Expert Service 1-877-289-7664 [Hours]

Labor Day Sale

Kenwood KEC-600 6-way Crossover

We apologize

This item has been discontinued

Item Added to Cart

Kenwood KEC-600 6-way Crossover


Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
Add Warranty
3 years of protection

Get FAST answers from customers ASK a Question See questions answers

  • 6-Way Electronic Crossover Network
  • Front Mid: LPF(800 Hz - 10 kHz), HPF(30 Hz - 800 Hz), Level(Off - 0 dB), On/Through Switch
  • Front High: HPF(800 Hz - 10 kHz), Level(Off - 0 dB), Phase Switch(180°)
  • Rear Mid: LPF(800 Hz - 10 kHz), HPF(30 Hz - 800 Hz), Level(Off - 0 dB), On/Through Switch
  • Rear High: HPF(800 Hz - 10 kHz), Level(Off - 0 dB), Phase Switch(180°)
  • Low 1:Operation Switch (Rear, F+R, AUX), LPF(30 Hz - 800 Hz), Level(0 - +10 dB), Phase Switch (180°), Mono/Stereo Switch
  • Low 2:Operation Switch(Front, Rear, F+R), LPF(120 Hz - 800 Hz), Subsonic(30 Hz - 120 Hz), Level(Off - 0 dB), Phase Switch(180°), Mono/Stereo Switch
  • Parametric EQ: Low1/Low2 Switch, Freq. Control(30 - 300 Hz), Level Control(-10 - +10 dB)
  • RCA Inputs: 3 Pair
  • RCA Outputs: 6 Pair
  • Acrylic Panel
  • Ground Screws for RCA Cables w/ Ground Wire
  • Mounting Hardware
  • Signal to Noise Ratio: 100 dB
  • THD: 0.01%
  • Frequency Response: 20 Hz - 100 kHz
  • 12 dB/Oct Crossovers(Mono Mode 18 dB/Oct)
  • 3A Fuse
  • Dimensions: 11-1/5" W x 1-15/16" H x 7-7/8" D
  • 1-year warranty

General Specifications

Equalizer Bands
The number of graphic or parametric equalizer bands the receiver has. The better the EQ, the more likely you will be able to "tweak" your sounds to your desire.
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Built-in Bass Reconstruction
Bass reconstructors, or bass enhancers, improve low frequency reproduction in a car audio system with at least one subwoofer. These bass expander products will help your subs produce accurate bass thumps.
Line Driver
A line driver is a small amplifier used to support the strength of the audio signal coming from the source unit.
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Total Number of Inputs
This is the total number of input connections that go into the unit.
Total Number of Outputs
This is the total number of output connections that the unit will produce.
Equalizer Frequencies
The frequency range that allows control of the center frequency of each equalization band.
30 Hz - 800 Hz, 800 Hz - 10 kHz
Signal Boost/Cut
The available signal boost or cut for each of the frequency bands.
-10 - +10 dB/Off - 10 dB
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
20 - 100000 Hz
THD (Total Harmonic Distortion)
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
100 dB
The width of the item from left to right (side-to-side) measured in inches.
The height of the item, measured from top to bottom, in inches.
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.

Specials with this Item

Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
4 Star
3 Star
2 Star
1 Star

Average Attribution Rating

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary


Model Number




Internal SKU


Internal Product ID


Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Kenwood KEC-600 6-way Crossover