Expert Service 1-877-289-7664 [Hours]

Kicker Solo-Baric S10L34 (11S10L34)

10" Dual 4 ohm Solo-Baric L3 Series Car Subwoofer

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

  • 10" Dual 4 Ohm Solo-Baric L3 Series Subwoofer
  • Power Handling:
    • Peak: 800 watts
    • RMS: 400 watts
  • Impedance: Dual 4 ohm
  • Patented corner-ribbed, double-stitched Santoprene rubber surround
  • Stamped steel basket protects massive internal motion
  • Titanium deposit impregnated cone with rolled outer edge
  • Vented 360 back bracing
  • Rear foam gasket
  • Heat-dissipating, solid pole piece and high-temp coil wire for longer woofer life
  • Spring loaded terminals
  • Poly-cotton semi-progressive spider
  • Heat-dispersing, solid pole piece
  • Spiralead tinsel leads
  • High-temperature dual 4 ohms voice coils
  • Sensitivity: 85.3 dB
  • Other search terms: S10L3, S10L34, 10L3, 10L34, 11S10L34
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
2011 Kicker Authorized Online Dealer and eBay Seller

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
Solo-Baric L3 (Kicker)
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
800 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
400 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Voice Coil Diameter
Diameter of voice coil, usually measured in inches.
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
85.3 dB
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Square
Main Cone Color
This is the color of the speaker's or subwoofer's cone.
Black
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Titanium Deposit Impregnated Cone w/ Rolled Outer Edge
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Santoprene Rubber
Magnet Structure
Defines the overall structure of the subwoofers magnet.
Subwoofer Grille
Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
Optional (Accessory required and sold separately)
Re-Cone Kit Available
Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
No

Recommended Enclosure Specifications

Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Sealed
Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.8 cubic feet
Optimum Sealed Box Volume
This value indicates the ideal sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
3.0 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.25 cubic feet
Optimum Ported Box Volume
This value indicates the ideal ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
2.25 cubic feet
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
5-1/2"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
9-5/16"
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No

Electromechanical Parameters

Free-Air Resonance (Fs)
The free-air resonance frequency of the subwoofer, measured in Hz. At this frequency the weight of the moving parts is perfectly balanced with the subwoofers suspension system.
Equivalent Compliance (Vas)
This is the amount of air that has the same stiffness as the subwoofers suspension. The greater the rating, the lower the stiffness and larger recommended enclosure. It is measured in Liters.
Total Speaker Q Value (Qts)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including all dimensionless losses. Essentially, a high Qts value (closer to 1.0) means the subwoofer is great for sealed enclosures and a low Qts value (closer to 0) means the woofer is great in vented enclosures. A Qts of around 0.45 means the woofer will work decently in either enclosure type.
Electrical Q Value (Qes)
The subwoofers relative damping (Q) at the resonance frequency (Fs), including electrical losses. Also called the mechanical damping of the subwoofer. The unitless measurement usually varies from 0.5 10.
Electrical Resistance of Voice Coil (Re)
Amount of DC resistance of the subwoofer when measured with an ohm meter. Typically, this will read less than the impedance rating of the subwoofer.
Mechanical Q Value (Qms)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including mechanical losses. Also called the mechanical damping of the subwoofer. This unitless measurement usually varies from 0.5 10.
Efficiency Bandwidth Product (EBP)
This number represents the trade off between having an efficient woofer and one with a wide bandwidth. To calculate this number, take the Fs and divide it by the Qes. If the number is below 50, the woofer is designed for a sealed enclosure only. If it's between 50-100 it can be used in either. Lastly, if it's greater than 100 it's designed for vented enclosures.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
50%
4 Star
50%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
4.8
Value
4.3
Features
5.0
Design
5.0
Usability
5.0

tricky

Canada

Overall
Durability
Value
Features
Design
Usability

clean sound

October 27, 2012

Definitely recommend to anyone. Have one of these in a small box behind the seat of my work van being pushed with a kicker DX1000.1 and it handles no problem. Definitely baby it till it breaks in then no problems handling anything after that.

