MB Quart OA800.4 Amplifier Installation Kit for Factory 2006-13 GM Systems

800W RMS 4-Channel Onyx Series Class SQ Full-Range Amplifier Installation Package for 2006-13 GM Vehicles w/ Factory Stereo

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Compatibility List:

  • Buick
    • 2008-2011 Enclave
    • 2006-2011 Lucerne
  • Cadillac:
    • 2006-2011 DTS
    • 2012-2013 Escalade
    • 2007-2009 SRX
  • Chevrolet
    • 2007-2013 Avalanche
    • 2007-2008 Equinox
    • 2006-2013 Impala
    • 2006-2007 Monte Carlo
    • 2007-2013 Silverado
    • 2007-2013 Suburban
    • 2007-2013 Tahoe
    • 2009-2012 Traverse
  • GMC
    • 2007-2012 Acadia
    • 2003 Savana
    • 2007-2013 Sierra
    • 2007-2013 Yukon
  • Hummer
    • 2008-2009 H2
  • Pontiac
    • 2007-2009 Torrent
  • Saturn
    • 2007-2009 Outlook
    • 2008-2009 Vue
  • Suzuki
    • 2007 XL-7

MB Quart OA800.4 - Exclusive Sonic Electronix Amplifier!

800W RMS 4-Channel Onyx Series Class SQ Full-Range Bridgeable Power Amplifier
Quantity: 1

General Features:

  • Onyx Series 4-Channel Class SQ Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 100 watts x 4 chan.
    • 2 ohms: 200 watts x 4 chan.
    • Bridged, 4 ohms: 400 watts x 2 chan.
  • FLUID-FETS MOSFET Circuit maximizes power efficiency while improving sound quality
  • Heavy duty aluminum alloy heat-sink with illuminated MB Quart logo
  • LED power (green) and protect (red) indicators
  • Unbalanced RCA jack inputs
  • Built-in system diagnostics
  • 2-Ohm Stable operation, bridgeable to 4-ohms
  • 16 AWG speaker output connections
  • Full-range Preamp RCA outputs to daisy chain multiple amps
    Full-range only if a full range signal is connected to input
  • 3-way protection circuitry (thermal, overload, and speaker short protection)
  • Selectable input modes: 4ch / 2ch , allows for one set of inputs to be used
  • Input sensitivity: 200mV - 6V
  • Selectable crossover modes: LP / HP / FULL
  • Variable high-pass filter: 10 - 1,200 Hz
  • Variable low-pass filter (Ch 3 & 4 only): 30 - 150 Hz
  • Variable Bass Boost (Bass EQ, Ch 3 & 4 only): 0 - +9 dB at 45Hz
  • Frequency response: 10 - 45,000 Hz
  • Damping factor: >180
  • Signal-to-noise Ratio: >92dB
  • Total harmonic distortion: 0.05%
  • Channel separation: >80dB
  • Recommended Fuse Rating: 40A x 2
  • Dimensions: 14.17"L x 9.45"W x 2.23"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty


Check out the MB Quart OA800.4 Owner's Manual

Belva BAK44

Complete 4 Gauge Amplifier Wiring Kit with 4-Channel RCA Interconnects (CCA Wiring)
Quantity: 1

General Features:

  • Complete 4 Gauge 4-Channel Amplifier Installation Kit
  • Designed specifically for car audio systems up to 1000 watts RMS
  • Premium Powerflex power and ground wire provides optimal power transfer
  • Made from Copper-Clad Aluminum for a pure uninterrupted transfer of power and signal
    • Belva CCA wire is made from 30% copper while other CCA wire is just 10% copper
  • Helical Twist Construction Audio Interconnect RCA cables minimize noise and interference
  • In-line Mini-ANL Fuse holder with a 80 amp Mini-ANL fuse offers ideal protection for high powered systems
  • Also available as 2-Channel Kit
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Kit includes:

  1. 17 ft. (5.2 meters) Red 4 gauge power wire
  2. 3 ft. (.91 meters) Black 4 gauge ground wire
  3. 17 ft. (5.2 meters) Gray 18 gauge remote lead wire
  4. 17 ft. (5.2 meters) Helical Twist 4-channel RCA interconnect cable
  5. 65 ft. of Speaker Wire
  6. One In-line Mini-ANL Fuse Holder with a 80 amp Mini-ANL fuse
  7. One Black rubber firewall grommet
  8. One 4 Gauge red chrome plated ring terminals
  9. One 4 Gauge black chrome plated ring terminal
  10. Three 18 Gauge red Spade terminal
  11. Two 18 Gauge black Spade terminal
  12. One 18 Gauge red butt connector
  13. Ten 4" Black zip ties

