Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Audiobahn A2150HCT

2400W Max, High Current 2-Channel Amplifier

Discontinued
|

We apologize

This item has been discontinued

  • 2400W Max, High-Current 2-Channel Car Amplifier
  • RMS Power Rating:
    • 150 watts x 2 chan. @ 4 ohms
    • 300 watts x 2 chan. @ 2 ohms
    • 450 watts x 2 chan. @ 1 ohm
    • Bridged:
      • 300 watts x 1 chan. @ 4 ohms
      • 600 watts x 1 chan. @ 2 ohms
      • 1200 watts x 1 chan. @ 1 ohm
  • Max Power Output: 2400 watts @ 1 ohm
  • Wired Remote Bass Level Control Included with Blue Illuminated Knobs
    • Also illuminates red to indicate when amplifier is clipping
  • High-Current, Non-Regulated Power Supply
  • Preamp Outputs
  • Cobalt Blue LED Illuminated Heat Sink Design (on/off switch for your preference)
  • Thermal Regulated, Air Induction Dual Cooling Fans
  • Double Sided PCB (Circuit Board)
  • High Gloss Chrome Plated Finish
  • Unique, Clean Chrome Fire/Flame Design
  • Blue Illuminated VU Meters Indicating Output Response
  • Clear Power and Speaker Connectors
  • Variable Bass Boost: 0-18dB @ 40-100Hz
  • Variable Low-Pass Crossover: 40-120Hz
  • Variable High-Pass Crossover: 50-750Hz
  • Variable Subsonic Filter: 20-50Hz
  • Signal-to-Noise Ratio: 100dB
  • Frequency Response: 10Hz-40kHz
  • THD: 0.05%
  • Channel Separation: 50dB
  • Input Sensitivity: 200mV - 8V
  • 4-gauge power and ground leads recommended. Contact us for information regarding a discount on a select amplifier kit when purchased together.
  • Dimensions: 15-7/8" L x 11-15/16" W x 2-1/2" H
    • Note: Flames add an additional 1" to the height
  • 1-year SonicElectronix.com warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

150 watts x 2 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

300 watts x 2 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

450 watts x 2 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

1200 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

2400 watts x 1 channels

Amplifier Specifications

Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
2
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

2400 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

1200 watts
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
1 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
1 ohm
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.05%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 750 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

40 - 120 Hz
Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
20 - 50 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
100 dB
Channel Separation
Also referred to as crosstalk. The amount of interference on one stereo channel caused by the leaking of the other stereo channel. The higher the rating in decibels (dB), the better the Channel Separation.
50 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
25A x 3 

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
4.8

Paul Vlieg

Charlotte ,North Carolina

Overall
Durability
Value
Features
Design
Usability

Still love this amp!

October 13, 2013

I bought this amp in 2006, to replace my soundstream reference 1000.it still works flawless.I've run my two 12s 1206t audiobahns on it the whole time. I've had to take it apart and solder line out because it was having issues,about a year ago,but i fixed it easily.the neons flicker now but an amp I've ran hard for 7 years,4 cars and 250000 mi. Its a great amp.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Impala-t

Florida

Overall
Durability
Value
Features
Design
Usability

Amazing amp

February 21, 2013

The best amp I have ever owned I've had it for 2 years and I have it cranked everyday keeps on going this is how amps should all be made. A lot of people have asked what the heck I have pushing my 15s and I tell them. Great product I'm upgrading and selling all to my brother

0 of 0 found this helpful

Help our customers find the most helpful reviews

craigmeyer

sheldon, ia

Overall
Durability
Value
Features
Design
Usability

a2150hct

October 16, 2012

I have had this amp for four years and three vehicles and four sets of subs on it. it will make anything pound, never overheats, barely even gets warm. only problem i have had with it is the lights are starting to burn out...overall a very strong, reliable amp

0 of 0 found this helpful

Help our customers find the most helpful reviews

stan the man

paducah

Overall
Durability
Value
Features
Design
Usability

the 2150 amp

January 1, 2012

I bought this amp over 5 years ago and it has never done me wrong. Down the highway for hours at a time pounding away never over heated no problems at all same system in 3 different autos. If she blows today i got my moneys worth lol.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

StreetWires FB0

1/0 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft 2-Channel RCA Audio Interconnect Cable with Twisted Pair Construction

Your Price $11.99

Kicker Q-Series RCA Interconnect Cable

16.5 ft. of 2-Channel Interconnects with twisted pair conductors, K-cut gold plated contacts, and hyper-flex technology for easy installation!

Your Price $32.95

NVX XIX25 X-Series Interconnect Cable

16.4 ft. of 4-Channel X-Series RCA Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $26.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

XIX2025 Strapping RCA

0.25 Meter (0.86 ft) Hyper-Flex RCA cable w/ Serpentine-Cut Nickel Plated Connectors

Your Price $12.99

Product Summary

Manufacturer

Model Number

A2150HCT

UPC

651718008729

Weight

23.00lbs

Internal SKU

a2150hct

Internal Product ID

59

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Audiobahn A2150HCT