Expert Service 1-877-289-7664 [Hours]

Boom. SUBTEMBER is here!

Fusion Electronics FM-504

500 Watt 4-Channel FM Series Marine Amplifier

Out of Stock - Backorder
|

List price $329.99

$239.99

with warranty

You Save: $90.00 (27.27%)

Add an Extended Warranty

Fast, Free Shipping

Within the US 48

60-Day Money-Back

Hassle Free Returns

Low Price Guarantee

Seen it for less? Click here

365-Day Coverage

Warranty assistance for a year

Get FAST answers from customers ASK a Question See questions answers

General Features:

  • FM Series 500 Watt 4-Channel Marine Amplifier
  • Conformal coated PCBs - water resistant coating protects from salt, air, and moisture
  • RMS Power Rating:
    • 4 ohms: 50 watts x 4 chan.
    • 2 ohms: 75 watts x 4 chan.
    • Bridged, 4 ohms: 150 watts x 2 chan.
  • Peak Power Rating: 500 Watts
  • Class AB Design
  • Variable Bass Boost (0 to +18 dB bass boost, at 45Hz)
  • Bridgeable
  • 4-channel or 2- channel operation
  • Anti-corrosion gold plated terminals
  • FURANTZ Heat-Sink Technology
  • F.I.S.T FUSION Intercooled Semi-Conductor Technology - removes heat efficiently from semi-conductors for low distortion and thermal stability
  • Signal-to-Noise: 95dB
  • Variable high-pass filter (40-600 Hz)
  • Variable low-pass filter (40-160 Hz)
  • Dimensions: 8.67"W x 13"L x 2.26"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

50 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

75 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

150 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

500 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

500 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

300 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

40 - 600 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

40 - 160 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
95 dB

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Sonic Electronix

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

NVX XKIT42

Complete 4 Gauge Amp Wiring Kit with RCA Interconnect Cables and Speaker Wire!

Your Price $69.99

The InstallBay AK4 by Metra

4 Gauge Amplifier Installation Kit with RCA Interconnect Cable

Your Price $22.99

Kicker K-Series RCA Interconnect Cable

19 ft. of 4-Channel RCA cable with dual twisted-pair conductors, hyper-flex technology, and gold plated contacts for maximum signal transfer!

Your Price $29.95

Kicker 4-Channel RCA Audio Interconnect Cable

4 Meters (13 ft.) 4-Channel K-Series RCA Audio Interconnect Cable

Your Price $19.95

StreetWires ZN7 RCA Interconnect Cable

16.4 ft. of 4-Channel RCA Cable with hyper twist construction, oxygen free copper, and precision machined tips.

Your Price $59.99

Monster Cable XLN 16 AWG Speaker Wire

16 Gauge Wire - 50 ft. of Dual Twist Speaker Cable with 4 Pairs of Speaker Terminals.

Your Price $29.95

StreetWires SCP1215BL - 12 AWG Speaker Wire

12 Gauge Wire - 15 ft. of Speaker Cable with Twisted Construction

Your Price $24.95

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

Car/Marine Audio Installation Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

FM-504

UPC

878816001197

Weight

9.00lbs

Internal SKU

fm504

Internal Product ID

81338

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Fusion Electronics FM-504