Expert Service 1-877-289-7664 [Hours]

Expert advice for 14 years

2000W RE Audio + Sound Dampening Material Bass Bundle

15" RE Audio XXX15D4 XXX Series Subwoofer + NVX Sound Dampening Material

Discontinued
|

We apologize

This item has been discontinued

RE Audio plus Sound Dampening Material Bass Bundle

This Sonic Electronix Exclusive Bundle showcases a 15" Dual 4 Ohm RE Audio XXX Series Subwoofer. This subwoofer is rated at 2000 watts RMS of continues power. The subwoofer is equipped with a Kevlar reinforced kraft pulp dual composite 2-piece cone and a rubber surround for rigidity and performance. It is also equipped with tork-tite terminals, and dual progressive spiders for increased excursion. With an VMS vented magnet system that reduces heat excursion, this RE Audio XXX series subwoofer is sure to provide efficient sound and bass for long periods of time. In order to improve the all around sound of your audio car system, this bundle also includes ten 18" x 32" pieces of sound dampening material. This dampening material will help reduce engine noise, vibrations, road noise and rattling to give you a higher sound quality. Four step peel and stick application makes installation simple and efficient. This sound dampening material is sure to improve the over all quality and output of your system.


 
RE Audio XXX15D4 Features:
  • 15" Dual 4 ohm XXX Series Car Subwoofer
  • Power Handling:
    • RMS: 2000 watts
  • Impedance: Dual 4 ohm
  • Kevlar reinforced kraft pulp, dual composite 2-piece cone
  • Rubber surround
  • Integrated tinsel leads
  • FEA Optimized motor structure
  • Dual progressive spiders
  • Integrated gasket
  • Tork-Tite terminals
  • 3" 4-Layer aluminum flat wire voice coil
  • Split coil design
  • VMS Vented magnet system
  • Cast aluminum basket
  • Triple stacked magnets
  • Designed specifically for sealed or ported enclosures
  • Proudly made in the USA
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
XXX 15" T/S Parameters:
  • Electrical Q Value (Qes): 0.58
  • Mechanical Q Value (Qms): 3.62
  • Total Speaker Q Value (Qts): 0.501
  • Free Air Resonance (Fs): 19.10 Hz
  • Equivalent Compliance (Vas): 207 liters
  • One-Way, Linear Excursion (Xmax): 54 mm
  • Efficiency (SPL 1W/1m): 85.81 dB SPL
  • Effective Piston Area (Sd): 810 cm2
  • DC Resistance (Re): 4.2 ohm
  • Nominal Impedance (Znom): Dual 2 ohm
  • Thermal Power Handling (Pe): 2000 W
  • Force Factor (Bl): 18.16

For more information on the Thiele and Small Parameters, visit our T/S Parameters Article

NVX SDBP40 Features:
  • Ten 18" x 32" Pieces of Dead Shield Sound Dampening Material
  • Eliminates road noise
  • Quiets vibrations
  • Stops rattles
  • Increases SPL
  • Reduces heat
  • Easy to form aluminum conforms to desired area of vehicle with ease
  • Four step peel and stick design for easy installation
  • Increases sound quality and output of car audio system
  • Up to 30% thicker than the leading competitors
  • 40 Square feet total
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty
  • Dimensions (each piece): 18"L x 32"W
  • Subwoofer Specifications

    Subwoofer Series
    Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
    XXX (RE Audio)
    Subwoofer Size
    Refers to the diameter of the subwoofer, measured in inches.
    15"
    RMS Power Handling
    The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
    2000 watts
    Voice Coil(s)
    Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
    Dual
    Impedance (Per Voice Coil)
    The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
    4 ohms
    Xmax (millimeters)
    Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
    54 mm
    Subwoofer Design
    This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

    Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

    Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

    Round / Circle
    Main Cone Color
    This is the color of the speaker's or subwoofer's cone.
    Black
    Woofer Composition
    Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
    Kevlar reinforced kraft pulp, dual composite 2-piece cone
    Woofer Surround
    A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
    Rubber
    Subwoofer Grille
    Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
    No
    Re-Cone Kit Available
    Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
    No

    Recommended Enclosure Specifications

    Recommended Enclosure Type
    This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

    Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

    Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

    Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

    Ported / Vented
    Sealed
    Minimum Sealed Box Volume
    This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
    1.6 cubic feet
    Maximum Sealed Box Volume
    This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
    2.1 cubic feet
    Minimum Ported Box Volume
    This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
    3.2 cubic feet
    Maximum Ported Box Volume
    This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
    4.0 cubic feet
    Top-Mount Depth
    The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
    13-1/2"
    Cutout Diameter
    The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
    14-1/2"
    Shallow Mount Installation
    This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

    Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

    No

    Warranty and Return Policy

    Parts Warranty Duration
    1 year
    Labor Warranty Duration
    1 year
    Warranty Provider
    Manufacturer

    Summary of Customer Ratings & Reviews

    Rating Distribution

    5 Star
    100%
    4 Star
    0%
    3 Star
    0%
    2 Star
    0%
    1 Star
    0%

    Average Attribution Rating

    Durability
    5.0
    Value
    4.5
    Features
    5.0
    Design
    5.0
    Usability
    5.0

    bradley

    mesa, AZ

    Overall
    Durability
    Value
    Features
    Design
    Usability

    ridiculos

    April 9, 2012

    Ridiculous. One word only. Look it up... can you say deaf ears in 2 seconds of playtime!

    0 of 0 found this helpful

    Help our customers find the most helpful reviews

    jack56

    Park Rapids, MN

    Overall
    Durability
    Value
    Features
    Design
    Usability

    best value

    August 15, 2011

    Seem to be the best price for this product.

    0 of 0 found this helpful

    Help our customers find the most helpful reviews

    Accessory Tools and Products

    Accessories added

    NVX 20 ft. of True Spec 8 Gauge Speaker Wire

    Flexible multi-strand cable bends and twists to meet your installation needs.

    Your Price $49.99

    25 ft. of Streetwires 12 Gauge Speaker Cable

    You'll need speaker wire to hook up that new subwoofer!

    Your Price $44.95

    Belva 23 ft. of 12 Gauge Speaker Wire

    Ultra-flexible PVC blended jacket for easy installation.

    Your Price $14.99

    15 Dual Sealed Single Cab Truck Subwoofer Box

    Durable 11/16" Medium Density Fiberboard (MDF) construction.

    Your Price $89.95

    Single 15" Sealed MDF Subwoofer Enclosure

    15-inch Sealed Car Sub Box Made with 3/4" MDF and lined w/ Polyfil.

    Your Price $44.99

    15" Single Slot Ported/Vented Pro Subwoofer Enclosure

    Durable 3/4" Medium Density Fiberboard (MDF) construction.

    Your Price $69.95

    Dynamat Sound Dampening Bulk Kit

    Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

    Your Price $151.95

    Stinger Sound Dampening Bulk Kit

    Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

    Your Price $109.99

    Gold Plated Dual Terminal Banana Plug Connector

    Enables an expandable, secure connection accepting up to 8 gauge wire.

    Your Price $4.99

    Car Stereo and Speaker Installation Tool Kit

    Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

    Your Price $12.99

    Xscorpion 9-Piece Nylon Plastic Pry and Chisel Tool Set

    Easily removes dash/trims, door clips, panels and pins, rubber grommets and vehicle emblems.

    Your Price $14.99

    4 Ft of 1/4" Thick Black Heat Shrink Tubing

    Provides abrasion resistance and added protection for your cables.

    Your Price $3.99

    2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

    Universal rubber roller to make it easy to install sound dampening.

    Your Price $7.99

    1mm All Purpose Solder

    Solder is all purpose for use on most projects where solder is needed.

    Your Price $8.99

    15" Protective Waffle Metal Subwoofer Grille

    Keep your subwoofer looking amazing while keeping it safe with its durable metal construction!

    Your Price $6.99

    Scosche SPL Meter

    Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

    Your Price $21.99

    AutoSound 2000 CD-101

    Low frequency test CD

    Your Price $11.99

    Impedance Meter / Signal Generator

    Easy to locate tuning frequencies of passive radiators and ported enclosures

    Your Price $299.99

    1 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofer

    Mono Amp

    2 Channel Amp - Bridged

    2 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

    Mono Amp

    Mono Amp - Option 1

    2 Channel Amp

    2 Channel Amp - Bridged

    4 Channel Amp - Bridged

    3 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

    Mono Amp

    4 Channel Amp

    4 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

    Mono Amp

    2 Channel Amp

    2 Channel Amp - Bridged

    4 Channel Amp

    Items we think you might want

    XXX15D4 thumbnail

    RE Audio XXX15D4

    • RMS Power: 2000W
    • Dual 4 ohm
    • Rubber Surround
    • Dual Composite 2-Piece Cone
    • Tork-Tite Terminals
    • Dual Progressive Spiders
    • Triple Stacked Magnets
    • Flat Wire Voice Coil
    • Venting System

    Your Price $599.99

    Product Summary

    Manufacturer

    Model Number

    XXX15D4_SDBP40

    Weight

    134.00lbs

    Internal SKU

    xxx15d4_sdbp40

    Internal Product ID

    37362

    Sonic Electronix Wiring Guide

    Wiring Diagram Legend

    Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

    Product Name: 2000W RE Audio + Sound Dampening Material Bass Bundle