MTX Mini Amps at Sonic Electronix

MTX Mini Amps

Their small form factor and ease of installation make MTX mini amps a popular product.
Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
MTX Audio THUNDER500.1

500W RMS Class D 1-Channel Monoblock Power Car Amplifier

THUNDER500.1 main
Go to item page

500W RMS Class D 1-Channel Monoblock Power Car Amplifier

• RMS: 300W x 1 @ 4 ohms, 500W x 1 @ 2 ohms
• Total Peak Power: 1000W
• 3-Way Protection Circuitry
• Selectable Bass Boost (0-6-12 dB)
• Class D Circuitry
• Dimensions: 6-5/16"W x 8-15/16"L x 2-1/4"H

10
MTX Audio THUNDER500.1

500W RMS Class D 1-Channel Monoblock Power Car Amplifier

In stock

$199.95 (10.00% off)
$179.95
Hide info
More info Item page
4 Special offers
  • 50% off a Belva Wiring Kit and Capacitor with Amp Purchase!
  • 50% Off a 4 Gauge Installation Kit with Purchase!
  • Add a Universal Bass Knob!
  • Get 20% off MTX Audio Bass Remote with Purchase!

Item Added to Cart

THUNDER500.1 small

500W RMS Class D 1-Channel Monoblock Power Car Amplifier

$179.95

Keep Shopping

Belva BAK42BK 4 Gauge Amplifier Installation Kit

Great amps need great wire at a great price. This amp kit has everything you need!

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$19.95

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio THUNDER500.1.
MTX Audio MUD100.2 2-Channel PowerSports Amplifier

400W Peak (200W RMS) 2-Channel Bridgeable Ultra-Compact Class D Power Sports Amplifier for Install in Car, Off-Road, SSV and more...

MUD100.2 main
Go to item page

400W Peak (200W RMS) 2-Channel Bridgeable Ultra-Compact Class D Power Sports Amplifier for Install in Car, Off-Road, SSV and more...

• RMS Power: 50W x 2 @ 4 ohms, 100W x 2 @ 2 ohms
• Total Peak Power: 400W
• Fixed HPF/LPF (80 Hz @ 12dB/Oct)
• Dimensions: 5.71"W x 1.61"L x 4.65"H

3
MTX Audio MUD100.2 2-Channel PowerSports Amplifier

400W Peak (200W RMS) 2-Channel Bridgeable Ultra-Compact Class D Power Sports Amplifier for Install in Car, Off-Road, SSV and more...

In stock

Only 3 Left!

$199.95 (10.00% off)
$179.95
Hide info
More info Item page
3 Special offers
  • Save 50% on an 8 Gauge Amp Kit with Purchase!
  • 50% Off NVX Universal Bluetooth Controller with Purchase!
  • Get 20% off an NVX Universal Remote Level Control

Item Added to Cart

MUD100.2 small

400W Peak (200W RMS) 2-Channel Bridgeable Ultra-Compact Class D Power Sports Amplifier for Install in Car, Off-Road, SSV and more...

$179.95

Keep Shopping

Belva BAK82

Complete 8 Gauge Amplifier Wiring Kit with 2-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio MUD100.2 2-Channel PowerSports Amplifier.
MTX Audio MUD100.4 4-Channel Power Sports Amplifier

400W RMS Bridgeable Ultra-Compact Amplifier for Car, Off-Road, SSV and more...

MUD100.4 main
Go to item page

400W RMS Bridgeable Ultra-Compact Amplifier for Car, Off-Road, SSV and more...

• 50 Watts RMS x 4 @ 4 ohms
• 100 Watts RMS x 4 @ 2 ohms
• Total Peak Power: 800 Watts
• Selectable Front high-pass filter: 80 / 200 Hz
• Speaker-level (high-level) inputs

1
MTX Audio MUD100.4 4-Channel Power Sports Amplifier

400W RMS Bridgeable Ultra-Compact Amplifier for Car, Off-Road, SSV and more...

In stock

$299.95 (16.67% off)
$249.95
Hide info
More info Item page
1 Special offer
  • 50% Off NVX Universal Bluetooth Controller with Purchase!

Item Added to Cart

MUD100.4 small

400W RMS Bridgeable Ultra-Compact Amplifier for Car, Off-Road, SSV and more...

$249.95

Keep Shopping

Belva BAK84

Complete 8 Gauge Amplifier Wiring Kit with 4-Channel RCA Interconnects

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio MUD100.4 4-Channel Power Sports Amplifier.
MTX Audio THUNDER1000.1

2000W Peak (1000W RMS) Thunder Series Class-D 1-Ohm Stable Monoblock Amplifier

THUNDER1000.1 main
Go to item page

2000W Peak (1000W RMS) Thunder Series Class-D 1-Ohm Stable Monoblock Amplifier

• RMS: 350W x 1 @ 4 ohms, 600W x 1 @ 2 ohms, 1000W x 1 @ 1 ohm
• Total Peak Power: 2000W
• 3-Way Protection Circuitry
• Selectable Bass Boost (0-6-12 dB)
• Class D Circuitry
• Dimensions: 6-5/16"W x 12-1/8"L x 2-1/4"H

2
MTX Audio THUNDER1000.1

2000W Peak (1000W RMS) Thunder Series Class-D 1-Ohm Stable Monoblock Amplifier

In stock

Only 2 Left!

