Expert Service 1-877-289-7664 [Hours]

Cadence FXB12.2A

1200W Dual 12" FXB Series Amplified Subwoofer Enclosure

We apologize

This item has been discontinued

Item Added to Cart

Cadence FXB12.2A

1200W Dual 12" FXB Series Amplified Subwoofer Enclosure


Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
Add Warranty
3 years of protection


100% Copper, 2-Channel True Spec 8 Gauge Amplifier Installation Kit



Trunk Kit - 20 Square Feet of Sound Dampening Material (Five 18" x 32" Pieces)



Don't see the accessory you're looking for?
View all available accessories for the Cadence FXB12.2A.

Get FAST answers from customers ASK a Question See questions answers

Subwoofer Specification:

  • Dual 12" FXB Series Amplified Enclosure
  • Power Handling:
    • Peak: 1,200 watts
    • RMS: 600 watts
  • Frequency Response: 20 - 500Hz
  • Sensitivity: 90 dB
  • Damping @ 100Hz: >200
  • Subwoofer Cone: Ultra Stiff Kevlar Reinforced Paper
  • Subwoofer Surround: High Excursion Double Foam
  • Woven Fiber Glass w/ a Full Inverted Dust Cap
  • Quad Layer Conex Spider
  • 4 Layer Aluminum Voice Coil
  • Expanded and Rolled Steel Basket

Amplifier Specifications:

  • Class D Mono Block
  • Aluminum Extruded Chassis
  • Thermal, Overload, and Speaker Short Protection
  • Soft Delay Remote Turn-on Circuit
  • Variable Gain Control
  • Variable Low Pass Control
  • Remote Bass Control
  • Low Level & High Level Inputs
    • Input Voltage: 200mV - 8V
  • LED Power and Protection Indicators
  • Dimensions: 39-7/16"L x 18-1/8"W x 19-7/8"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Amplifier Power Specifications

RMS Power @ 1 ohm
The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far. If the final impedance of your speaker(s) or subwoofer(s) equals 1 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound. The 5th channel on these particular amplifiers are usually dedicated for driving subwoofers.
600 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage. Often times this maximum is achieved during a brief musical burst, such as a drum accent or low bass hit. Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison. This is the peak power output for the amplifier's 5th channel.
1200 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

1200 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

600 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
90 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.

Subwoofer Specifications

Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Kevlar Reinforced Semi-Pressed Paper
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Round / Circle

Enclosure Specifications

Box Type
Represents the style of the enclosure. Be sure to purchase the appropriate enclosure type and internal volume that will be compatible with your subwoofer's recommendation.

Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.

Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.

Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
Vented / Ported
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
Box Style/Shape
The box style or shape refers to the actual shape of the box. Square and rectangular boxes are straight-edged boxes on all sides, whereas hatchback and truck style enclosures feature an angled front or back design that allows for installation in places short on depth such as single cab pickup trucks. You can also use such enclosures in hatchback cars or other vehicles where space is a premium. Tube and cylinder shaped boxes were made popular by Bazooka and are a great option for those looking for a nice amount of bass without sacrificing lots of space. They may even fit in locations that slim truck boxes cannot fit in. If the enclosure is vehicle specific, we encourage you to read the product description to find out which vehicles the enclosure is made for.

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
4 Star
3 Star
2 Star
1 Star

Average Attribution Rating

Accessory Tools and Products

Accessories added


100% Copper, 2-Channel True Spec 8 Gauge Amplifier Installation Kit

Your Price $49.99

Belva BAK82BL

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Cable (CCA Wiring)

Your Price $12.99


Trunk Kit - 20 Square Feet of Sound Dampening Material (Five 18" x 32" Pieces)

Your Price $53.99

Dynamat Xtreme 20' Trunk Kit 19405

20 ft. Trunk Kit with (5) Dynamat Extreme 18" x 32" Pieces

Your Price $97.97

Boom Mat Damping Material (050210)

20.8 sq.ft Damping Material - (10 pk - 12-1/2" x 24" x 2mm )

Your Price $109.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary


Model Number






Internal SKU


Internal Product ID


Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Cadence FXB12.2A