Expert Service 1-877-289-7664 [Hours]

Spring Clearance - Dot Sale

2 Pack of Kicker CVR124 (07CVR124)

Pair of 12" Dual 4 ohm CompVR Series Car Subwoofers

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

  • Two 12" Dual 4 Ohm CompVR Series Subwoofers
  • Power Handling:
    • Peak: 1600 watts per pair / 800 watts each
    • RMS: 800 watts per pair / 400 watts each
  • Impedance: Dual 4 ohms
  • Inverted Structural Dome Polymineral Injection Molded Cone: Remains rigid, and lowers distortion
  • Rear Cone Brace: Offers unmatched strength and resistance to deformation
  • Ribbed Santoprene Surround for Linear Cone Motion
  • Silver-Coated Stamped Steel Basket
  • Stitched Surround: Ensures the cone and surround won't separate, even under the highest loads
  • High-temp Polyimide Film Voice Coil Former
  • Dual Ultra-Length Voice Coils
  • Perimeter Venting
  • Sleeved High-Power Tinsel Lead Wires
  • Spring Loaded Nickel-Plated Terminals
  • Other search terms: CVR12 4 ohms, CVR124, 07CVR12, 07CVR124, 07CVR 12" 4 ohm, CompVR 12", CVR 12", Comp VR 12"
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty
2011 Kicker Authorized Online Dealer and eBay Seller Find out more info about the 07CVR124 at our blog!

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
Comp-VR / CVR (Kicker)
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
800 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
400 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Voice Coil Diameter
Diameter of voice coil, usually measured in inches.
Frequency Response
The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
25 - 500 Hz
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
86.7 dB
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
12.64 mm
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Round / Circle
Main Cone Color
This is the color of the speaker's or subwoofer's cone.
Silver
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Injection Molded Polypropylene (IMPP)
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Santoprene Rubber
Magnet Structure
Defines the overall structure of the subwoofers magnet.
Subwoofer Grille
Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
Optional (Accessory required and sold separately)
Re-Cone Kit Available
Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
No

Recommended Enclosure Specifications

Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Sealed
Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.0 cubic feet
Optimum Sealed Box Volume
This value indicates the ideal sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
4.6 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.75 cubic feet
Optimum Ported Box Volume
This value indicates the ideal ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
2.25 cubic feet
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
6-3/16"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
11-1/8"
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No

Electromechanical Parameters

Free-Air Resonance (Fs)
The free-air resonance frequency of the subwoofer, measured in Hz. At this frequency the weight of the moving parts is perfectly balanced with the subwoofers suspension system.
Equivalent Compliance (Vas)
This is the amount of air that has the same stiffness as the subwoofers suspension. The greater the rating, the lower the stiffness and larger recommended enclosure. It is measured in Liters.
Total Speaker Q Value (Qts)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including all dimensionless losses. Essentially, a high Qts value (closer to 1.0) means the subwoofer is great for sealed enclosures and a low Qts value (closer to 0) means the woofer is great in vented enclosures. A Qts of around 0.45 means the woofer will work decently in either enclosure type.
Electrical Q Value (Qes)
The subwoofers relative damping (Q) at the resonance frequency (Fs), including electrical losses. Also called the mechanical damping of the subwoofer. The unitless measurement usually varies from 0.5 10.
Electrical Resistance of Voice Coil (Re)
Amount of DC resistance of the subwoofer when measured with an ohm meter. Typically, this will read less than the impedance rating of the subwoofer.
Mechanical Q Value (Qms)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including mechanical losses. Also called the mechanical damping of the subwoofer. This unitless measurement usually varies from 0.5 10.
Efficiency Bandwidth Product (EBP)
This number represents the trade off between having an efficient woofer and one with a wide bandwidth. To calculate this number, take the Fs and divide it by the Qes. If the number is below 50, the woofer is designed for a sealed enclosure only. If it's between 50-100 it can be used in either. Lastly, if it's greater than 100 it's designed for vented enclosures.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
66%
4 Star
29%
3 Star
6%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
4.5
Value
4.8
Features
4.5
Design
4.5
Usability
4.7
mario

Los Angeles, CA

Overall
Durability
Value
Features
Design
Usability
BIG bang for the BUCK! lol

November 14, 2011

I have 2 of these in a sealed box in my tahoe and they are amazing! these subs pound! They broke off the motor mounts on both my front windows lol. For this price i reccomend them to anyone wanting loud ass bass that turns heads anywhere you go. Just wish it hit a little better on the higher notes.

5 of 7 found this helpful

Was this review helpful to you?

Audio freak

Candler, NC

Overall
Durability
Value
Features
Design
Usability
Nice subs. Pretty loud

September 25, 2012

I had 2 of these in a ported box. I had them hooked to the kicker zx750.1 mono amp. (Great amp by the way) that amp is rated at like 900 watts max. Each of these subs are rated at 800 watts max each. I dont think thats true. Prolly more like 400 watt max each. Because the voice coils were burning after about 15 minutes of play when i had the zx750.1 at 3/4 gain. If the kicker wattage rating were true on these subs, they would have no problem running on the kicker zx750.1 amp with the gain all the way up. I think kicker should look into their rating charts for these subs. You can run 2 of these just fine on a 600 watt amp.