PAC Amplifier Integration Interface for Select GM Vehicles (AOEM-GM1416)

Interface Module that Allows the Addition of an Amplifier in Select 2006 - 2013 General Motors Vehicles [Chevrolet, GMC, Cadillac, etc...]
Quantity: 1

Product Features:

  • Interface that Allows the Replacement or Addition of an Amplifier in Select GM Vehicles
  • Interface is transformer isolated
  • Maintains phase
  • Linear from 20-20,000 Hz
  • Provides 2:1 gain and infinite attenuation
  • Input connectors plug into factory stereo and vehicle harness
  • Not compatible with premium factory amplified systems
  • Not compatible with Navigation equipped vehicles
  • Warning chimes will sound through the front left RCA output
  • Four female RCA output jacks connect to amplifier
  • 1-year Manufacturer's warranty

This AOEM Kit Includes the following:

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

100 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

200 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

400 watts x 2 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

SQ
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

1600 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

800 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.05%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-Pass (LP)
High-Pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

10 - 1200 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

30 - 150 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
>92 dB
Channel Separation
Also referred to as crosstalk. The amount of interference on one stereo channel caused by the leaking of the other stereo channel. The higher the rating in decibels (dB), the better the Channel Separation.
>80 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 9 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
40A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Amplifier Kit Specifications

Number of Amplifiers Supported
This is the number of amplifiers that the amplifier kit can support. If you are are going to be powering more than one amplifier, make sure that the installation kit will support them.
1
Power/Ground Wire Size
The power/ground gauge numbers represents the main wire size of the amplifier kit.

Definitions are as follows:

Gauge (wire) - The diameter of a wire. The higher the number, the thinner the wire. Example: 4 gauge wire has more strands than 10 gauge wire.

AWG (American Wire Gauge) - A standard of the dimensional characteristics of wire used to conduct electrical current or signals. AWG is identical to the Brown and Sharpe (B & S) wire gauge.
4 gauge
Power Wire Length
This is the length of the power wire in feet.
17 feet
Ground Wire Length
The length of the ground wire in feet.
3 feet
Speaker Wire Included
If speaker wire is included, the value will be "Yes" and if no wire is included, it will read "No".
Yes
Speaker Wire Length
This is the length of speaker wire that is included with the item.
65 feet
Remote Wire Length
This is the length of the remote wire that is included with the item.
17 feet
Interconnect (RCA) Signal Cables Included
Interconnect cables are required for amplifiers which are installed to the "RCA preamp low-level outputs" of a car stereo receiver. If your amplifier has high-level / speaker level inputs, then you do not need to purchase interconnects; however, interconnects offer a much higher quality sound when compared to speaker level inputs.
4 Channel
Fuse Holder
This is the type of fuse holder that is included in the item.
Mini ANL
Fuse Size
This is the size of the fuse that is compatible with the fuse holder. If the fuse needs to be replaced, be sure to replace it with the same size.
80A
Distribution Block Included
This means that the kit includes a distribution block in the package. This will assist in the installation of the amplifier kit or any situation where a distribution block is required.
No

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

NVX XBG3PK Big 3 Kit with True 0 Gauge 100% Oxygen-Free Copper

1/0 AWG Big 3 Upgrade Kit with 100% OFC Wire for Audio Sytems up to 350 Amps

Your Price $69.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

OA800.4_AOEM-GM1416_BAK44

Weight

15.58lbs

Internal SKU

oa8004_aoemgm1416_bak44

Internal Product ID

129097

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: MB Quart OA800.4 Amplifier Installation Kit for Factory 2006-13 GM Systems

Item Added to Cart

MB Quart OA800.4 Amplifier Installation Kit for Factory 2006-13 GM Systems

800W RMS 4-Channel Onyx Series Class SQ Full-Range Amplifier Installation Package for 2006-13 GM Vehicles w/ Factory Stereo

$156.27

Keep Shopping

Get Added Peace of Mind with SquareTrade

Why SquareTrade?

  • The #1-Rated Protection Plan
  • 5-Day Service Guarantee & Free Shipping
  • Protection from Normal, Everyday Use
You have added a warranty
$19.99
Add Warranty
3 years of protection

NVX XBG3PK Big 3 Kit with True 0 Gauge 100% Oxygen-Free Copper

1/0 AWG Big 3 Upgrade Kit with 100% OFC Wire for Audio Sytems up to 350 Amps

$69.99

Add

Don't see the accessory you're looking for?
View all available accessories for the MB Quart OA800.4 Amplifier Installation Kit for Factory 2006-13 GM Systems.