Expert Service 1-877-289-7664 [Hours]

Boom. SUBTEMBER is here!

Cerwin-Vega Stroker 800.4 (STKR800.4)

800W Stroker Series 4-Channel Class A/B Car Amplifier

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Cerwin Vega Audio Store

The Power of Stroker

The award winning Stroker series is back with its new line of amplifiers. The 800 watt 4-channel boasts a full range class AB topology and the Vega bass equalization circuit for the best low frequency reproduction. The amplifier also features a new high density alloy heatsink design which provides optimum thermal protection. Combined with the Recovering Thermal Management System (RTMS), this amplifier will run efficiently and at cool temperatures. This amplifier is perfect for anyone looking for high performance and consistent quality.

General Features:

  • Stroker Series 4-Channel Class AB Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 125 watts x 4 chan.
    • 2 ohms: 200 watts x 4 chan.
    • Bridged 4 ohms: 400 watts x 2 Chan.
  • Max power output: 400 watts x 4 chan.
  • Pulse Width Modulated MOSFET power supply
  • Clip indication LED's for simple amplifier system set-up
  • Variable Vega Bass Boost (0 to +15dB bass boost at 50 Hz)
  • New high density alloy heatsink design provides superior thermal management
  • (VSSF) Variable Sub-Sonic Filtering fixed at 18dB for maximum low frequency output reproduction
  • (RTMS) Recovering Thermal Management System, which monitors internal thermal temperature by briefly rolling back amplifier output when overheating occurs
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Variable high-pass filter (40-250Hz, 24 dB/octave)
  • Variable low-pass filter (40-250Hz, 24 dB/octave)
  • Subsonic filter (18dB at 15 Hz)
  • CEA-2006 compliant amplifier
  • Frequency response: 50-250Hz
  • 4 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
  • Dimensions: 8-9/10"W x 17-8/10"D x 2-1/10"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Product History:

Cerwin-Vega STKR800.4 thumbnail
(newest, current model)
Cerwin-Vega S8004 thumbnail
(previous model, replaced by Cerwin-Vega Stroker 800.4 (STKR800.4))

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

125 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

200 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

400 watts x 2 channels

Amplifier Specifications

Amplifier Series
This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

800 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.2%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
80 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
40A x 3 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes
Strappable
Some amplifiers can be "strapped" together in order to increase the output of a single audio channel. These amplifiers feature RCA preamp outputs, allowing you to pass the signal directly from one amp to the other to ensure consistency.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
100%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
4.0
Features
4.0
Design
5.0
Usability
3.0
Sam Watts

Canada

Overall
Durability
Value
Features
Design
Usability
Unimpressed

August 14, 2013

Bought this amp to run two sets of RE Audio xxx component sets and I must say even with the gains set with an oscope and the tuning done near perfect, I was still unable to get the type of power I was expecting from this amp. At high volumes the tweeters die down and the amp goes into protect after 15-20 minutes of solid play. OFC high strand 4gauge knu knoceptz wire, and OFC 10 gauge speaker wire still could not get the job done well. Amp also heated up very quickly. I will not recommend this amp to anyone looking for the screaming loud. HOWEVER, if youre running a small SQ setup this amp may be for you. I did enjoy sonics regular fast processing and the price was right. Just not the amp for me. I must say I expected more from cerwin vegas high end 4channel amplifier.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XKIT44 4-Gauge 4-Channel Wiring Kit

4-Channel 100% OFC Complete True 4 Gauge Amp Kit with RCA Cables and Speaker Wire

Your Price $99.99

T-Spec V8-4DAK 4-Channel 4-Gauge Wiring Kit

Get everything you need to hook up your new amplifier!

Your Price $89.95

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $59.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

Your Price $7.99

Small Universal Remote Level Bass Control

The Scosche RLC is a smaller universal bass remote that connects via RCA inputs.

Your Price $11.99

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIX45 X-Series RCA Interconnect Cable

16.4 ft. of 4-Channel X-Series RCA Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $34.99

StreetWires ZN9 Series Interconnect Cable

16.4 ft. of 4-Channel RCA Cable with Rhodium-plated contacts and ZeroNoise construction for clear signal transfer!

Your Price $99.95

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1250 Speaker Wire

50 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $29.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

SMD DD-1 Distortion Detector

Set the gain of an audio amplifier quickly and accurately

Your Price $149.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

XIX2025 Strapping RCA

0.25 Meter (0.86 ft) Hyper-Flex RCA cable w/ Serpentine-Cut Nickel Plated Connectors

Your Price $12.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

STKR800.4

UPC

660715403406

Weight

12.00lbs

Internal SKU

stkr8004

Internal Product ID

39674

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Cerwin-Vega Stroker 800.4 (STKR800.4)