3 of 4 found this helpful

Was this review helpful to you?

Kris

Cincinnati, OH

Overall
Durability
Value
Features
Design
Usability
aweswome

September 14, 2011

Love my new Kickers really loud would buy again and again, great value.

3 of 4 found this helpful

Was this review helpful to you?

Trip

Fresno, CA

Overall
Durability
Value
Features
Design
Usability
Loud

April 3, 2011

I had two of these n a ported box wired @ 1 ohm with a 2000 watt performance tekniq amp n it pounded so hard.I always turned heads everywhere I went.would definitely recommend to n e 1 who loves deep loud bass

2 of 2 found this helpful

Was this review helpful to you?

Dylan

Australia

Overall
Durability
Value
Features
Design
Usability
good subs

August 5, 2012

Had two of them and they go really hard for the price!

2 of 3 found this helpful

Was this review helpful to you?

Whiskey man

Nc

Overall
Durability
Value
Features
Design
Usability
Cvr's under rated power

March 12, 2012

I have two of these rated at 800 watts a piece. Thats 1600 watts total. I have the kicker 750 rms amp. Thats 1500 watts total coming from the amp. I had the gain at half way and the bass db knob 3/4 of the way up and my cvr's started burning. Great amp but sucky ratings on the subs. More like 1000 watts peak on two cvr 12's.

1 of 1 found this helpful

Was this review helpful to you?

Trae

Summerdale, AL

Overall
Durability
Value
Features
Design
Usability
Pretty nasty for the price!

August 30, 2011

My cousin traded his Solobaric 12's and some cash for 3 these because he didnt want that much boom anymore, but ofcourse he regreted it a few months later! Not because these werent excellent woofers, but he just missed the performance of the Solo's! Haha... anywho, they get low notes very well, but not so much the higher ones. There are definately much better SQ subs out there, but if you're looking for some good knock without payin a lot, these are the subs for you! An excellent set of woofers! A+

2 of 3 found this helpful

Was this review helpful to you?

Rodriguez

United States

Overall
Durability
Value
Features
Design
Usability
Great

June 10, 2011

These subs are terrific so far.. But I have a question?? When they are brand new are they supposed to get hot????

3 of 5 found this helpful

Was this review helpful to you?

cordell

west lafayette, IN

Overall
Durability
Value
Features
Design
Usability
CVR'S

May 27, 2011

I had these subs for about 3 yrs already in they broke almost everything on my car windows, handles you name it been broken, I love Kickers. Never been disappointed. For this price i couldn't pass it up so I bought two more pairs in my truck in wow! Crazy

3 of 5 found this helpful

Was this review helpful to you?

andrew

sacramento, CA

Overall
Durability
Value
Features
Design
Usability
15 comps in a ported box are louder

September 8, 2010

My friend had two of these in a sealed box on 400 rms each infinity power and they sounded pretty decent in a mustang. It lacked the low frequencies tho. I built my system with 2 15" kicker comps in a a custom box to kickers specs and running on kicker power in a hatchback acura integra. The 15" comps are louder with the right box and the right amp. I also have 2 12" l5s in a ported box on 1000 rms each and they are way louder than the cvrs maybe twice as loud in an suv. The comps are a lot closer than the cvrs in the right box. I know on paper this does not make sense but is very true. If you get these, put them in the right box or you are wasting money. I love kicker subs and amps but the subs are very picky about their enclosures.

0 of 0 found this helpful

Was this review helpful to you?

RASDOMIN

Murfreesboro, TN

Overall
Durability
Value
Features
Design
Usability
Great

August 18, 2010

I've had these speakers for 2 weeks so far, and when powered right they bang. They are great for someone who wants great bass for a reasonable price; but if your a bass freak that wants the car to fall apart or atleast feel like it I suggest you look into either some 15's or some more powerful kickers like the 2010 cvx or some L7's. Overall I give it 5 stars because for a first time subwoofer buyer I am more than satisfied.

0 of 0 found this helpful

Was this review helpful to you?

Brent

Clayton, NC

Overall
Durability
Value
Features
Design
Usability
Great Buy!

August 14, 2010

I would highly recommend these subs. They hit hard and clear. I had 2 of these in a 1999 F150 ext. cab in a ported box with a 1600 watt amp. They are by far the best deal for this price.

0 of 0 found this helpful

Was this review helpful to you?

SINCERE415

San Francisco, CA

Overall
Durability
Value
Features
Design
Usability
Looking for two 12"s that slap!!

July 20, 2010

I got these two in a sealed box with a mean machine 1200 into 1 ohm, these boy's are slapping so hard. You will not regret buying these. I've been sleeping on KICKER, not anymore. Very fast shipping as well.

