Expert Service 1-877-289-7664 [Hours]

Fall Blow Out Dot Sale

1800W Alpine Subwoofer + Jensen Amplifier Bass Bundle

Alpine SWR-1043D 10" Type R Subwoofer + Jensen Power 900.1 Monoblock Amplifier + db Link Amp Kit

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Sonic Electronix Exclusive Alpine Bass Bundle Combo

This exclusive bass package includes one Alpine SWR-1043D 10" Dual 4-Ohm Type R Subwoofer, one Jensen Power 900.1 Class AB MonoBlock Amplifier, and one db Link 4-Gauge Power Amplifier Installation Kit. The 10" subwoofer has a peak power rating of 1800 watts and an RMS rating of 300-600 watts. It is constructed with a kevlar reinforced pulp cone and an injection molded santoprene rubber surround for ultimate performance. The Alpine Subwoofer has a Dual 4 Ohm Voice Coil; meant to be wired in parallel, to a final impedance of 2 Ohms. For more information regarding subwoofer wiring, please check out our Subwoofer Wiring Diagram

The Jensen amplifier is a perfect compliment to the Alpine subwoofer, it is equipped with 900 watts max, 450 watts @ 2 ohms, and 300 watts @ 4 ohms. This amplifier features LED indicators, Preamp RCA outputs, heavy duty heatsink, 3-way system protection circuitry, and much more. The InstallBay AK4 amp kit is the finishing touch to this incredible combo, it includes all the necessary wires/cables to provide generous amounts of power to the subwoofer and amplifier. Sonic Electronix is the only place you will find this one of a kind combo kit, enhance your sound system today.

Alpine SWR-1043D Features
  • 10" Dual 4 ohm Type R Subwoofer
  • Power Handling:
    • Peak: 1800 watts
    • RMS: 300-600 watts
  • Kevlar reinforced pulp cone woofer
  • 2-Piece Structural Parabolic diaphragm design
  • Injection molded Santoprene rubber surround
  • Alpine exclusive High Amplitude Multi-Roll (H.A.M.R) surround for impressive excursion and clean, accurate bass
  • FEA Optimized progressive NOMEX spider
  • Radial vented VC head sink
  • Concealed mount gasket system
  • Reinforced layer spider integration tinsel leads
  • Oversized 2-1/2" Voice coil
  • 4-Layer dual voice coil design
  • Voice coil made from 180°C high temperature wire on spiral cut aluminum former
  • Single-piece cast aluminum frame with Alpine Patent Pending Airflow Management System for efficient cooling
  • Airflow Management system controls the temperature of the voice coil by directing the air across the heatsink
  • One sided push terminals make installation and wiring fast and simple
  • Each terminal accepts up to 8 AWG wire for high power signal transfer
  • Concealed gasket mounting system hides the screw holes and makes for a clean install
  • Integrated grill technology allows for a seamless installation of a grill
  • US Patented Compound Radius Curve (CRC) design with integrated short sleeve configuration
  • CRC Machined motor structure creates a symmetrical magnetic field for less distortion and improves power handling
  • High-power, double-stacked strontium magnet structure
  • Newly redesigned for a 20% depth reduction
  • Frequency response: 26-400 Hz
  • Sensitivity: 83 dB
  • 1-year Sonic Electronix warranty
Jensen Power 900.1 Features
  • Monoblock Power Series Class AB Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 300 watts x 1 chan.
    • 2 ohms: 450 watts x 1 chan.
  • Max power output: 900 watts x 1 chan.
  • Pulse Width Modulated MOSFET power supply
  • Remote input level control with 5m cable
  • LED power (green) and standby/fault (red) indicators
  • Variable bass EQ (0-12 dB @ 45 Hz)
  • Soft Start Turn-on
  • Monoblock operation
  • Preamp RCA outputs to daisy chain multiple amps
  • 3-Way System Protection circuitry (thermal, DC-Offset, and speaker short protection)
  • Heavy duty extruded heatsink for extreme heat dissipation
  • High current bi-polar output transistors
  • Optimized class AB design minimizes distortion and reduces idle current
  • Chrome-plated RCA level inputs
  • Chrome-plated screw terminals
  • Variable Low-Pass Filter (40-300 Hz, 12 dB/octave)
  • Subsonic Filter (10-40 Hz @ 12 dB)
  • Signal-to-Noise Ratio: >100 dB
  • Frequency Response: 5-300 Hz
  • Variable Input Level: 400mV - 5V
  • THD (Total Harmonic Distortion): 0.02%
  • Fuse Rating: 2 x 30 amps
  • Dimensions: 9"D x 15-3/4"W x 2-1/2"H
  • 4-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
The InstallBay AK4
  • Complete 4 Gauge Amplifier Installation Kit
  • Designed specifically for car audio systems up to 1600 watts
  • Premium power and ground wire provides optimal power transfer
  • Made from 100% oxygen-free copper for a pure uninterrupted transfer of power
  • Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier
  • Includes everything that you need to install a single amplifier
  • Premium power and ground cable
  • 1-year Manufacturer's warranty
Package Includes:
  1. 17 ft. of Blue power cable
  2. 3 ft. of Black ground cable
  3. 17 ft. of Clear/blue RCA cable
  4. 25 ft. of Speaker wire
  5. 17 ft. of Remote turn-on wire
  6. In-line AGU fuse holder
  7. 60 Amp AGU fuse
  8. Installation hardware