$399.95 (12.50% off)
$349.95
Hide info
More info Item page
5 Special offers
  • FREE Premium True 0 Gauge Wiring Kit with Select Amps
  • Get 25% Off DD-1 Distortion Detector!
  • Get 20% off MTX Audio Bass Remote with Purchase!
  • 25% off an NVX True 1/0 Gauge Amp Kit with Select Amplifier!
  • 50% Off XCAP1F 1.0 Farad Capacitor with Amplifier Purchase

Item Added to Cart

THUNDER1000.1 small

2000W Peak (1000W RMS) Thunder Series Class-D 1-Ohm Stable Monoblock Amplifier

$349.95

Keep Shopping

NVX XKIT02 True 0-Gauge Wiring Kit

In case you didn't know, NVX has top notch wire for your new amp! Don't forget the RCA's!

$129.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$19.95

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio THUNDER1000.1.
MTX Audio WET75.2 2-Channel Marine Amplifier

400W Peak (200W RMS) Wet Series Class AB Bridgeable 2-Channel Marine Amplifier

WET75.2 main
Go to item page

400W Peak (200W RMS) Wet Series Class AB Bridgeable 2-Channel Marine Amplifier

• RMS Power: 75W x 2 @ 4 ohms, 100W x 2 @ 2 ohms, Bridged, 200 watts x 1 chan
• Total Peak Power: 400W
• Weather Resistant in Accordance with IP55 Rating
• Dimensions: 7.90"W x 6.40"L x 2.25"H

MTX Audio WET75.2 2-Channel Marine Amplifier

400W Peak (200W RMS) Wet Series Class AB Bridgeable 2-Channel Marine Amplifier

In stock

Only 1 Left!

$249.95 (8.00% off)
$229.95
Hide info
More info Item page
2 Special offers
  • Save 50% on an 8 Gauge Amp Kit with Purchase!
  • 50% Off NVX Universal Bluetooth Controller with Purchase!

Item Added to Cart

WET75.2 small

400W Peak (200W RMS) Wet Series Class AB Bridgeable 2-Channel Marine Amplifier

$229.95

Keep Shopping

Belva 1.0 Farad Capacitor + Amp Kit

BB1D 1.0 Farad Capacitor + BAK42BK Complete 4 Gauge Amplifier Wiring Kit

$54.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio WET75.2 2-Channel Marine Amplifier.
MTX Audio WET500.1

500W Wet Series Mono Block Class D All-Weather Powersports/Marine Amplifier

WET500.1 main
Go to item page

500W Wet Series Mono Block Class D All-Weather Powersports/Marine Amplifier

• RMS Power: 300W x 1 @ 4 ohms, 500W x 1 @ 2 ohms
• Total Peak Power: 500W
• Plastic Cover Over Control-Adjustments
• Dimensions: 8.90"W x 6.40"L x 2.25"H

MTX Audio WET500.1

500W Wet Series Mono Block Class D All-Weather Powersports/Marine Amplifier

Special order

Ships at Later Date

$279.95 (10.72% off)
$249.95
Hide info
More info Item page
2 Special offers
  • 50% Off NVX Universal Bluetooth Controller with Purchase!
  • Get 20% off MTX Audio Bass Remote with Purchase!

Item Added to Cart

WET500.1 small

500W Wet Series Mono Block Class D All-Weather Powersports/Marine Amplifier

$249.95

Keep Shopping

Belva BAK42BK 4 Gauge Amplifier Installation Kit

Great amps need great wire at a great price. This amp kit has everything you need!

$29.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Bass Remote

A bass remote made specifically for the this amplifier.

$19.95

Add

Don't see the accessory you're looking for?
View all available accessories for the MTX Audio WET500.1.

Related Categories


MTX Marine Amplifiers MTX Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

MTX Motorcycle Amplifiers MTX Motorcycle Amplifiers

Your motorcycle will sound better than ever with the proper amplifier. Most of these amps are specially designed with special materials that can withstand the vibrations and elemental exposure, while others are designed with an extremely small footprint to fit conveniently in a saddlebag or other tight installations. Many of the products in this category are specifically designed for certain motorcycles, making installation a breeze.

MTX Mini Amps Information

Amplify your audio with MTX min amps. These small but powerful amps can fit in tight spaces and provide enough power for your car audio system. MTX has the knowledge and experience when it comes to mini amps.
    clear all items