Memphis 5-Channel or more Amps at Sonic Electronix

Memphis 5-Channel or more Amps

Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
listview icon
gridview icon
Memphis PRXA700.5

700 Watt 5-Channel Power Reference Amplifiers

PRXA700.5 main
Go to item page

700 Watt 5-Channel Power Reference Amplifiers

• RMS Power: 50 watts x 4 chan.+ 200 watts x 1 chan.@ 4 ohms, 75 watts x 4 chan.+ 400 watts x 1 chan. @ 2 ohms
• Total Peak Power: 500W
• CEA-2006 Compliant/Preamp Outputs/LPF
• 7.5"W x 16.1"L x 2.1"H

Memphis PRXA700.5

700 Watt 5-Channel Power Reference Amplifiers

OUT OF STOCK

 
$529.95

Item Added to Cart

PRXA700.5 small

700 Watt 5-Channel Power Reference Amplifiers

$529.95

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XIV65 V-Series Interconnect Cable

5m (16.40 ft) 6-Channel RCA Audio Interconnect Cable

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Memphis PRXA700.5.
Memphis MXA850.5M

850 Watts 5-Channel Xtreme Audio Amplifiers

MXA850.5M main
Go to item page

850 Watts 5-Channel Xtreme Audio Amplifiers

• RMS Power: 4 ohms: 60 watts x 4 chan. / 175 watts x 1 chan.,2 ohms: 100 watts x 4 chan. / 300 watts x 1 chan., 450W x 1 @ 1 ohm
• Total Peak Power: 850W
• CEA-2006 Compliant/Preamp Outputs/LPF
• DIMENSIONS: 6.10"W x 13.4"L x 2.16"H

Memphis MXA850.5M

850 Watts 5-Channel Xtreme Audio Amplifiers

OUT OF STOCK

 
$539.95

Item Added to Cart

MXA850.5M small

850 Watts 5-Channel Xtreme Audio Amplifiers

$539.95

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX XIV65 V-Series Interconnect Cable

5m (16.40 ft) 6-Channel RCA Audio Interconnect Cable

$34.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Memphis MXA850.5M.
Memphis VIV750.6V2

750 Watt 6-Channel VIV SixFive Series Amplifiers

VIV750.6V2 main
Go to item page

750 Watt 6-Channel VIV SixFive Series Amplifiers

• RMS Power: 70W x 6 @ 4 ohms, 125W x 6 @ 2ohm
• Total Peak Power: 750W
• CEA-2006 Compliant/Preamp Outputs/LPF
• DIMENSIONS: 8.2"W x 9.3"L x 2.2"H

Memphis VIV750.6V2

750 Watt 6-Channel VIV SixFive Series Amplifiers

OUT OF STOCK

 
$699.95

Item Added to Cart

VIV750.6V2 small

750 Watt 6-Channel VIV SixFive Series Amplifiers

$699.95

Keep Shopping

Belva BAK46 6-Channel 4 Gauge Amplifier Installation Kit

Complete 6-Channel CCA 4 Gauge Amp Kit with RCA Cables and Speaker Wire

$59.99

Add
FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
Stinger SI4612 4000 Series Interconnect Cable

12 ft. 6-Channel 4000 Series Audio Interconnect Cable

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Memphis VIV750.6V2.

Related Categories


Memphis Amplifier Wiring Kits Memphis Amplifier Wiring Kits

Get all the cables, wires, and hardware you need to install your new car audio amplifier with one of these power amp kits.

Memphis EQs, Signal & Sound Processors Memphis EQs, Signal & Sound Processors

Find a quality line output converter, digital sound processor, EQ, crossover or bass enhancer in here.

Memphis Marine Amplifiers Memphis Marine Amplifiers

Enhance the sound on your boat by adding an amplifier to your marine audio system. These marine amps are the perfect way to get louder, bigger, and clearer sound quality on your boat. These marine amplifiers can be great for standard boat speakers, tower speakers, and even some marine PA systems. Each amp is specially treated and engineered to function in the same wet, salty environment that boats are in.

    clear all items