Refers to the size of the speaker measured in inches. Every vehicle has standard application sizes. Please use our vehicle fitment guide for your vehicle's specific speaker sizes if you do not know them.
The number of individual drivers in a car speaker. Speakers with 2 drivers are known as a 2-way, and 3 drivers are known as a 3-way. Component systems are often referred to as "separates" because the tweeter is not attached to the midwoofer (main speaker driver) and mounts separately in a location such as a door post. Component systems typically come with an external crossover so you can easily adjust the high and low frequencies sent to both the midwoofer and the tweeter. Center channel speakers are great for those looking to have surround sound in their vehicle.
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
Many brands group their products into series or lines of products to help customers know the level of quality (good, better, best for example). You can filter by series and the brand using our guided browsing.
An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.
Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.
Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.
Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.
RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.
The RMS output figure is much more accurate than the peak rating when comparing products.
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.
Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.
Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
•8” Slot-Ported Amplified Subwoofer Enclosure
• Built-In Class D Amplifier
• Protection bars prevent damage
• Enclosure Dimensions: 8" TD x 10-3/8" BD x 9-7/8" W x 11-1/4" H
•8” Slot-Ported Amplified Subwoofer Enclosure
• Built-In Class D Amplifier
• Protection bars prevent damage
• Enclosure Dimensions: 8" TD x 10-3/8" BD x 9-7/8" W x 11-1/4" H
We love people and we're ready to help you!
See what separates us from our competition.
Free perks, no PrimeTM fees
Take advantage of our VIP rewards like 10% back on your purchases, free 2-day shipping, extended warranties, and free returns! Gain access to all of these rewards without any membership fees.
Free install gear for stereos
Get great discounted (and possibly FREE) installation accessories with most car stereo purchases. This includes dash kits, wiring harnesses and antenna adapters that you will need to properly install your new car stereo.
Authentic & Authorized
We are an Authorized Dealer for all the brands we sell, including the most premium brands in car and marine audio such as Hertz, JL Audio, NVX, Rockford Fosgate, Kicker, Alpine, Kenwood and many more.
View best sellers, deals, and more
Shop Deals and get up to 30% off premium brands! Shop Now! We are always looking out for the best products and deals to offer our customers. Don’t pay too much by shopping elsewhere!
Learn about All Car Audio
We have information on brands, gear, and more for you to explore! Check out our YouTube Channel for helpful how-to videos, product reviews, and Q&As. For a more detailed look, also visit our Learning Center!
Call or email our experts
Our trained experts are here to assist you! They are just a phone call or click away to help you get the right gear for you and your vehicle!