1 of 1 found this helpful

Help our customers find the most helpful reviews

Anthony

Chino, CA

Overall
Durability
Value
Features
Design
Usability

Solid Bass

April 6, 2011

Got this L3 wired up to a 450 watt RMS amp in a sealed box this sub puts out loud high impact bass sounds like a 12" sub except with harder knockin bass. I think maybe the sound quality is a bit better with the round subwoofer I don't know maybe its just me. Also I think its a bit pricey.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Ed

Kissimmee, FL.

Overall
Durability
Value
Features
Design
Usability

Great deep sound!!!

March 20, 2011

I have a 97 Eclipse Spyder. Since is a convertible I don't have much room for subwoofers in the limited trunk. So, I went to an audio store owned by a friend of mine and asked for a good subwoofer where I could only need one and still have a great loud sound. He recommended me the 12" Kicker L3, mounted on a just perfect size box for the space I have. And boy........ I'm glad I bough it, great sound, deep, and loud. Definitely sounds like I have more than one sub in the trunk. Love it.

0 of 0 found this helpful

Help our customers find the most helpful reviews

jake

Butler, PA

Overall
Durability
Value
Features
Design
Usability

Simply awesome

March 8, 2011

I bought one 10" L3, made a box with internal volume of .9 and I'm impressed. This sub definately sounds more like a Comp VR 12". It hits a much wider range of frequencies than other 10" subs. It actually sounds pretty clean in a sealed box to. I can't really comment about the durability cause I only had it hooked up for a couple days, but this thing bangs! The sub is rated at 400 RMS but, only handles 350 RMS so watch how much you put on it. Buy it and you'll be happy!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

10 Single Sealed Solobaric Truck Subwoofer Box

Perfect fit for behind or even under the seat of your truck!

Your Price $69.95

10 Single Sealed Solobaric Hatchback Subwoofer Box

Ideal 10" subwoofer enclosure for Hatchback vehicles.

Your Price $59.95

10" Single Ported/Vented Pro Solo-Baric Subwoofer Enclosure

Designed for the Pro Solo-Baric L7 Subwoofer.

Your Price $79.95

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

Your Price $39.99

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

20 Square Feet of Sound Dampening Material

NVX Sound dampening is thicker than competitors, eliminates rattles and gives you bigger bass!

Your Price $59.99

Dynamat Sound Dampening Trunk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $109.95

Stinger Sound Dampening Trunk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for your whole trunk!

Your Price $69.99

20 oz. Bag of Poly-Fil

Polyester fiber fiberfill adds better bass to your system.

Your Price $5.99

12 oz. Can of Adhesive Spray

Spray adhesive used for adhering carpet to subwoofer boxes without bubbles.

Your Price $6.99

Spring Post Terminal Cup

Makes adding a spring post terminal to an enclosure simple! Banana clip ready!

Your Price $3.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $3.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $79.99

4 Ft of 1/4" Thick Black Heat Shrink Tubing

Provides abrasion resistance and added protection for your cables.

Your Price $3.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $8.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

AutoSound 2000 CD-101

Low frequency test CD

Your Price $11.99

Impedance Meter / Signal Generator

Easy to locate tuning frequencies of passive radiators and ported enclosures

Your Price $299.99

1 Kicker Solo-Baric S10L34 (11S10L34) Subwoofer

Mono Amp

2 Channel Amp - Bridged

2 Kicker Solo-Baric S10L34 (11S10L34) Subwoofers

Mono Amp

Mono Amp - Option 1

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp - Bridged

3 Kicker Solo-Baric S10L34 (11S10L34) Subwoofers

Mono Amp

4 Channel Amp

4 Kicker Solo-Baric S10L34 (11S10L34) Subwoofers

Mono Amp

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

11S10L34

Weight

13.20lbs

Internal SKU

11s10l34

Internal Product ID

31859

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Kicker Solo-Baric S10L34 (11S10L34)

  • Kicker Solo-Baric L3 Square Car Subwoofer
  • Subwoofer Size Buying Guide