Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale- more products added!

NVX VCW102 w/ FREE Speaker Wire!

10" Dual 2-ohm VC Series Car Subwoofer + 25 ft. of Speaker Wire!

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Amazing Bass for the Masses

NVX's VC-Series car subwoofers are about to blow you away. The VCW102 is a jack-of-all-trades and has been engineered to the highest standards. The woven fiber pressed paper cone and custom High Roll foam surround with Nylon stitching help reproduce tight and accurate bass, keeping cone distortion to a minimum even at the highest volume levels. The next key components in the design of the VCW102 are the large dual 2-1/2" High Temperature Aluminum voice coils and triple stacked motor structure. With all of these features combined this sub can handle some serious power at 600-750 watts RMS. The dual voice coils also give you many options for different Ohm load wiring configurations. This is a subwoofer designed with SPL and SQ in mind so you can have the best of both worlds.

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
VC (NVX)
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1500 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
750 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
2 ohms
Voice Coil Diameter
Diameter of voice coil, usually measured in inches.
2.5"
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
20 - 200 Hz
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
83 dB
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
20 mm
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Round / Circle
Main Cone Color
This is the color of the speaker's or subwoofer's cone.
Dark Gray
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Non-Pressed Paper With Woven Carbon Fiber Top
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Foam
Magnet Structure
Defines the overall structure of the subwoofers magnet.
Triple Stacked
Subwoofer Grille
Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
No
Re-Cone Kit Available
Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
No

Recommended Enclosure Specifications

Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Sealed
Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
.50 cubic feet
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.00 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.0 cubic feet
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.5 cubic feet
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
6"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
9.61"
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No

Electromechanical Parameters

Free-Air Resonance (Fs)
The free-air resonance frequency of the subwoofer, measured in Hz. At this frequency the weight of the moving parts is perfectly balanced with the subwoofers suspension system.
29 Hz
Equivalent Compliance (Vas)
This is the amount of air that has the same stiffness as the subwoofers suspension. The greater the rating, the lower the stiffness and larger recommended enclosure. It is measured in Liters.
24.96 liters
Total Speaker Q Value (Qts)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including all dimensionless losses. Essentially, a high Qts value (closer to 1.0) means the subwoofer is great for sealed enclosures and a low Qts value (closer to 0) means the woofer is great in vented enclosures. A Qts of around 0.45 means the woofer will work decently in either enclosure type.
0.41
Electrical Q Value (Qes)
The subwoofers relative damping (Q) at the resonance frequency (Fs), including electrical losses. Also called the mechanical damping of the subwoofer. The unitless measurement usually varies from 0.5 10.
0.477
Electrical Resistance of Voice Coil (Re)
Amount of DC resistance of the subwoofer when measured with an ohm meter. Typically, this will read less than the impedance rating of the subwoofer.
3.2 ohms
Mechanical Q Value (Qms)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including mechanical losses. Also called the mechanical damping of the subwoofer. This unitless measurement usually varies from 0.5 10.
3.012

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Sonic Electronix

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0

blakeracer

wichita, KS

Overall
Durability
Value
Features
Design
Usability

Excellent! Unreal quality, must have

November 12, 2012

NVX has the best quality, probably the best cone & surround material I have looked at IMO. I replaced my Kicker CVR104's for these newer brand subs. NVX quality & craftsmanship has impressed me ever since I purchased some of thier rca audio cables recently. I put these in my '12 Tacoma double cab with limited back space and RMS capability/mounting depth/box space. Paired the subs with a Rockford Fosgate T1000 @ 2ohm load. The end result is fantastic!! These are SUPER accurate while being more loud than I could've imagined. There is SO MUCH force with these I had to secure the box to the backwall so the subs/sub box didn't run away from vibrating so much!! I did alot of tinkering & there were plenty of times I felt that I was going to damage or puncture the surround, it is an extremely flexible strong material. NVX really hit the ball out of the park, High rms rating with limited space is just fantastic! I am absolutley exstatic for my purchase & I wish NVX the best~

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

Single 10" Subwoofer Angled Truck or Hatchback Box Enclosure

CARB Compliant, 5/8" MDF Shallow Sub Enclosure Lined with Polyfil.

Your Price $34.99

Single 10" Sealed MDF Subwoofer Enclosure

10-inch Sealed Car Sub Box Made with 3/4" MDF and lined w/ Polyfil.

Your Price $34.99

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

Your Price $39.99

25 ft. of Streetwires 12 Gauge Speaker Cable

You'll need speaker wire to hook up that new subwoofer!

Your Price $44.95

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

20 Square Feet of Sound Dampening Material

NVX Sound dampening is thicker than competitors, eliminates rattles and gives you bigger bass!

Your Price $59.99

Dynamat Sound Dampening Trunk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $109.95

Stinger Sound Dampening Trunk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for your whole trunk!

Your Price $69.99

12 oz. Can of Adhesive Spray

Spray adhesive used for adhering carpet to subwoofer boxes without bubbles.

Your Price $6.99

Spring Post Terminal Cup

Makes adding a spring post terminal to an enclosure simple! Banana clip ready!

Your Price $3.99

40" x 15 Ft Piece of Premium Un-Backed Automotive Trim Carpet

Durable design for long life-span, available in many colors and shades.

Your Price $39.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $3.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Xscorpion 9-Piece Nylon Plastic Pry and Chisel Tool Set

Easily removes dash/trims, door clips, panels and pins, rubber grommets and vehicle emblems.

Your Price $14.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $79.99

4 Ft of 1/4" Thick Black Heat Shrink Tubing

Provides abrasion resistance and added protection for your cables.

Your Price $3.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $8.99

Universal 10" Subwoofer Grille

Keep your subwoofer safe from accidental damages with this amazing grill.

Your Price $13.99

10" Protective Waffle Subwoofer Grille

Keep your subwoofer looking amazing while keeping it safe.

Your Price $4.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

AutoSound 2000 CD-101

Low frequency test CD

Your Price $11.99

Impedance Meter / Signal Generator

Easy to locate tuning frequencies of passive radiators and ported enclosures

Your Price $299.99

1 NVX VCW102 w/ FREE Speaker Wire! Subwoofer

Mono Amp

Mono Amp - Option 1

2 Channel Amp - Bridged

2 NVX VCW102 w/ FREE Speaker Wire! Subwoofers

Mono Amp

2 Channel Amp

4 Channel Amp - Bridged

3 NVX VCW102 w/ FREE Speaker Wire! Subwoofers

Mono Amp

Mono Amp - Option 1

4 Channel Amp

4 NVX VCW102 w/ FREE Speaker Wire! Subwoofers

2 Channel Amp

4 Channel Amp

Product Summary

Manufacturer

Model Number

VCW102_XWS1225

Weight

20.68lbs

Internal SKU

vcw102-xws1225

Internal Product ID

63959

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: NVX VCW102 w/ FREE Speaker Wire!