Expert Service 1-877-289-7664 [Hours]

Shipping Promo

Sony + JBL Sound System for Dodge Ram Trucks

Sony Mono and 4-Chan Amplifiers + 2 Slim JBL Subwoofers + Sony Speakers + Ram Truck Box + Wiring

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Sony XM-GS100

600W RMS Monoblock GS Series Class D Subwoofer Amplifier w/ 3-year warranty!
Quantity: 1


 

 

General Features:

  • Monoblock GS Series Class D Subwoofer Amplifier
  • RMS Power Rating:
    • 4 ohms: 330 watts x 1 chan.
    • 2 ohms: 600 watts x 1 chan.
  • Pulse Width Modulated MOSFET power supply
  • Wired remote bass level control included
  • LED power (green) and protect (red) indicators
  • Variable Bass Boost (0 to +12 dB bass boost at 50 Hz)
  • Soft start turn-on
  • Mono channel operation
  • Speaker-level (high-level) inputs with signal sensing for automatic turn-on
  • Preamp RCA outputs to daisy chain multiple amps
  • 3-way protection circuitry (thermal, overload, and speaker short protection)
  • Heavy duty aluminum alloy heat-sink for extreme heat dissipation
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Variable low-pass filter (50-300 Hz, 24 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 10-300 Hz
  • 8 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
  • Dimensions: 10-3/4"W x 8"D x 2-1/8"H
  • Authorized Internet Dealer
  • 3 Year Manufacturer's Warranty

Sony XM-GS400

320W 4-Channel GS Series Compact Car Amplifier w/ 3-year warranty!
Quantity: 1



 

 

General Features:

  • 4-Channel GS Series Compact Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 70 watts x 4 chan.
    • 2 ohms: 80 watts x 4 chan.
    • Bridged, 4 ohms: 160 watts x 2 chan.
  • Pulse Width Modulated MOSFET power supply
  • LED power (green) and protect (red) indicators
  • Variable Bass Boost (0 to +12 dB bass boost at 50 Hz)
  • Soft start turn-on
  • 4/3/2 channel operation
  • 3-way protection circuitry (thermal, overload, and speaker short protection)
  • Heavy duty aluminum alloy heat-sink for extreme heat dissipation
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Variable high-pass filter (50-300 Hz, 24 dB/octave)
  • Variable low-pass filter (50-300 Hz, 24 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 10-100,000 Hz
  • 8 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
  • Dimensions: 10-3/4"W x 8"D x 2-1/8"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

JBL MS-10SD2 Slim

500W 10" SLIM Series Shallow Mount Dual 2-ohm Subwoofer
Quantity: 2

General Features:

  • 10" Dual 2-ohm MS SLIM Series Subwoofer
  • Power Handling:
    • Peak: 1000 watts
    • RMS: 200-500 watts
  • Impedance: 2 ohms
  • Flat-piston polypropylene cone
  • Dual-roll laminated fabric surround
  • Progressive spider
  • Cast-aluminum frame
  • High-Q, wide-range sub-bass performance
  • 1.8" Voice coil
  • Frequency response: 34-800 Hz
  • Resonance Frequency (Fs): 46.4Hz
  • Top-mount depth: 2-3/8"
  • Sensitivity: 74 dB
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Sony XS-GS6920

6x9" 2-Way GS Series Coaxial Speakers w/ 3-year warranty!
Quantity: 1



 

 

General Features:

  • 6 x 9" 2-way GS Series Coaxial Car Speakers
  • Power Handling:
    • Peak: 800 watts per pair / 400 watts each
    • RMS: 240 watts per pair / 120 watts each
  • MRC (Mica Reinforced Cellular) fiber woofer cone material
  • Butyl rubber speaker surround
  • 1” Synthetic fabric dome tweeter
  • Integrated crossover
  • Adjustable tweeter positioning
  • Bi-amp speaker system
  • CEA-2031 compliant speakers
  • High energy Neodymium magnet motor structure
  • 4 ohms impedance
  • Frequency Response: 35-27,000 Hz
  • Top-mount Depth: 3-1/2"
  • Sensitivity: 89dB
  • Authorized Internet Dealer
  • 3 Year Manufacturer's Warranty

Priced Per Pair

Sony XS-GT1338F

5-1/4" 3-Way Coaxial Car Speakers
Quantity: 1

General Features:

  • 5-1/4" 3-Way Car Speakers
  • Power Handling:
    • Peak: 460 watts per pair / 230 watts each
    • RMS: 70 watts per pair / 35 watts each
  • Aramid-Reinforced Carbon Fiber (HOP) cone material
  • Treated Rubber-Coated Cloth speaker surround
  • 1" cone mid-tweeter design
  • 1/4" Mica-Reinforced Cellular tweeter design
  • Great as factory replacement speakers
  • High-temperature voice coil
  • Ferrite magnet motor structure
  • Includes speaker grilles and mounting accessories
  • 4 ohms impedance
  • Frequency Response: 60-24,000 Hz
  • Top-mount Depth: 1-13/16"
  • Sensitivity: 88dB
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Priced Per Pair





Have a Question about the Sony XS-GT1338F?

