Expert Service 1-661-257-9993 [Hours]

Renegade + U.S. Amps Amplifier and Speaker Bundle

2 Sets of 5-1/4" RX52 Renegade Speakers + U.S Amps XA-800.4 4-Channel Amplifier + Kit + Sound Damp

We apologize

This item has been discontinued

Item Added to Cart

Renegade + U.S. Amps Amplifier and Speaker Bundle

2 Sets of 5-1/4" RX52 Renegade Speakers + U.S Amps XA-800.4 4-Channel Amplifier + Kit + Sound Damp

$138.72

Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
$16.99
Add Warranty
3 years of protection

NVX XKIT84 4-Channel 8-Gauge Wiring Kit

In case you didn't know, NVX has top notch wire and this kit has everything you need!

$69.99

Add
Five Piece Installer's Panel Removal Tool Kit

Helps with removing dash and trim panels during installation.

$11.99

Add
Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

This Big 3 Kit features HyperFlex cable and comes with everything you need to upgrade your factory power and ground wire.

$141.83

Add

Don't see the accessory you're looking for?
View all available accessories for the Renegade + U.S. Amps Amplifier and Speaker Bundle.

Get FAST answers from customers ASK a Question See questions answers

Renegade Speakers and U.S. Amps Amplifier Bundle

This Sonic Electronix Exclusive offer showcases 2 sets of 5-1/4" Renegade RX52 2-Way RX series coaxial car speakers. These speakers are individually rated at 80 watts RMS, and 160 watts RMS per pair, giving you 320 watts RMS for all four speakers. The speakers feature a Polypropylene cone woofer and Butyl rubber surround for rigidity and optimum performance. These full range speakers also feature a 5/8" dome tweeter for enhanced highs. With a 4 Ohm impedance, and high temperature voice coil, these speakers are great if you are looking to improve that factory installed sound in your vehicle.

In order to provide the sufficient power to the RX Series speakers, this bundle will also include a U.S. Amps XA-800.4 4-Channel XA Series Amplifier. This amplifier is rated at 60 watts x 4 Chan. @ 4 Ohms, 85 watts x 4 Chan. @ 2 ohms, and 160 watts x 2 Chan. @ 4 Ohms bridged. The amplifier features a 2-Way System Protection Circuitry for added security and peace of mind that your amplifier will protect from any unforeseen events. While the variable high and low pass filters will allow complete control of your music frequencies for fine tuning and desired preferences. In addition this bundle will include a complete 8 gauge amplifier kit with RCA interconnect cables for complete installation. As an added bonus, we threw in two pairs of Street Wires ZN1250 Interconnect cables for a matching connection for FREE! In order to increase the overall sound quality and output from your system, this bundle also includes four 10" x 10" pieces of butyl sound dampening material. The sound damp will reduce road noise, vibrations and rattles that diminish the sound quality of your car audio system. This bundles has everything you need to take your factory sound and make it a sound all your own.

Renegade RX52 Features:
  • 2 Sets of 5-1/4" RX Series 2-Way Car Speakers
  • Power Handling:
    • Peak: 320 watts per set / 160 watts each
    • RMS: 160 watts per set / 80 watts each
  • Polypropylene woofer cone
  • Butyl rubber surround
  • 5/8" Dome tweeter
  • 4 ohms impedance
  • High temperature voice coil
  • Top-mount depth: 2-1/8"
  • Frequency response: 65-20,000 Hz
  • Includes grilles
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
U.S. Amps XA-800.4 Features:
  • XA Series 4-Channel Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 60 watts x 4 chan.
    • 2 ohms: 85 watts x 4 chan.
    • Bridged, 4 ohms: 160 watts x 2 chan.
  • Max Power Rating:
    • 4 ohms: 120 watts x 4 chan.
    • 2 ohms: 190 watts x 4 chan.
    • Bridged, 4 ohms: 380 watts x 2 chan.
  • Max power output: 380 watts x 1 chan.
  • MOSFET power supply
  • LED power (green) and protect (red) indicators
  • Variable Bass Boost (0 to +12 dB bass boost at 50 Hz)
  • 4/3/2 channel operation
  • Pair of RCA outputs
  • 2-Way System Protection circuitry
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Input sensitivity:300mv-8v
  • Variable high-pass filter (50-250 Hz)
  • Variable low-pass filter (50-250 Hz)
  • Frequency response: 10-25,000 Hz
  • Dimensions: 11-13/16"L x 9-5/8"W x 2-1/4"H
  • 8-gauge power and ground wiring is required for installation.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
The Install Bay AK8 Features:
  • Complete 8 Gauge Amplifier Installation Kit for a full installation of an amp
  • Includes gold plated RCA interconnect cables
  • Designed by the manufacturer for systems up to 1000 watts max
  • Everything you need for an amplifier installation in one convenient package
  • 1-year Manufacturer's warranty
The Install Bay AK8 Includes:
  1. 17 ft. of 8AWG Blue power cable
  2. 3 ft. of Black ground cable
  3. 17 ft. of Clear blue RCA cable
  4. 25 ft. Speaker wire
  5. 17 ft. of Clear blue remote turn-on wire
  6. 1 AGU fuse holder + 40AMP AGU fuse
  7. 5/16" Gold ring terminal
  8. 1/4" Gold ring terminal
  9. #10 Gold spade terminal
  10. 4 Gold speaker terminals
  11. 3 Grommets
  12. 20 4" cable ties
Ballistic SSSK Speaker Kit Features:
  • Four 10" x 10" pieces of butyl sound dampening material
  • Increases bass output and enhances speaker quality
  • Eliminates speaker distortion, road noise, and rattle
  • Can also be used for doors, trunks, trunk lids, interior panels, floorboards, etc
  • Three-step easy installation
  • Dimensions: 10"L x 10"W
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
StreetWires ZN1250 Specifications:
  • As a special BONUS, these come FREE with this purchase!
  • 2 Pairs of Zero Noise ZN1 Series 2-Channel Interconnect Cable
  • Split-Tip connector pins attach firmly and maintain secure contact
  • Twisted pair construction keeps noise from your car's electrical system out
  • Sure grip molded body reinforces the entire connector assembly and is easy to engage or remove
  • Flexible jacket provides easy installation
  • Silver-Plated connectors offer excellent conductivity and protection from corrosion
  • Total fit collars provide uniform contact to ensure a strong fit
  • Color-Coded (black/red) bands for easy left and right identification
  • Cable Length: 16.4 ft. (5 Meters)
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

