Slim 600 Watt 10" Amplified Powered Subwoofer Enclosure
Bundles with this Product
10% Off a Sound Dampening Kit with Your Subwoofer Purchase!
Save 10% when you add an NVX SDTK20 Sound Dampening Trunk Kit to your Subwoofer purchase. Simply click the "Add Both to Cart" button. This offer cannot be combined with any other coupons or offers.
NVX SDTK20 - 90mil 2.3mm THICK
Special Price $53.99 ($59.99 if purchased separately)
NVX SDTK20 - 90mil 2.3mm THICK
• Eliminates Road Noise
• 2.3mm (90.55mil) thick for better performance
• Quiets Vibrations
• Stops Rattles Increases SPL
• Reduces Heat
• Simple To Install
• Easy To Form Aluminum
• Four Step Peel and Stick Installation
• Five 18" x 32" Pieces
(Offer 1 of 1)
Combined Total Price
You Save $6.00
This shallow-mount loaded subwoofer box is the perfect addition for any truck or a hatchback vehicle looking to save some additional space. The 600 Watts of Peak power gives you more than enough power to produce that low end bass you were looking for. This box was specifically designed for someone who wants an upgrade over their factory bass system and doesn't want to sacrifice the amount of space that the average sub box will use up.
This enclosure is already perfectly matched with its corresponding amplifier so there is no need to go through the struggle of finding an amplifier that will actually work with this subwoofer. It provides the proper amount of power to get the most out of this 10-inch subwoofer.
- Shallow-mount 10-inch Amplified Loaded 600W Max Subwoofer Box
- Power Handling:
- Peak: 600W
- RMS: 200W
- Final Impedance: 4 ohms
- 10" Slim subwoofer box system
- Non-press paper cone
- Specially treated foam surround
- 4 Layer Dual Voice Coil
- Frequency Response: 40 Hz - 1 KHz
- Sensitivity: 90dB
- Rear Sealed Design
- Enclosure Dimensions: 19.68" W x 13" H x 5.9" D
- Authorized Internet Dealer
- 1-year Manufacturer's Warranty
Amplifier Power Specifications
Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.
It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.
The RMS power rating is more accurate, and we recommend using it for product comparison.
RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.
The RMS output figure is much more accurate than the peak rating when comparing products.
- RMS Power
- Signal-to-Noise Ratio
This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.
If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.
Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.
Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.
Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.
Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
Warranty and Return Policy
Internal Product ID
Wiring Diagram Legend
Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.