Power Acoustik Add an Amplifier to Your Factory Stereo at Sonic Electronix

Power Acoustik Add an Amplifier to Your Factory Stereo

Filters
Why Shop With Us?
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

This designates the series of the amplifier. Many amps are available in a litany of different wattage and channel configurations, but maintain consistent features throughout the product line.
The lowest impedance the amplifier will handle when it is not bridged.
The lowest impedance the amplifier will handle when it is bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
Power Acoustik OD4-1300 + NVX XFLOC4 Line-Output-Converter + Amp Kit

1,300 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp Kit

OD4-1300, XFLOC4, BAK44 main
Go to item page

1,300 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp Kit

• Class-A/B Full Range 4-Ohm Stable 4-Channel Amplifier
• 100 Watts RMS x 4 @ 4 ohms
• 160 Watts RMS x 4 @ 2 ohms
• Bridged, 320 Watts RMS x 2 @ 4 ohms
• Total Peak Power: 1300 Watts
• Military Grade PCB w/ PWM MOSFET Power Supply
• High/Speaker Level & Low Level/RCA Input

71
Power Acoustik OD4-1300 + NVX XFLOC4 Line-Output-Converter + Amp Kit

1,300 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp Kit

In stock

$224.97 (30.22% off)
$156.99

Item Added to Cart

OD4-1300, XFLOC4, BAK44 small

1,300 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp Kit

$156.99

Keep Shopping

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$19.99

Add
NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

$99.99

Add
NVX XTGSP2

Perfect for safely troubleshooting and testing audio systems

$29.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Power Acoustik OD4-1300 + NVX XFLOC4 Line-Output-Converter + Amp Kit.
Power Acoustik OD4-1800 + NVX XFLOC4 Line-Output-Converter + Amp kit

1,800 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp kit

OD4-1800, XFLOC4, BAK44 main
Go to item page

1,800 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp kit

• Class-A/B Full Range 4-Ohm Stable 4-Channel Amplifier
• 140 Watts RMS x 4 @ 4 ohms
• 225 Watts RMS x 4 @ 2 ohms
• Bridged, 450 Watts RMS x 2 @ 4 ohms
• Total Peak Power: 1800 Watts
• Military Grade PCB w/ PWM MOSFET Power Supply
• High/Speaker Level & Low Level/RCA Input

71
Power Acoustik OD4-1800 + NVX XFLOC4 Line-Output-Converter + Amp kit

1,800 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp kit

In stock

$227.97 (29.82% off)
$159.99

Item Added to Cart

OD4-1800, XFLOC4, BAK44 small

1,800 Watt Max 4-Channel Amplifier + NVX 4-Channel L.O.C. + 4 Gauge Amp kit

$159.99

Keep Shopping

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$19.99

Add
NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

$99.99

Add
NVX XTGSP2

Perfect for safely troubleshooting and testing audio systems

$29.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Power Acoustik OD4-1800 + NVX XFLOC4 Line-Output-Converter + Amp kit.
Power Acoustik OD2-1000 + NVX Line-Output-Converter + Amp Kit

1,000 Watt Max 2-Channel Full Range Amplifier + NVX 2-Channel L.O.C + 4 Gauge Amp kit

OD2-1000, XLCA2, BAK42 main
Go to item page

1,000 Watt Max 2-Channel Full Range Amplifier + NVX 2-Channel L.O.C + 4 Gauge Amp kit

• Class-A/B Full Range 4-Ohm Stable 2-Channel Amplifier
• 120 Watts RMS x 2 @ 4 ohms
• 200 Watts RMS x 2 @ 2 ohms
• Bridged, 400 Watts RMS x 1 @ 4 ohms
• Total Peak Power: 1000 Watts
• Military Grade PCB w/ PWM MOSFET Power Supply
• High/Speaker Level & Low Level/RCA Input

153
Power Acoustik OD2-1000 + NVX Line-Output-Converter + Amp Kit

1,000 Watt Max 2-Channel Full Range Amplifier + NVX 2-Channel L.O.C + 4 Gauge Amp kit

OUT OF STOCK

$241.97 (23.55% off)
$184.98

Item Added to Cart

OD2-1000, XLCA2, BAK42 small

1,000 Watt Max 2-Channel Full Range Amplifier + NVX 2-Channel L.O.C + 4 Gauge Amp kit

$184.98

Keep Shopping

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

$19.99

Add
NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

$99.99

Add
NVX XTGSP2

Perfect for safely troubleshooting and testing audio systems

$29.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Power Acoustik OD2-1000 + NVX Line-Output-Converter + Amp Kit.
    clear all items