Amplifier Power Specifications

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
300 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
450 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage. Often times this maximum is achieved during a brief musical burst, such as a drum accent or low bass hit. Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. This is the peak power output for the amplifier's 5th channel.
900 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

900 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

450 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
Not Bridgeable
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.02%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

40 - 300 Hz
Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
10 - 40 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
>100 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
30A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
1
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
600 watts
Total RMS Power Handling
This is the total RMS power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
600 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1800 watts
Total Peak Power Handling
This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
1800 watts
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Santoprene Rubber
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Kevlar Fiber
Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.5 cubic feet
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.0 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.8 cubic feet
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.5 cubic feet
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
83 dB
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
26 - 400 Hz
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
20 mm
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
6"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
9-1/16"
Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Sealed
Compatible Vehicle Make and Model
The model of vehicle that this vehicle specific product is designed for. Please keep in mind that engine variations can affect the compatibility of the products.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0
Henry

Phoenix, Az

Overall
Durability
Value
Features
Design
Usability
1800W Alpine Subwoofer + Jensen Amplifier Bass Bundle

January 17, 2012

I ordered this kit on Friday Jan 13th 2012 and received it on Saturday Jan 14th. These guys are incredible with shipping! The boxes was very well packed inside a larger box filled with shipping peanuts. I had the chance to install this the same day since it came very early. The sub sounds amazing, I think the Amp and Sub combo were very well paired together. I installed this in my 2007 A4 with a custom side mounted box for the trunk. The bass is smooth and crisp with no distortion. The fact that you can wire the sub control in reach of the driver seat is also convinant. I listen to a plethora of different types of music, and when I want the bass up or down it's just a reach away with a few clicks to the perfect setting. Will defiantly be buying from this company in the future. Good job guys.

2 of 2 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

XS Power BIG3XP 1/0 Gauge Big 3 Upgrade Kit

The Big 3 Kit comes with everything you need to upgrade your factory power and ground wire.

Your Price $49.99

XS Power BIG3XS 1/0 Gauge Big 3 Upgrade Kit

The XS Power Big 3 Kit features 100% OFC XP Flex cable and includes everything you need to upgrade your factory power and ground wire.

Your Price $99.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

This Big 3 Kit features HyperFlex cable and comes with everything you need to upgrade your factory power and ground wire.

Your Price $149.99

NVX Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Big 3 Upgrade Kit 1/0 gauge with EnvyFlex cable, wire cutters, 2 battery and 4 ring terminals.

Your Price $128.59

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

SWR-1043D_Power 900.1

Weight

35.55lbs

Internal SKU

swr1043d_power9001

Internal Product ID

39462

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: 1800W Alpine Subwoofer + Jensen Amplifier Bass Bundle

  • Subwoofer Size Buying Guide
  • How to Install a Car Amplifier