150W RMS 6.5" Coaxial Car Speakers 6.5" Speaker Baffles + Sound Dampening, Roller and Panel Removal Kit
• 400 watts Peak Each, 75 watts RMS Each
• 1" Titanium Dome Tweeters
• Curvilinear mica fiber composite cone material
• Impedance: 4 ohms
• Sensitivity: 94 dB
Priced Per Pair
NVX SDBSK2 Premium Stealth Black
Premium Sound Damping (Sound Deadening) Speaker Kit, two 10" x 10" Sheets (91mil THICK)
Quantity: 1
Five Piece Installer Panel Removal Tool Kit for Car Stereo/Audio (Belva BTK105)
Five Piece Installer's Panel Removal Installation Tool Kit for Car Stereo, Speakers and Car Audio Installs
Quantity: 1
Stop wrapping screwdrivers in electrical tape and hoping for the best. If you want to make your next installation smooth, and keep your interior immaculate, pick up a set of these Belva BTK105 Panel Removal Tools.
This set of nylon plastic tools make your job easier when it comes to pulling off those interior pieces, but it also keeps you from marring your finish. When you're done with the job, no one will know you ever pulled anything off in the first place. Make your next audio improvement a cinch with the Belva BTK105 Panel Removal Tools.
Internal Product ID:
199037
No speaker grills nor wire
I don't understand why they do not include any grills or wire. Can you buy grills from other models to use with these? On the plus side ... These speakers are 94db 1watt at 1 meter. Every 3db is twice as loud. So these are currently the only 6.5" speakers that are 4 ohms and are so sensitive to low wattage. For those of you experimenting with t-amp's and tpa3118 and tpa3116 small digital amps this speaker should be a dream come true, mostly because it is twice as loud as a 91db speaker at the exact same wattage.
97
found this helpful.Apparently, one size does not fit all 6.5" speakers...
Unfortunately, I cannot give a review on the product's performance as I was unable to use it in the manner for which it was manufactured due to incompatible size issues. The speakers I have are the CVMPCL6.5 - 6.5" STROKER PRO 200W Midrange Gold Speakers. Pairing these speakers with the NVX XBAF65 Speaker Baffle Ring Kit spawned two issues:
1) The mounting depth for the baffles is 2-5/8" (2.625 inches), whereas the mounting depth for the speakers is 2.930 inches. This minor difference was seemingly insignificant until the second issue reared its ugly head.
2) The width of the baffles is much too small for my speakers. I can't seem to find information on the exact dimensions of the baffles as I have not yet contacted NVX. But the width (diameter) of my speakers is < 5.76 inches. This is obviously too wide for the baffle because the baffle would not go on without a fight. I pulled, tugged, stretched, and strained nearly damaging the speaker. I then decided to make a few modification cuts to the baffle to accommodate the sheer width of the speaker, but the result was a shredded baffle and a traumatized speaker.
Now I'm stuck with three unusable baffles because I bought two pair!
Regarding speaker width, the CVMPCL6.5 - 6.5" STROKER PRO 200W Midrange Gold Speakers have unremovable hardware tabs attached to them that I can only assume are there to somehow protect the speaker leads. They stick out from the speaker basket making it impossible to properly install the baffle and, in turn, causing the magnet to protrude out of the base of the baffle a lot farther than it would have if the baffle were wide enough.
Regarding the attached photos, the unmodified baffle from the first pair was used to demonstrate the issue.
Attachment: Photos
**** VENDOR RESPONSE ****
The XBAF65 are made for nearly all 6.5" speakers. The Cerwin-Vega pro midrange seem to be the culprit as their depth and basket are atypical.
We will do our best to come out with a new, larger "oversized 6.5" version and name it XBAF675. It will take us some time to tool and come out with it, but hope you enjoy the feedback.
82
found this helpful.Foam vs Rubber
The best thing about these speaker baffles are the fact that they are rubber vs the easy to find foam. They definitely add a nice level of water resistance with the rubber. Not to mention the sound quality improvement. It's seriously a night and day difference. Trust me, just buy them!
80
found this helpful.Protect Your Purchase
I like these baffle rings because it gives that added protection for my mid-bass component from any water that may slip through the window sill. It also helps with reducing any unwanted vibration noise. The egg crate foam placed behind the speaker on the inner lining of the door helps absorb waves to add more decrease in vibration.
The silicone-rubber material is going to last a long time and can be easily trimmed for a custom fit.
68
found this helpful.But them a must have
I makes sound project forward and also gives piece of mind of some possible water resistance........ A must have for better sound quality
68
found this helpful.absolutely perfect!
highly recommend for a clean speaker install. helps keep from losing mid-range sound.
65
found this helpful.Helps doors
Great baffles to help the high powered door speakers bang
62
found this helpful.Five Piece Installer Panel Removal Tool Kit for Car Stereo/Audio (Belva BTK105)
Good for the price, could be better, does what it’s supposed to
62
found this helpful.The best speaker baffles!
Love these baffles! The rubber makes it easy to mount, you could trim them but it wasn't necessary in my case. Love the little foam circle that goes with it! Improves your sound quality for sure! After I installed these baffles, all of the sounds are being directed back into the cab, its definitely louder now and adds a little more midbass.
62
found this helpful.Work good, good product
they work well. just make sure your on the spot before you stick the foam on because it is sticky.
62
found this helpful.Best selling similar products