Expert Service 1-661-257-9993 [Hours]

Infinity BassLink-OPEN BOX

200W 10" Class D Powered Subwoofer System

We apologize

This item has been discontinued

Item Added to Cart

Infinity BassLink-OPEN BOX

200W 10" Class D Powered Subwoofer System

$121.99

Keep Shopping

NVX SDTK20

Trunk Kit - 20 Square Feet of Sound Dampening Material (Five 18" x 32" Pieces)

$53.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Infinity BassLink-OPEN BOX.

Get FAST answers from customers ASK a Question See questions answers

USED

General Features

  • Powered 10" Subwoofer with 10" Passive Radiator
  • Built-in class D 200-watt amplifier
  • Wired volume control with 16-foot cable
  • Frequency response 20-120 Hz
  • Low-pass crossover variable from 50-120 Hz at 12 dB per octave
  • Speaker and line-level inputs
  • Phase switch
  • Bass boost adjusts from -6 dB to +3 dB at 40 Hz
  • 25-amp fuse
  • Auto turn-on with speaker-level inputs
  • Remote turn-on lead (12V) required for use with RCA inputs
  • 19' speaker-level input wires with plug-in harness included
  • 14-1/2"W x 13-3/8"H x 9-7/8"D (vertical mount); 14-1/2"W x 9-1/2"H x 15-3/16"D (horizontal mount)
  • Also referred to as the Infinity Bass Link Sub System
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

200 watts
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 120 Hz
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
-6 - +3 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
25A x 1 

Subwoofer Specifications

Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
100 watts
Total RMS Power Handling
This is the total RMS power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
100 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
200 watts
Total Peak Power Handling
This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
200 watts
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Reinforced Paper
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
50 - 120 Hz

Enclosure Specifications

Box Type
Represents the style of the enclosure. Be sure to purchase the appropriate enclosure type and internal volume that will be compatible with your subwoofer's recommendation.

Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.

Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.

Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
Sealed
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
1
Height
The height of the item, measured from top to bottom, in inches.
13-3/8"
Width
The width of the item from left to right (side-to-side) measured in inches.
14-1/2"
Depth
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
9-7/8"
Number of Terminals
The number of terminals the enclosure has. Each terminal represents 1 positive and 1 negative.
1
Box Exterior Color
The color of the enclosure's exterior/outer finish.
Black
Box Finish
The material used on the outside of the box. Most boxes are carpeted to prevent exterior scratches; however vinyl is popular as it can often be color-matched to a near exact look of your leather factory interior.
Paint

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

NVX SDTK20

Trunk Kit - 20 Square Feet of Sound Dampening Material (Five 18" x 32" Pieces)

Your Price $53.99

Dynamat Xtreme 20' Trunk Kit 19405

20 ft. Trunk Kit with (5) Dynamat Extreme 18" x 32" Pieces

Your Price $94.95

Boom Mat Damping Material (050210)

20.8 sq.ft Damping Material - (10 pk - 12-1/2" x 24" x 2mm )

Your Price $109.99

Browse 10 questions and 76 answers
Hide answersShow all answers | Sort by
Why did you choose this?
Sonic Electronix Store
Great brand at a great price. Easy to install. Saves space..
Daniel G on Dec 3, 2016
Had it before. Shit was so cash!
Alexander B on Nov 14, 2016
It's compact
Frank M on Nov 28, 2016
I am limited on the amount of space I have to lose. For the size and amount of space I have this should be perfect.
Sammantha P on Nov 5, 2016
I just purchased this autotek ata 1000.4 amp to power my (2) pairs of 2 way kicker 6x8 in my truck. I also bought an infinty basslink powered sub. My radio is a pioneer FH-X720BT. If I have to run 4 RCA wires to amp from pioneer how do I run rca to powered sub?
sootwasher on Apr 10, 2015
Infinity BASSLINK
Infinity BASSLINK
Autotek ATA1000.4
Autotek ATA1000.4
Best Answer: U cant amp thebass link it has its own power suply the rca have to come directly from the stereo the base link hooks up like if it was a amp
Reply (1) · Report · Victor A on Apr 10, 2015
· Add Answer · I Have This Question Too (2)
Good day,

I am planning to add sub woofer (Infinity bass link) to improved sound quality on my Bmw z3 roadaster. I already replaced my speakers with stage I upgrade.