Front Speaker Specifications

Speaker Size
Refers to the size of the speaker measured in inches. Every vehicle has standard application sizes. Please use our vehicle fitment guide for your vehicle's specific speaker sizes if you do not know them.
5-1/4"
Design
The number of individual drivers in a car speaker. Speakers with 2 drivers are known as a 2-way, and 3 drivers are known as a 3-way. Component systems are often referred to as "separates" because the tweeter is not attached to the midwoofer (main speaker driver) and mounts separately in a location such as a door post. Component systems typically come with an external crossover so you can easily adjust the high and low frequencies sent to both the midwoofer and the tweeter. Center channel speakers are great for those looking to have surround sound in their vehicle.
2-way
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No
Tweeter Design
Designs such as cone, dome, semi-dome, balanced dome, and whizzer are most popular. Cone tweeters are simple, efficient and typically are the most reasonably priced. Dome tweeters are used in most home speakers, and provide a smoother and more accurate sound. Semi-dome design is one with a dome placed inside a cone. A Balanced dome driver is a semi-dome with equal reproduction area given the cone and dome portions of the driver. A whizzer tweeter is a separate tweeter cone driven by the voice coil of the woofer.
Dome
Tweeter Composition
Materials such as polypropylene, silk, cloth, and paper are the most common, where as many more recent tweeters are now manufactured with composites such as Aluminum, Titanium, Mylar, and other materials.

PEI is an acronym for "Polyetherimide" which is an amorphous, amber transparent, high-performance thermoplastic.

Aluminum
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Polypropylene
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Butyl Rubber
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
160 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
80 watts
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
65 - 20,000 Hz
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
2-1/8"
Cutout Dimensions
Refers to the dimensions of the hole, measured in inches or millimeters, required to contain the speaker.
4-1/2" x 4-1/2" 
Speaker Grilles
A grating or screen of metal or plastic bars or wires, mounted in front of a speaker as protection. If yes, the speakers will include matching speaker grilles. If no, there are no grilles included.
Yes

Amplifier Power Specifications

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

60 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

85 watts x 4 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

Not Stable
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

160 watts x 2 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

380 watts x 2 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

760 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

320 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.05%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
High-Pass (HP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
90 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
40A x 1 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

NVX XKIT84 4-Channel 8-Gauge Wiring Kit

In case you didn't know, NVX has top notch wire and this kit has everything you need!

Your Price $69.99

Belva BAK84

Complete 8 Gauge Amplifier Wiring Kit with 4-Channel RCA Interconnects

Your Price $24.99

Five Piece Installer's Panel Removal Tool Kit

Helps with removing dash and trim panels during installation.

Your Price $11.99

Scosche TK12 Car Stereo Installation Kit

Includes panel removal tool, wire cutter/stripper, test light, RCA cable runner, screwdriver, and more!

Your Price $18.99

18 Butt Connectors, 2 Ring Terminals, and Zip Ties

Great for connecting your car stereo wires to the harness

Your Price $4.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

This Big 3 Kit features HyperFlex cable and comes with everything you need to upgrade your factory power and ground wire.

Your Price $141.83

XS Power BIG3XS 1/0 Gauge Big 3 Upgrade Kit

The XS Power Big 3 Kit features 100% OFC XP Flex cable and includes everything you need to upgrade your factory power and ground wire.

Your Price $92.52

XS Power BIG3XP 1/0 Gauge Big 3 Upgrade Kit

The Big 3 Kit comes with everything you need to upgrade your factory power and ground wire.

Your Price $49.99

Items we think you might want
AK8 main
InstallBay 8 Gauge Amp Kit (AK8)

• Complete 8 Gauge Amplifier Installation Kit with RCA Interconnect Cables
• 17ft. Blue Power Cable
• 3ft. Black Ground Cable
• 17ft. Blue RCA Cable
• 17ft. Blue Remote Turn-On Wire

Your Price $10.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

XA-800.4_2-RX52

Weight

22.89lbs

Internal SKU

xa8004_2-rx52

Internal Product ID

38227

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Renegade + U.S. Amps Amplifier and Speaker Bundle