Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Boss MR120

Marine 12" Single 4 ohms Boat Subwoofer with Grill (AVA-MR120W, AVA-MR120 White)

Discontinued
|

We apologize

This item has been discontinued

Product Features:
  • 12" Single 4 Ohms Marine Subwoofer
  • Power Handling:
    • Peak: 800 watts
    • RMS: 400 watts
  • Impedance: Single 4 ohms
  • Water-resistant construction
  • High quality poly injection cone
  • Butyl rubber surround
  • 80 oz. magnet structure
  • 4 Ohms impedance
  • 2.5" high temperature voice coil
  • Frequency response: 25Hz - 2.5kHz
  • Water-resistant grill included

Subwoofer Specifications

Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Round / Circle
Main Cone Color
This is the color of the speaker's or subwoofer's cone.
Black
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Single
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
800 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
400 watts
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Butyl Rubber
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Polypropylene
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
94 dB
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
25 - 2,500 Hz
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
5 mm
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
5-5/8"
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No
Subwoofer Grille
Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
Yes - Included
Re-Cone Kit Available
Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
No
Amplified or Non-Amplified
This indicates if the subwoofer comes with an amplifier installed as one unit or Non-amplified which requires an external amp to power the subwoofer
Non-Amplified

Warranty and Return Policy

Parts Warranty Duration
2 years
Labor Warranty Duration
2 years
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
50%
4 Star
50%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0

james

rancho cucamonga, ca

Overall
Durability
Value
Features
Design
Usability

sounds great

December 21, 2010

This is a great sub for the price. I installed it in my 18.5 foot boat and it hits hard. Great speaker and recommend it

0 of 0 found this helpful

Help our customers find the most helpful reviews

Yngvar

Norway

Overall
Durability
Value
Features
Design
Usability

Boss MR120

September 30, 2010

Mounted together with the amplifier Boss MR800. Deep great vibrations and sound in my boat. Perfect subs for a boat app 25 feet.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Product Summary

Manufacturer

Model Number

MR120

UPC

791489103756

Weight

12.00lbs

Internal SKU

mr120

Internal Product ID

7238

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Boss MR120