Can I do this connection directly from the after maket HU to the sub woofer with out passing the stock amplifier?. Is their any installation instruction/Kit included when I will buy this sub woofer
jose c on Oct 8, 2014
Best Answer: Hello Jose,

Your OEM amplifier will have absolutely No relationship with installing the BASSLINK. IF your headunit has an available Preout, then that is all you will need from the headunit. Infinity does send literature with the BASSLINK, but being such a simple/traditional install it may be a bit vague. Below is a link to the instruction book. You will simply need no more than an 8 Gauge Amp Wiring Kit, like the Monster Cable MPC P200 BAP200, which will account for your RCA, Power/Ground, and Remote.

Manual ---> http://goo.gl/gHxv8E

Monster Cable MPC P200 BAP200
http://www.sonicelectronix.com/item_18352_Monster-Cable-MPC-P200-BAP200.html
Reply (2) · Report · Customer SStaff on Oct 8, 2014
· Add Answer · I Have This Question Too (1)
I have a box kind of like this but it has a wiring harness that goes with the amp and i dont know what wires go were? There is a yellw (?) a blue (remote) a green (?) and 2 black wires (i no 1 of them is ground) but dont know what they go for.
A shopper on May 8, 2015
Best Answer: What make and model is your amp/box combo?
Reply · Report · Zackary G on May 8, 2015
· Add Answer · I Have This Question Too (1)
WIll this fit under seat in crew cab 04 F350?
robert p on Oct 20, 2014
Best Answer: Hello Robert,

We do not have the dimensions for the area under the seat of a '04 Ford F350. Like all things car audio, you must measure the space yourself, and compare it to the dimensions of the BASSLINK.

14-1/2"W x 9-1/2"H x 15-3/16"D (horizontal mount) .
Reply · Report · Customer SStaff on Oct 21, 2014
· Add Answer · I Have This Question Too (1)
does this work well in the trunk of a car?
leonidas on Nov 24, 2014
Best Answer: Depends in what you are looking for. If you are trying to vibrate windows while you drive down the street, no this would not be good in the trunk of a car. If you are looking to add to the sound quality of your stereo system then yes, this will definitely do it. The seats will deaden the sound quality and overall loudness however the bass transmission will pass theu and give you a little bump inside heightening the quality of your listening experience. If your into high quality sound this is a great unit for the money, if you want to have the heavy bass everyone else hears while you dive down the street this is not the unit for you.
Reply · Report · John M on Nov 24, 2014
· Add Answer · I Have This Question Too (0)
will this fit behind the seat in a reg cab 2008 gmc sierra?
A shopper on Jul 16, 2015
Best Answer: If you can get 10 inches behind your seat you would be able to bolt the basslink to the cab wall
Reply · Report · antonio p on Jul 17, 2015
· Add Answer · I Have This Question Too (0)
If you don't have RCA jacks to plug into the input how do you do the input wires how do you install input wires if you don't have RCA RCA jacks?
A shopper on Mar 9, 2016
Best Answer: http://images.sonicelectronix.com/images/2508455/big/.jpg
You can purchase that, but the infinity bass link comes with the instructions and wiring harness to do the same thing. You basically tap the wires to your factory speaker wires it works just like RCA cables
Reply · Report · jest s on Mar 9, 2016
· Add Answer · I Have This Question Too (0)
I spliced into my 2011 wrangler soundbar speakers with the purple and green wires. It has power run to it and the red power light is on. its grounded. Im not getting any sound though. Do I need to install a remote on wire? I thought I heard the basslink will power itself from being connected to the speakers so I wouldnt need the remote on?
RyanP on Jan 25, 2015
Best Answer: As long as the wire run to it is 12 volt you should be fine, however, you do need 12v to the remote as well. You can put a jumper from the power to the remote to make it work however, if the power in the light bar you you tapped into is on all the time the amp will be on all the time. The light bar wires and circuit/fuse is probably not sufficient to run the Basslink safely for long periods of time as the wires may melt or blow the fuse. I would run a seperate heavier power wire.
Reply · Report · John M on Jan 26, 2015
· Add Answer · I Have This Question Too (0)
bought this unit for my old 2005 f150, I had an aftermarket sterio. I just bought a 2014 fi50 and I'm stuck with the factory deck because its so integrated. How do I hook this infinity up? it has high level inputs and RCAs where would I find a remote turn on lead?
gully on Sep 9, 2015
Best Answer: You just splice the speaker leaves wires to the rear speaker wires and the unit uses those for audio transmission as well as remote turn on/off.
Reply · Report · Matthew C on Sep 10, 2015
· Add Answer · I Have This Question Too (0)

Product Summary

Manufacturer

Model Number

BASSLINK

Weight

23.00lbs

Internal SKU

LS-basslink-OB

Internal Product ID

89778

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Infinity BassLink-OPEN BOX