Focal Mini Amps at Sonic Electronix

Focal Mini Amps

Their small form factor and ease of installation makes Focal mini amps a popular product.
Filters
Loading...
Filters

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

The lowest impedance the amplifier will handle when it is not bridged.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Sonic Certified amplifiers have been tested by the experts at Sonic Electronix to meet or exceed the wattage ratings provided by the manufacturer. If this is marked as Yes, then you can trust the wattage ratings. If marked as No, then we have tested the amplifier and it did not meet the advertised wattage ratings. If marked as Not Tested, then the Sonic Electronix experts have not yet been able to test the amp.
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

This feature will tell you if the amplifier has the capability to connect to a Bluetooth device.
listview icon
gridview icon
Focal IMPULSE4.320

Plug & Play Line Compact 4-Channel Digital Amplifier

IMPULSE4.320 main
Go to item page

Plug & Play Line Compact 4-Channel Digital Amplifier

• 55 Watts RMS x 4 @ 4 ohms
• 80 Watts RMS x 4 @ 2 ohms
• Ultra-compact – Easy to install
• CEA-2006 Compliant/Preamp Outputs/LPF
• Compatible with all head units (OEM and after-market)
• Automatic start-up with your original head unit
• Dimensions: 6-15/16"W x 1-7/8"H x 2-5/8"D

Focal IMPULSE4.320

Plug & Play Line Compact 4-Channel Digital Amplifier

In stock

Only 2 Left!

$440.00 (0.00% off)
Vip Icon $439.99
Hide info
More info Item page
1 Special offer
  • Save 50% on a 10 AWG Amplifier Power Installation Kit!

Item Added to Cart

IMPULSE4.320 small

Plug & Play Line Compact 4-Channel Digital Amplifier

$439.99

Keep Shopping

FREE NVX XMountPro Cell Phone Mount with Select Orders

Spend $200 and use code XMOUNTPRO to get this free!.

$14.99

Add
NVX Universal Remote Level Bass Control

Controls bass level and frequency via RCA/Interconnect connectors on any amp.

$9.99

Add
NVX XFLOC4

4-Channel Line Output Converter with Digital Noise Filter + Line Driver

$19.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Focal IMPULSE4.320.

Related Categories


Focal EQs, Signal & Sound Processors Focal EQs, Signal & Sound Processors

Find a quality line output converter, digital sound processor, EQ, crossover or bass enhancer in here.

Focal Motorcycle Amplifiers Focal Motorcycle Amplifiers

Your motorcycle will sound better than ever with the proper amplifier. Most of these amps are specially designed with special materials that can withstand the vibrations and elemental exposure, while others are designed with an extremely small footprint to fit conveniently in a saddlebag or other tight installations. Many of the products in this category are specifically designed for certain motorcycles, making installation a breeze.

Focal Mini Amps Information

Amplify your audio with Focal min amps. These small but powerful amps can fit in tight spaces and provide enough power for your car audio system. Focal has the knowledge and experience when it comes to mini amps.
    clear all items