• 400 Watts RMS
• 1200 Watts Max
• Composite Cone
• Santoprene surround
• Fiberglass-Reinforced ABS Basket
• IP56 Ultra Marine Certified
• Vented Pole and Basket Structure
Polk Audio MM 1042 SVC (MM1042SVC)
1200W Peak (400W RMS) 10" MM1 Series Single 4-Ohm Car Subwoofer (MM 1042SVC)
Dual 10" 3/4 MDF Sealed Subwoofer Enclosure (Belva MDFD10)
Dual 10-inch Sealed Car Sub Box Made with 3/4" MDF and lined w/ Polyfil (1.6 cu ft Airspace - 10SQB)
NVX SDBDK12 Premium Stealth Black
Premium Sound Deadening Kit, Four Door Kit w/ Four 12" x 36" Sheets (91mil THICK)
Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully and follow them till the end. It’s important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.
The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicle’s service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.
Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.
For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.
Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.
Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.
(newest, current model)
(previous model, replaced by (2) Polk Audio MM1042SVC 10” 2400w Subwoofers+Sealed Enclosure+Sound Deadening)
(previous model, replaced by Polk Audio MM1040DVC)
Overall rating distribution
By feature average rating
August 20, 2014
It's a boxf
What can I say? It's a good box, and spec for the subs I got. Good price, good build, and the sound is heavenly. For someone like me (ie, not a carpenter, not even close) this is a good choice. I'm not a fan of banana clips but they are prevalent, so there you go. It's ready to go.
April 18, 2014
Great little box
I've seen a lot of good reviews in customer service for sonic, so I took a look at there site n was blown out of the water with all the variety of high quality stuff and at a great price so I looked for a box n got this one. It's not super huge so I have some space in my trunk to utilize for groceries lol. Plenty of room for the subs hits extremely nice live that it is poly filled. Will be back to Make more purchases thanks sonic
February 8, 2014
OK wire if you like red wire
I received this wire because when I bought my Image Dynamics speakers from Sonic the description said it included speaker wire in the box, but when I received them there was none. I called Sonic and they sent this wire to make up for the error. I later called Image Dynamics and found out that they no longer include speaker wire with their speakers so Sonic if you are reading this you can update your description and pictures on the ID speakers to NOT show speaker wire. For the record I bought the Image Dynamics CTX65cs and the CTX4 speaker sets. Great speakers by the way. Thanks Sonic for all your great products and sound advice, no pun intended:)
October 18, 2007
Good box for the price!
I ordered this box a few weeks ago and I have to say for the price the box is a great buy. You will need to re-seal / re-caulk all in the seams and speaker terminals on the inside of each chamber to get a tight seal, but this is normal with most prefab boxes you buy. I have had to seal every prefab box regardless if they say it has been sealed or not due to the fact that prefabs 95% of the time are never sealed on the front baffel / base board were the subs are mounted. Seal the box nice and neat with some silicone / caulk and throw in some fiberfill and you are good to go. Great box for the price and can't beat it.
October 19, 2013
A different usage ----
I was looking for a small enclosure to use for a bass guitar speaker cabinet. I installed (2) Eminence Delta 10 inch speakers, and installed plastic stacking corners. I also removed the plastic jack plate and replaced it with a rear port tube. The cabinet sounds GREAT ! The cabinet is constructed well, but the packaging leaves a bit to be desired. The cabinet arrived with damage to 2 of the corners, but the damage was covered by the plastic corners I installed. A slight variation from its intended usage, but the outcome was good !
Best selling similar products
• Bracket/Flush Mount Rearview Backup Camera
• Waterproof IP67 Compact Design
• Resolution: 720 x 480
• Adjustable 170 degree Viewing Angle
• RMS: 300W x 1 @ 4 ohms, 500W x 1 @ 2 ohms
• Total Peak Power: 1000W
• CEA-2006 Compliant Amplifier
• 4-Channel Speaker-Level Inputs
• Heavy Duty Aluminum Alloy Heat-Sink
• Dimensions: 7-7/8"W x 7-7/8"L x 2-3/16"H
• 340W Max Each, 60W RMS Each
• 1" Polypropylene Balanced Dome Tweeter
• Graphite-Injected Reinforced Polypropylene Cone
• 4 ohms Impedance
• Mounting Depth: 2.24"
• Peak Power: 270W Each
• RMS Power: 90W Each
• 2-Way Coaxial
• 4 ohms Impedance
• Polypropylene Cone Material
• Nitrile Butadiene Rubber Surround
• 20mm Silk Dome Tweeter
• Solid Black for Any Stealth Car Audio Installation
• 2.3mm (91mil) thick for better performance
• Quiets Vibrations
• Stops Annoying Rattles
• Increases SPL (LOUDER)
• Reduces Heat
• Simple To Install
• Peel and Stick Installation
• Two 10" x 10" Pieces
(2) MM1042 SVC,SDBDK12,BBSW167,MDFD10
Internal Product ID:
Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.