0 of 0 found this helpful

Was this review helpful to you?

Kyle

hewitt, TX

Overall
Durability
Value
Features
Design
Usability
Best Ive Had !!!

May 29, 2010

I recently bought this product and put it in my ported box in my jeep. let just say my windows are flexing, my radar bounces up and down and my rear view mirror fell off i have it hooked up to a Hitron HPA2000.1D2000W Max, Pro Series Class D Monoblock. I recommend this product to every one

0 of 0 found this helpful

Was this review helpful to you?

Jmatt.

Vidalia,Georgia

Overall
Durability
Value
Features
Design
Usability
Pretty slamming system.

April 25, 2010

I have two of these in a ported box off of this site. I have them wired at 4 ohms. And they slam. I hit about 130 db. literally.

0 of 0 found this helpful

Was this review helpful to you?

Red

Williamstown, NJ

Overall
Durability
Value
Features
Design
Usability
Excellent

March 31, 2010

These subs are excellent, hands down. I was skeptical at first due to there low price but they hit hard...real hard. Crisp and clean bass I have them in a ported box. At half power with my ZX750 Kicker amp they are LOUD. I actually haven't put them over 75% power because its just ridiculous at that point (you can but it'll hurt hahaha) bottom line, awesome subs from a great company with an even better product guarantee and warranty. Definitely a buy!

0 of 0 found this helpful

Was this review helpful to you?

Made In The CSA

Enterprise, OR

Overall
Durability
Value
Features
Design
Usability
Great Deal!

March 30, 2010

These are the best bang for the buck no doubt! I have them in a bandpass box with 100 watts rms running to each (need to buy another amp but short on funds) they will make you def! I cant wait to see how hard they hit and how responsive they are with 200 watts rms (what they are rated for) running to each.

Lets put it this way with half the rated power running to them I blew 4 or the screw heads off the plexiglass to the front of my box and had to get grade 8 screws to keep it from popping them! THEY HIT HARD!

0 of 0 found this helpful

Was this review helpful to you?

Jo

Grand Rapids, MI

Overall
Durability
Value
Features
Design
Usability
Pretty Good

March 23, 2010

These subs are loud but they are better for the high bass notes. For the price they aren't beatable

0 of 0 found this helpful

Was this review helpful to you?

Bokalu

Clinton, NC

Overall
Durability
Value
Features
Design
Usability
WOW Loud Kickers

March 1, 2010

I Just bought these speakers all i can say is wow. they hit harder than my old db drive. And it was 2000 watts max and 1000 RMS.
Hurry Buy Now!!!!

0 of 0 found this helpful

Was this review helpful to you?

Devin

Maryville, TN

Overall
Durability
Value
Features
Design
Usability
subs are great

February 23, 2010

i bought these for a friend and they sound great
it's in an extended cap and they are very loud and durable

0 of 0 found this helpful

Was this review helpful to you?

Accessory Tools and Products

Accessories added

Single 12" Subwoofer Angled Truck or Hatchback Box Enclosure

CARB Compliant, 5/8" MDF Shallow Sub Enclosure Lined with Polyfil.

Your Price $29.99

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

Your Price $39.99

20 Ft. of Kicker 12 Gauge Speaker Wire

Get true gauge Kicker speaker wire to match your Kicker subwoofer!

Your Price $34.95

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

Your Price $119.99

Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

Your Price $99.99

12 oz. Can of Adhesive Spray

Spray adhesive used for adhering carpet to subwoofer boxes without bubbles.

Your Price $6.99

40" x 15 Ft Piece of Premium Un-Backed Automotive Trim Carpet

Durable design for long life-span, available in many colors and shades.

Your Price $39.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $1.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $16.99

Xscorpion 9-Piece Nylon Plastic Pry and Chisel Tool Set

Easily removes dash/trims, door clips, panels and pins, rubber grommets and vehicle emblems.

Your Price $14.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $79.99

4 Ft of 1/4" Thick Black Heat Shrink Tubing

Provides abrasion resistance and added protection for your cables.

Your Price $3.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $8.99

Kicker GR120

12" Speaker Grille for Kicker Subwoofers

Your Price $26.95

12" Protective Waffle Subwoofer Grille

Keep your subwoofer looking amazing while keeping it safe.

Your Price $4.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

1 2 Pack of Kicker CVR124 (07CVR124) Subwoofer

Mono Amp

2 Channel Amp - Bridged

2 2 Pack of Kicker CVR124 (07CVR124) Subwoofers

Mono Amp

Mono Amp - Option 1

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp - Bridged

3 2 Pack of Kicker CVR124 (07CVR124) Subwoofers

Mono Amp

4 Channel Amp

4 2 Pack of Kicker CVR124 (07CVR124) Subwoofers

Mono Amp

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

07CVR124-2-Pack

Weight

30.00lbs

Internal SKU

2subs_07cvr124

Internal Product ID

9347

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: 2 Pack of Kicker CVR124 (07CVR124)