dual twisted-pair conductors, hyper-flex technology, and gold plated contacts for maximum signal transfer!

Your Price $29.95

StreetWires ZN7 RCA Interconnect Cable

16.4 ft. of 4-Channel RCA Cable with hyper twist construction, oxygen free copper, and precision machined tips.

Your Price $59.99

Kicker 4-Channel RCA Audio Interconnect Cable

4 Meters (13 ft.) 4-Channel K-Series RCA Audio Interconnect Cable

Your Price $19.95

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1250 Speaker Wire

50 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $29.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

The Install Bay IB-CAP1F

True 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $37.99

e2 ECAP1 by Scosche - Mid-Level 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $49.99

Rockford Fosgate RFC1D - Top of the Line 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $104.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

D3-400.4

Weight

12.00lbs

Internal SKU

d34004

Internal Product ID

2997

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Diamond Audio D3 400.4