Expert Service 1-877-289-7664 [Hours]

Fusion Electronics MS-DA51600

1600 Watt 5-Channel Class-D Marine Amplifier

Out of Stock - Backorder
|

List price $519.99

$449.99

with warranty

You Save: $70.00 (13.46%)

Add an Extended Warranty

Fast, Free Shipping

Within the US 48

60-Day Money-Back

Hassle Free Returns

Low Price Guarantee

Seen it for less? Click here

365-Day Coverage

Warranty assistance for a year

Get FAST answers from customers ASK a Question See questions answers

General Features:

  • 1600 Watt 5-Channel Class-D Marine Amplifier
  • Conformal coated PCBs - water resistant coating protects from salt, air, and moisture
  • RMS Power Rating:
    • 4 ohms: 80 watts x 4 chan. + 250 watts x 1 chan.
    • 2 ohms: 130 watts x 4 chan + 330 watts x 1 chan.
    • Bridged, 4 ohms: 250 watts x 2 Chan + 250 watts x 1 chan.
  • Peak Power Rating: 1600 Watts
  • Low Battery drain - Class-D technology
  • Bridgeable
  • Anti-corrosion gold plated terminals
  • 5-way Circuitry Proection
  • 1-Piece Die Cast Heat Sink
  • Signal-to-Noise: 95dB
  • Speaker level inputs
  • Bass Remote
  • Variable high-pass filter (32-320 Hz)
  • Variable low-pass filter (32-320 Hz)
  • Dimensions: 8.67"W x 13"L x 2.26"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

80 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

130 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

250 watts x 2 channels

Power Specifications - Subwoofer Channel

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
250 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
330 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
5
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

1600 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

850 watts
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

32 - 320 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
95 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Sonic Electronix

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

Stinger SI4617 4000 Series Interconnect Cable

17 ft. 6-Channel 4000 Series Audio Interconnect Cable

Your Price $41.99

StreetWires SCP1215BL - 12 AWG Speaker Wire

12 Gauge Wire - 15 ft. of Speaker Cable with Twisted Construction

Your Price $24.95

Car/Marine Audio Installation Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

MS-DA51600

UPC

878816005782

Weight

9.20lbs

Internal SKU

msda51600

Internal Product ID

81337

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Fusion Electronics MS-DA51600