Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Power Acoustik D1-2000D

2000W Monoblock Class D Demon Series Car Amplifier

In Stock. Only 3 Left!
|

List price $199.95

$84.99

with warranty

You Save: $114.96 (57.49%)

Arrives by Thursday, July 31 to zip 98109

Add an Extended Warranty

Fast, Free Shipping

Within the US 48

60-Day Money-Back

Hassle Free Returns

Low Price Guarantee

Seen it for less? Click here

365-Day Coverage

Warranty assistance for a year

In Stock

Arrives by Thu, July 31

  • Demon Series Monoblock Class D Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 600 watts x 1 chan.
    • 2 ohms: 900 watts x 1 chan.
    • 1 ohm: 1,200 watts x 1 chan.
  • Max power output: 2,000 watts x 1 chan.
  • Pulse Width Modulated MOSFET power supply
  • Wired remote bass level control included
  • LED power and protect indicators
  • Variable Bass Boost (0 to +18 dB)
  • Soft Start Turn-on
  • Mono channel operation
  • Preamp RCA outputs to daisy chain multiple amps
  • 2-Way System Protection circuitry
  • Heavy duty aluminum alloy heatsink for extreme heat dissipation
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Input sensitivity:
    • Low level: 100mV-2V
    • High level: 2V-8V
  • Variable low-pass filter (50-150 Hz)
  • Subsonic filter (10-40 Hz)
  • Phase Shift: 0-180°
  • Damping factor: >180
  • Frequency response: 50-150 Hz
  • Also Available in: Black
  • Dimensions: 11-5/8"L x 11-13/16"W x 2-5/8"H
  • 0-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

Power Specifications - Subwoofer Channel

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
600 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
900 watts x 1 channels
RMS Power @ 1 ohm
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 1 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
1200 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage. Often times this maximum is achieved during a brief musical burst, such as a drum accent or low bass hit. Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. This is the peak power output for the amplifier's 5th channel.
2000 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

2000 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

1200 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
1 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
Not Bridgeable
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.01%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 150 Hz
Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
10 - 40 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
103 dB
Channel Separation
Also referred to as crosstalk. The amount of interference on one stereo channel caused by the leaking of the other stereo channel. The higher the rating in decibels (dB), the better the Channel Separation.
90 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
25A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
56%
4 Star
22%
3 Star
11%
2 Star
0%
1 Star
11%

Average Attribution Rating

Durability
4.0
Value
3.9
Features
4.4
Design
4.2
Usability
4.2

Steven

Jensen Beach, FL

Overall
Durability
Value
Features
Design
Usability

Great amp

May 18, 2012

I chose this amp from my personal experiences with power acoustic amps. It pounds the two 12s it powers with no problem. No issues at all and had a bass knob included. All for just over 100.

2 of 2 found this helpful

Help our customers find the most helpful reviews

Bj

Montezuma,Ga

Overall
Durability
Value
Features
Design
Usability

Great Value

July 17, 2014

I love this amp the best one I ever had!

0 of 0 found this helpful

Help our customers find the most helpful reviews

The amp master

Las Vegas

Overall
Durability
Value
Features
Design
Usability

PA D1-2000D

May 3, 2012

If you are a bass head, this is definitely not the amp. I purchased this amp, and after 15 minutes of playing, it goes into protect mode running it at 1 ohm. Does not perform like a class D amp; more like a 2 channel amp. This amp is weak, and I really do not recommend this amp.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Patrick

Coarsegold, CA

Overall
Durability
Value
Features
Design
Usability

Killer

April 13, 2012

I've got this thing running at 1ohm with a 2ohm dvc SPL 12", and it bumps so hard. The design is a little cheesy, but if you're into the light up eyes, that's cool. I would definitely buy another one of these!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Rob

Silverdale, WA

Overall
Durability
Value
Features
Design
Usability

Horrible Amp

March 19, 2012

I installed this amp on 2 Alpine Type R 12's and have tried running it at both 1 ohm and 4 ohm and does nothing but switch to protect mode with the gain no more than 1/4 of the way turned up. Even tried hooking it up to just one at a 2 ohm and still does the same thing. Even if it did work this amp puts out at most 720watts with the 2 onboard fuses. Would not recommend this amp to anyone.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Alan

chattanooga, TN

Overall
Durability
Value
Features
Design
Usability

Great product

March 18, 2012

No problems, great product.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Dev

PEELL, WA

Overall
Durability
Value
Features
Design
Usability

this amp is amazing

February 8, 2012

I just got this amp installed for my 2 alpine 12's and they pound so much harder! It looks awesome, i love the light up eyes, and the bass boost. The best part is price, you won't find a better amp for this low of a price. Also, you can buy 2 or 3 and strap them together for more power! I highly recommend the Demon Series.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Brian

Cincinnati, OH

Overall
Durability
Value
Features
Design
Usability

Fantastic Amp, Awesome sound

December 19, 2011

This amp puts out more than enough power for any car. My 2 12" Pioneers give me a massage. The whole time i'm driving with this amp in the trunk.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Tito

Wisconsin

Overall
Durability
Value
Features
Design
Usability

Good Amp

August 18, 2011

I would recommend this amp; a few people mistake this amp for a lower voltage, these RMS ratings are for 14.4v amperes. runs a little weaker rms with 12 volts.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XKIT42 100% OFC True 4 Gauge Wiring Kit with RCA Cables and Speaker Wire

The reviews speak for themselves, this is awesome wire with everything you need!

Your Price $89.99

Power Acoustik AKIT-4 4 Gauge Wiring Kit

Get a Power Acoustik wiring kit to match your new Power Acoustik amplifier!

Your Price $32.99

Belva BAK42 4 Gauge Amplifier Installation Kit

Great amps need great wire at a great price. This amp kit has everything you need!

Your Price $29.99

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

StreetWires FB0

1/0 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft of V-Series 2-Channel RCA Audio Premium Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $11.99

NVX XIX25 X-Series RCA Interconnect Cable

16.4 ft. of 4-Channel X-Series RCA Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $26.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

Product Summary

Manufacturer

Model Number

D1-2000D

UPC

709483038325

Weight

9.00lbs

Internal SKU

d12000d

Internal Product ID

37802

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Power Acoustik D1-2000D