Expert Service 1-661-257-9993 [Hours]

Clif Designs CDQ3X

3-way Active Crossover Network

We apologize

This item has been discontinued

Item Added to Cart

Clif Designs CDQ3X

3-way Active Crossover Network

$79.99

Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
$10.99
Add Warranty
3 years of protection

Get FAST answers from customers ASK a Question See questions answers

  • Frequency Response: 10 Hz - 30 kHz
  • Ground Loop Isolation Circuit
  • Front and Rear High Pass Frequency Adjustment
  • Front and Rear Output Level Control
  • Subwoofer Low Pass Frequency Adjustment
  • Subwoofer Bass Boost With Bass Frequency
  • Subwoofer Output Level Control
  • Remote Subwoofer Level Control
  • Remote Turn on Circuit
  • Power on LED with illuminated Clif Designs logo
  • Gold Plated Input/Output RCA Connectors
  • 200mV-2V Input Sensitivity
  • S/N Ration: >100dB
  • THD <0.01%
  • Subwoofer (Low-Pass)
  • Input Mix Switch (In, Out)
  • 30-300Hz Variable Frequency Control
  • 0-18dB Variable Bass Boost
  • 25-100 Hz Variable Bass Boost Frequency
  • Selectable 0 / 180Degree Phase Control
  • Independent Input Gain Control
  • Mid- Range (Mid-Pass)
  • 32-400 Hz Variable High Pass Crossover
  • Input Mix Switch (In, Out)
  • Independent Input Gain Control
  • Front & Rear High Pass
  • 32Hz - 400 Hz Variable Crossover
  • X1 or X20 Frequency Multiplier
  • Independent Input Gain Control
  • Dimensions: 7.55"L x 6.37"W x 1.81"H
  • 2-year Manufacturer's warranty

Crossover Specifications

Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

Equalizer Bands
The number of graphic or parametric equalizer bands the receiver has. The better the EQ, the more likely you will be able to "tweak" your sounds to your desire.
Built-in Bass Reconstruction
Bass reconstructors, or bass enhancers, improve low frequency reproduction in a car audio system with at least one subwoofer. These bass expander products will help your subs produce accurate bass thumps.
No
Line Driver
A line driver is a small amplifier used to support the strength of the audio signal coming from the source unit.
Button Color
Refers to the color of the physical buttons on the unit.
Blue
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
10 - 30,000 Hz
THD (Total Harmonic Distortion)
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.01%
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
100 dB
Width
The width of the item from left to right (side-to-side) measured in inches.
6-3/8"
Height
The height of the item, measured from top to bottom, in inches.
1-3/4"
Depth
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
7-1/2"

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

CDQ3X

UPC

784620016930

Weight

5.00lbs

Internal SKU

cdq3x

Internal Product ID

6323

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Clif Designs CDQ3X