•400 Watts Max, 200 Watts RMS
• Pressed-pulp cone with cotton fibers cone material
• Neodymium Magnet
• 4 Ohms Impedance
• Sensitivity: 93 dB
• Mounting Depth: 3 "
ML 1800.3 Legend car audio woofers has been thought and designed for the enthusiasts attending contests who need a component merging the timbre accuracy of ML 1650.3 Legend to a wider extension to the low frequencies thanks to the large emission surface, higher power handling and control which only a 50 mm voice coil can ensure.
Priced Per Pair
NVX SDSK2 - 90mil 2.3mm THICK
Speaker Kit - 1.38 Square Feet of Sound Damping (Sound Deadening) Material (Two 10" x 10" Pieces)
Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully and follow them till the end. It’s important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.
The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicle’s service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.
Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.
For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.
Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.
Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.
NVX SDRLR1 Sound Dampening Rubber Roller
Universal, Professional Heavy Duty Roller for Sound Damping (Sound Deadening)
Overall rating distribution
By feature average rating
September 20, 2014
Nice Wiring Kit
This is a nice quality kit at a fair price. It had everything that was needed to complete the task.
I had purchased another kit that I really wasn't happy with, and decided to purchase this one. I liked the attention to detail in the preparation of this kit. Recommended.
January 3, 2015
Bought from Sonic along with Maxxlink VSD-TK 5 pc set. Basic shipping was fast. The roller worked very well. I have large hands and was able to use the roller without a problem. Only thing- check the tightness of the Nyloc nut and bolt that holds the roller on the handle. Mine popped apart while I was on the 5th and last section of damping material. A simple twist together plus an extra 1/8" turn and it did not come off again. I would buy again.
July 23, 2014
Why pay more?
This roller is more than capable of getting the job done. One trick you can do for tight curves is to use the handle of the roller to get the dampening material to conform to them.
All in all, a roller is roller. So, why pay more than this?
October 3, 2012
a must have when installing sound dampening products
Very nice and works very well. I would have never did as good as i did installing nvx sound dampening without this. This and the material is all you need it makes the job very simple. I would reccomend this to anyone who wants a good durable roller.
January 19, 2014
Nvx = quality at the best price.
I'm so happy with all my NVX products. They are always the best in quality and price. No smell and if it's not a lot you can apply it without a roller. (I used my hands and the back of a screw driver to really smooth it out)
March 18, 2013
NVX Sound Dampening Roller
Amazing roller gets the job done well. Seems like everytime i got into little spaces that i couldnt use the roller I cut my hands up this roller saves your hands and saves time. I did have the nut that holds the roller on come off while using it but its easy to put back on, I put it back on by hand. Worth the money for sure.
June 20, 2013
Easy to use, good performance!
We used this in conjunction with a component speaker upgrade to a 2003 VW Passat. This material is simple to use (if you can work scissors and peel off adhesive backing, you can handle this stuff!), and you can easily cut it to any size or shape to fit your particular vehicle. Installing this material was the easiest part of our whole car audio upgrade project!
Best selling similar products
6-1/2" M Series Mid-Range Driver • 280W Max • 140W RMS • 8 ohms Impedance • Reinforced Paper Cone • Foam Edge Surround • 27oz. Ferrite Magnet
• Peak Power: 300W
• RMS Power: 100W
• 1-1/4" Copper Clad Aluminum Coil Winding
• Mounting Depth: 2-7/8"
• Pulp Paper Woofer Cone
• 4 Ohms Impedance
• Stamped Steel Basket
8" Punch Series Speaker • Mid-Range Driver • 250W Max • 125W RMS • 4 ohms Impedance • High Strength Paper Cone • Treated Cloth Surround • Oversize Magnet Structure
• 200 Watts Max Each, 100 Watts RMS Each
• Pro Midrange Driver
• 4 ohms Impedance
• Sensitivity: 93.2dB
• Mounting Depth: 2.93"
• Peak Power: 300W
• RMS Power: 150W
• Mid-Bass Driver
• 8 ohms Impedance
• Treated Paper Cone
• Treated Paper Surround
ML1800.3, SDSK2, SDRLR1
Internal Product ID: