Kenwood 5-Channel or more Amps at Sonic Electronix

Kenwood 5-Channel or more Amps

Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
Kenwood KAC-M8005

5-Channel Marine Class-D Amplifier (800W RMS)

KAC-M8005 main
Go to item page

5-Channel Marine Class-D Amplifier (800W RMS)

• 50 Watts RMS x 4 @ 4 ohms + 300 watts x 1 chan.
• 75 Watts RMS x 4 @ 2 ohms + 500 watts x 1 chan.
• Bridged: 150 Watts RMS x 2 @ 4 ohms
• Total Peak Power: 1600 Watts
• CEA-2006 Compliant
• Variable high-pass filter: 50 - 200 Hz, 12dB/octave
• Variable low-pass filter: 50 - 200 Hz, 24 dB/octave (sub)
• Extruded Aluminum Heat Sink Design
• Dimensions: 9"W x 7 3/8"L x 2 3/16"H

Kenwood KAC-M8005

5-Channel Marine Class-D Amplifier (800W RMS)

In stock

$420.00 (4.76% off)
$399.99
Hide info
More info Item page
2 Special offers
  • 10% Off NVX Universal Bluetooth Controller with Purchase!
  • FREE 4 Gauge 5/6 Channel Wiring Kit with Select Amps!

Item Added to Cart

KAC-M8005 small

5-Channel Marine Class-D Amplifier (800W RMS)

$399.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add
NVX XIV65 V-Series Interconnect Cable

5m (16.40 ft) 6-Channel RCA Audio Interconnect Cable

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Kenwood KAC-M8005.
Kenwood KAC-D8105

1600 Watts Max Power 5-Channel Class D Amplifier

KAC-D8105 main
Go to item page

1600 Watts Max Power 5-Channel Class D Amplifier

• Kenwood KAC-D8105 5 Channel Amplifier
• Peak Power: 1600 watts
• 50 watts RMS x 4 + 300 watts at 4 Ohms
• 75 watts x4 + 500 watts at 2 Ohms
• Dimensions: 9"W x 2-3/16"H x 7-3/8"D

1
Kenwood KAC-D8105

1600 Watts Max Power 5-Channel Class D Amplifier

In stock

Only 1 Left!

$450.00 (22.22% off)
$349.99

Item Added to Cart

KAC-D8105 small

1600 Watts Max Power 5-Channel Class D Amplifier

$349.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XIV65 V-Series Interconnect Cable

5m (16.40 ft) 6-Channel RCA Audio Interconnect Cable

$34.99

Add
NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$29.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Kenwood KAC-D8105.
Kenwood eXcelon XR901-5

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included

XR901-5 main
Go to item page

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included

• 60 Watts x 4, 400W x Sub Channel RMS @ 4 ohms
• 75 Watts RMS x 4, 600W x Sub Channel @ 2 ohms
• Total Peak Power: 1800 Watts
• CEA-2006 Compliant
• Remote Bass Knob Included
• Heavy Duty Aluminum Heatsink
• Dimensions:10-1/4" W x 6-5/8" L x 1" H

Kenwood eXcelon XR901-5

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included

OUT OF STOCK

$650.00 (10.77% off)
$579.99

Item Added to Cart

XR901-5 small

1800W Max (900W RMS) XR Series 2-ohm Stable Class-D 5-Channel Amplifier w/ Bass Knob Included

$579.99

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
AudioControl LC6i (Black)

6 Channel Line Out Converter with Internal Summing & 5-year warranty*!

$149.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Kenwood eXcelon XR901-5.
Kenwood eXcelon X802-5

X Series 800W RMS 5-channel Class D Car Audio Amplifier

X802-5 main
Go to item page

X Series 800W RMS 5-channel Class D Car Audio Amplifier

• 50 Watts RMS x 4 + 300 x 1 @ 4 ohms
• 75 Watts RMS x 4 and 500 x 1 @ 2 ohms
• Bridged: 150 Watts x 2 chan. @ 4 ohms
• Total Peak Power: 1600 Watts
• CEA-2006 Compliant
• Frequency Response: 20 - 50000Hz
• Variable high-pass filter: 50 - 200 Hz, 12 dB/octave
• Variable low-pass filter: 50 - 200 Hz, 12 dB/octave
• Variable Bass Boost: 0 to +18 dB bass boost at 40 Hz

Kenwood eXcelon X802-5

X Series 800W RMS 5-channel Class D Car Audio Amplifier

OUT OF STOCK

$450.00 (22.22% off)
$349.99

Item Added to Cart

X802-5 small

X Series 800W RMS 5-channel Class D Car Audio Amplifier

$349.99

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Kenwood eXcelon X802-5.

Related Categories


Kenwood Marine Amplifiers Kenwood Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

    clear all items