Expert Service 1-661-257-9993 [Hours]

1000 Watt High End Bass: JL Audio 12w3 Subwoofer + JBL Amp + 100% Copper Kit

JL Audio 12W3v3-2 500W 12" W3v3 Series Single 2 ohm Subwoofer + JBL GTO-501EZ Monoblock GTO Series Class D Car Amplifier + 100% Copper Amp Kit

We apologize

This item has been discontinued

Item Added to Cart

1000 Watt High End Bass: JL Audio 12w3 Subwoofer + JBL Amp + 100% Copper Kit

JL Audio 12W3v3-2 500W 12" W3v3 Series Single 2 ohm Subwoofer + JBL GTO-501EZ Monoblock GTO Series Class D Car Amplifier + 100% Copper Amp Kit

$412.47

Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
$50.99
Add Warranty
3 years of protection

XS Power XP750 Special Edition

12-Volt Deep Cycle AGM Power Cell with 750 Max Amps

$72.99

Add
40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

$97.99

Add
Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the 1000 Watt High End Bass: JL Audio 12w3 Subwoofer + JBL Amp + 100% Copper Kit.

Get FAST answers from customers ASK a Question See questions answers

JL Audio 12W3v3-2

500W RMS 12" W3v3 Series Single 2-Ohm Subwoofer
Quantity: 1

Product Features:


 

 

 

 

 

 

 

 
  • Not sure which model you're looking for?
    • Click here to compare!

  • 12" W3v3 Series Subwoofer Driver
  • Power Handling:
    • RMS: 500 watts
  • Recommended Power Range: 150 - 500 watts
  • Impedance: Single 2-Ohm
  • Injection-molded, mineral-filled polypropylene cone
  • Nitrile butadiene rubber surround
  • Stamped steel basket
  • Customization trim ring
  • Floating-cone attach method
  • Highly linear, DMA-Optimized motor system
  • Insert molded suspension, coil and terminal sub-assembly
  • Patented vented reinforcement collar (VRC®)
  • Elevated frame cooling design
  • Nickel plated brass spring terminals
  • Engineered lead-wire design and attachments
  • Black Steel-Mesh Grille Insert Available: JL Audio SGRU-12
  • Precision-built in USA at JL Audio’s Miramar, Florida factory
  • Mounting depth: 6.65 "
  • Cutout dimensions: 11.0625 "
  • Free Air Resonance (Fs): 27.97 Hz
  • Sensitivity: 87.15 dB
  • Xmax: 13.0 mm
  • Reference Efficiency (no): 0.3100%
  • Frequency response: ~22 ~ 200 Hz
  • Matching Amplifiers:
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Check out the JL Audio 12W3v3 Owner's Manual


JL Model Comparison
From entry level woofers to competition grade, JL has them all. Let us find which one works for you.

Model RMS Power Cone Material Surround Material Sensitivity (dB) Frequency Response Xmax (mm Terminals Made In America
W7 Series 500-1500 Watts Polypropylene Foam Overroll 82.7 - 86.3 15-250 Hz 19-32 Push Terminals
W6 Series 600 Watts Polypropylene Rubber 82.7 - 85.4 20-200 Hz 19 Push Terminals
W3 Series 150-600 Watts Polypropylene Rubber 80.5-87.90 20-250 Hz 8.89-15.5 Push Terminals
W1 Series 150-300 Watts Polypropylene Rubber 83.9-86.1 22-200 8-11 Push Terminals
W0 Series 300-500 Watts Polypropylene Foam 84-88.20 20-250 Hz 11.4-12.7 Push Terminals
WX Series 200 Watts Polypropylene Foam 86-87.17 22-250 Hz 10 Spade Terminals


JBL GTO-501EZ

Monoblock GTO Series Class D Car Amplifier
Quantity: 1

General Features:

  • Monoblock GTO Series Class D Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 350 watts x 1 chan.
    • 2 ohms: 500 watts x 1 chan.
  • Max power output: 770 watts x 1 chan.
  • LED power (green) and protect (red) indicators
  • Variable Bass Boost (0 to +12 dB bass boost at 50 Hz)
  • Soft start turn-on
  • Gain LED indicators for proper gain adjustment
  • Mono channel operation
  • Heavy duty aluminum alloy heat-sink
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Input sensitivity:
    • Low level: 125mV-5V
  • Variable low-pass filter (40-280 Hz, 24 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 10-280 Hz
  • 8 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
  • Dimensions: 8-7/16"W x 9-11/16"L x 2-5/8"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

NVX XKIT82

100% Copper, 2-Channel True Spec 8 Gauge Amplifier Installation Kit w/ RCA Interconnect and 40 ft Speaker Cable
Quantity: 1

General Features:

  • 8 Gauge 2-Channel X-Series Complete Amplifier Installation Kit
  • Designed specifically for car audio systems up to 600 watts RMS
  • Premium power and ground wire provides optimal power transfer
  • Made from silver-tinned 100% virgin copper for a pure uninterrupted transfer of power and signal
  • Audio Interconnect RCA cables are made with twisted-pair technology for noise reduction
  • Solid Brass and satin-chromed ANL/Mini-ANL Fuse holder offers ideal protection for high powered systems
  • True-to-Gauge cables/wires meet or exceed the industry standard of copper required for the gauge size
  • Strand Count: 735
  • BC-5W2 Compliant
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Kit includes:

  1. 20 ft. (6.1 meters) Frosted Blue 8 gauge power wire with seamless crimp ring terminal
  2. 3 ft. (.91 meters) Frosted Gray 8 gauge ground wire with seamless crimp ring terminal
  3. 20 ft. (6.1 meters) Clear 18 gauge remote lead wire
  4. 40 ft. (12.2 meters) Frosted Gray/Blue 16 gauge speaker wire
  5. One 16 ft. (5 meters) 2-channel twisted construction RCA interconnect Cable (NVX XIV25)
  6. One NVX XMANL04 ANL/Mini-ANL Fuse Holder with 60 amp Mini-ANL fuse
  7. One 5/16" black rubber firewall grommet
  8. Two 8 gauge spade terminals
  9. Two black 16 gauge nickel-plated spade lugs
  10. Three blue 16 gauge nickel-plated spade lugs
  11. One black 18 gauge spade terminal
  12. Two 18 gauge red butt connector
  13. Ten 4" black zip ties

Amplifier Power Specifications

RMS Power @ 4 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
350 watts x 1 channels
RMS Power @ 2 ohms
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
500 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage. Often times this maximum is achieved during a brief musical burst, such as a drum accent or low bass hit. Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. This is the peak power output for the amplifier's 5th channel.
770 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

770 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

500 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
1%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
No
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

40 - 280 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
80 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
25A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
W3v3 (JL Audio)
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
1
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Single
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
2 ohms
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
500 watts
Total RMS Power Handling
This is the total RMS power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
500 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1000 watts
Total Peak Power Handling
This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
1000 watts
Compatible Vehicle Make and Model
The model of vehicle that this vehicle specific product is designed for. Please keep in mind that engine variations can affect the compatibility of the products.

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Sonic Electronix

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

XS Power XP750 Special Edition

12-Volt Deep Cycle AGM Power Cell with 750 Max Amps

Your Price $72.99

40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

Your Price $97.99

Dynamat Sound Dampening Bulk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $159.99

Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

Your Price $88.86

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $34.99

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $69.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $18.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $74.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $7.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

12W3v3-2_GTO-501EZ_XKIT82

Weight

31.83lbs

Internal SKU

12w3v32_gto501ez_xkit82

Internal Product ID

86021

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: 1000 Watt High End Bass: JL Audio 12w3 Subwoofer + JBL Amp + 100% Copper Kit