Ground Shaker ODG 2 10

10" Dual Sealed Subwoofer Enclosure for select 98-01 Dodge Ram Ext-Cab Trucks
Quantity: 1

 

General Features:

  • 10" Dual Sealed Dodge Truck Box
  • Designed for 1998-2001 Dodge Ram 1500 Extended Cab Truck
  • Subwoofer mounting depth: 5-1/2"
  • Durable 5/8" Medium-Density Fiberboard (MDF) Construction
  • Box volume: 1.80 cubic feet
  • Color: Gray
  • Dimensions: 10-1/2"TD 14-1/2"D x 43-1/4"W x 9-1/4"H
  • Authorized Internet Dealer

T-Spec V6-4DAK

4 Gauge V6 Series CCA Dual Amp Kit w/4-Channel RCA Cables for Systems up to 2000 Watts
Quantity: 1


General Features:

  • 4 Gauge V6 Series CCA Dual Amp Kit w/4-Channel RCA Cables for Systems up to 2000 Watts
  • CCA (Copper-clad aluminum) construction
  • High strand count for maximum flexibility
  • BC-5W2 marine compliant RCA, speaker, power and ground wire
  • Real brass fusing and distribution
  • Packaged in resealable retail polybags
  • Also found as: TSpec V64DAK
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

What's in the Box:

  • 17ft. V6 4 Gauge CCA multi-strand power wire
  • 3ft. V6 4 Gauge CCA multi-strand ground wire
  • 17ft. 18 Gauge CCA blue remote turn-on wire
  • 12ft. V6 12 Gauge CCA two-color speaker wire
  • Two 17ft. V6 noise rejecting woven coaxial RCA cable with precision molded ends and split tip
  • Proprietary V8 MINI ANL fuse holder with 60A fuse
  • 4 Gauge dual position black-plated solid brass ground lug
  • Three position black-plated solid brass distribution block with one 4 Gauge in/ two 8 Gauge out
  • Nickel Plated 4 Gauge seamed crimp ring terminals with 8.5mm hole, red boot connects at battery end, black boot at ground
  • 4 Gauge spade terminals, with red and black boots for amp connection
  • Miscellaneous connectors, terminals and wire ties

T-Spec V6RCA-172

17 Ft. (5.18m) V6 Series 2-Channel 2-Channel Woven RCA Audio Cable
Quantity: 1


General Features:

  • 17 Ft. (5.18m) V6 Series 2-Channel 2-Channel Woven RCA Audio Cable
  • Woven coaxial design for increased noise rejection
  • Ultra-flexible PVC blended jacket
  • High tolerance compact molded ABS end
  • Dual split tip for maximum contact area
  • Packaged in resealable retail polybag
  • Also found as: TSpec V6RCA172
  • Color: Red
  • Length: 17 Ft. (5.18m)
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Amplifier Power Specifications

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
330 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
600 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

1100 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

600 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
.01%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 300 Hz
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
30A x 2 

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
MS Slim (JBL)
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
2 ohms
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
200-500 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1000 watts
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Laminated Fabric
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Polypropylene
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
74 dB
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
34 - 800 Hz
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
6 mm
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
2-3/8"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
9"
Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Compatible Vehicle Make and Model
The model of vehicle that this vehicle specific product is designed for. Please keep in mind that engine variations can affect the compatibility of the products.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

XS Power BIG3XP 1/0 Gauge Big 3 Upgrade Kit

The Big 3 Kit comes with everything you need to upgrade your factory power and ground wire.

Your Price $49.99

XS Power BIG3XS 1/0 Gauge Big 3 Upgrade Kit

The XS Power Big 3 Kit features 100% OFC XP Flex cable and includes everything you need to upgrade your factory power and ground wire.

Your Price $99.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

This Big 3 Kit features HyperFlex cable and comes with everything you need to upgrade your factory power and ground wire.

Your Price $151.99

NVX Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Big 3 Upgrade Kit 1/0 gauge with EnvyFlex cable, wire cutters, 2 battery and 4 ring terminals.

Your Price $131.39

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

XM-GS100 XM-GS400 MS-10SD2 Slim ODG210

Weight

74.16lbs

Internal SKU

xmgs100_ms10sd2slim_odg210

Internal Product ID

73063

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Sony + JBL Sound System for Dodge Ram Trucks