Expert Service 1-661-257-9993 [Hours]

Audiopipe APVB-10ET OPEN BOX COMPLETE

Single 10" Vented Subwoofer Enclosure Loaded w/ TS-AR10 Subwoofer

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Audiopipe Car Audio Store

Subwoofer Features:

  • Item Condition: Open box complete
    • Item has been installed and used
    • 10" Single 4 ohm TS-AR Series Subwoofer
    • Power Handling:
      • Peak: 500 watts
      • RMS: 250 watts
    • Impedance: 4 ohms
    • Polypropylene cone
    • Large foam edge surround
    • Patented pipe multi-connect terminal
    • Powdered black paint steel basket
    • 2" 4-layer voice coil
    • 50oz. magnet motor structure
    • Frequency response: 32-400 Hz
    • Sensitivity: 101dB
    • Authorized Internet Dealer
    • 1-year Manufacturer's Warranty

    General Enclosure Features:

    • Vented enclosure
    • Durable dark gray carpet
    • High quality MDF construction
    • Subwoofer mounting depth: 5-7/8"
    • Subwoofer cutout diameter: 9-1/2"
    • Dimensions: 15.4"D x 13.2"W x 10.9"H

    Subwoofer Specifications

    Subwoofer Series
    Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
    Subwoofer Size
    Refers to the diameter of the subwoofer, measured in inches.
    Voice Coil(s)
    Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
    Impedance (Per Voice Coil)
    The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
    RMS Power Handling
    The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
    Total RMS Power Handling
    This is the total RMS power handling of all the subwoofers included in the package or enclosure.

    If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

    The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
    Peak Power Handling
    Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
    Total Peak Power Handling
    This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

    If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

    Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
    Woofer Composition
    Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
    Woofer Surround
    A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
    Sensitivity
    An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
     
    Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
    Frequency Response
    The range of frequencies the speaker will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
    Xmax (millimeters)
    Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
    Subwoofer Design
    This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

    Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

    Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

    Enclosure Specifications

    Box Type
    Represents the style of the enclosure. Be sure to purchase the appropriate enclosure type and internal volume that will be compatible with your subwoofer's recommendation.

    Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.

    Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.

    Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
    Number of Subs/Speakers
    This value represents the number of speakers or subwoofers that the enclosure accommodates.
    Box Style/Shape
    The box style or shape refers to the actual shape of the box. Square and rectangular boxes are straight-edged boxes on all sides, whereas hatchback and truck style enclosures feature an angled front or back design that allows for installation in places short on depth such as single cab pickup trucks. You can also use such enclosures in hatchback cars or other vehicles where space is a premium. Tube and cylinder shaped boxes were made popular by Bazooka and are a great option for those looking for a nice amount of bass without sacrificing lots of space. They may even fit in locations that slim truck boxes cannot fit in. If the enclosure is vehicle specific, we encourage you to read the product description to find out which vehicles the enclosure is made for.
    Height
    The height of the item, measured from top to bottom, in inches.
    Width
    The width of the item from left to right (side-to-side) measured in inches.
    Depth
    The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
    Second Depth
    The second depth is used only when the box is slanted or angled. This value is the top measurement and it is measured in inches.
    Wood Thickness
    The thickness of the wood the enclosure is made of, measured in inches.
    Number of Terminals
    The number of terminals the enclosure has. Each terminal represents 1 positive and 1 negative.
    Terminal Type
    Spring clip terminals work best with bare wire connections with small-gauge speaker wire, or pin-type connectors.

    Binding post terminals are a sturdier, more versatile type of speaker terminal. Because binding post terminals are are threaded, you can tighten them down against the wire or connector for a tight, clean connection. The most popular style of binding post terminals is known as a "5-way binding post". This type can accept bare wire, or any of the common speaker wire connectors. Binding posts with the option to be used with banana clips are even more versatile

    Spring posts are a hybrid of the two. Instead of using a thread and "screwing" them tight, they use a spring to allow the wire to fit and tighten against the terminal.

    Box Exterior Color
    The color of the enclosure's exterior/outer finish.
    Box Finish
    The material used on the outside of the box. Most boxes are carpeted to prevent exterior scratches; however vinyl is popular as it can often be color-matched to a near exact look of your leather factory interior.

    Specials with this Item

    Promotions
    Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

    Warranty and Return Policy

    Parts Warranty Duration
    1 year
    Labor Warranty Duration
    1 year
    Warranty Provider
    Manufacturer

    Summary of Customer Ratings & Reviews

    Rating Distribution

    5 Star
    0%
    4 Star
    0%
    3 Star
    0%
    2 Star
    0%
    1 Star
    0%

    Average Attribution Rating

    Durability
    0.0
    Value
    0.0
    Features
    0.0
    Design
    0.0
    Usability
    0.0
    Hide answersShow all answers | Sort by
    No questions have been asked about this item. Be the first!

    Product Summary

    Manufacturer

    Model Number

    LS-APVB-10ET-OBC

    Weight

    32.20lbs

    Internal SKU

    LS-apvb10et-OBCra216060

    Internal Product ID

    96277

    Sonic Electronix Wiring Guide

    Wiring Diagram Legend

    Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

    Product Name: Audiopipe APVB-10ET OPEN BOX COMPLETE