Expert Service 1-877-289-7664 [Hours]

Fall Blow Out Dot Sale

Kicker DX200.4 (11DX200.4)

200W 4-Channel DX Series Class A/B Amplifier

Discontinued
|

Good news and a little bad...

This item has been discontinued

But you may be interested in the newest model that's available.

41dxa2504 thumbnail

Kicker DXA250.4 (41DXA2504)

OUR PRICE: $139.95

View item

Get FAST answers from customers ASK a Question See questions answers

Why Choose Kicker DX Amplifiers:

Kicker Always Exceeds Rated Power

Kicker Performance Audio has been around since 1980 and has been producing amazing products since then. Kicker’s drive to consistently produce products that not only are great but also push the standards of the car audio industry is very apparent in all series of their amplifiers. All Kicker amplifiers are CEA-2006 Compliant, assuring you are receiving a continuous certified RMS power rating. Kicker will always exceed the rated power because Kicker is notorious for under rating their amplifiers. So really you will be getting more power than you actually pay for, which is not true for other lower end performance amplifiers that generally over rate their amplifiers. Kicker amplifiers will provide a choice of three automatic turn-on modes; remote, DC offset, or signal sense, which make them compatible with any car audio system. Along with their high-density convection heat sink for extreme heat dissipation and high efficiency MOSFET power supply, Kickers amplifiers are great way to go when selecting the perfect amplifier for your car audio system.

Kicker FIT Fail Safe Integration Technology

Kicker Fail Safe Technology (FIT):

Kicker has manufactured a new Fail-Safe Integration (FIT) technology into all of their amplifiers. The FIT technology uses isolated differential inputs in order to reject noise or electrical interferences, caused by engines, alternators or any other audio or video component throughout your vehicle. The differential inputs will use a muting circuit that will block out any additional noise that may stream down the line. The FIT technology will help created the cleanest and purest sound possible for any audio system. The Kicker FIT technology is setting the standard for high quality sound.

  • DX Series 4-Channel Class A/B Car Amplifier
  • RMS Power Rating (14.4V):
    • 4 ohms: 25 watts x 4 chan.
    • 2 ohms: 50 watts x 4 chan.
    • Bridged, 4 ohms: 100 watts x 2 chan.
  • Max power output: 100 watts x 2 chan.
  • High efficiency MOSFET power supply
  • LED power and protect indicators
  • Selectable bass boost (0 or +9 dB at 40 Hz)
  • Mono channel operation
  • Preamp RCA outputs
  • Muting circuit cancels out unwanted noise
  • FIT (Fail-Safe Integration Technology) utilizes differential inputs to reject noise and electrical interference for the quietest operation possible and ultimate audio clarity
  • Balanced differential inputs for noise elimination and factory-radio compatibility
  • 3 Automatic turn-on modes (remote, DC offset, signal sense)
  • High-density convection heat sink for extreme heat dissipation
  • Gold-plated RCA level inputs
  • Gold-plated screw terminals
  • Input sensitivity:
    • Low level: 125mV-5V
    • High level: 250mV-10V
  • Fixed high-pass filter (100 Hz, 18 dB/octave)
  • Fixed low-pass filter (80 Hz, 18 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 20-20,000 Hz
  • Dimensions: 10-1/4"L x 8-5/16"W x 2-1/4"H
  • Actual power exceeds rated power, documented inside each carton
  • 8-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
  • Item is a part of Kicker ProFit Group
  • Authorized Internet Dealer
  • 2-year Manufacturer's warranty

Extend your Kicker warranty to 3 Years when you install your new Kicker amplifier with a compatible Kicker power kit! For a limited time, you can register your Kicker amplifier and power kit to qualify for an additional year of coverage. This offer is only available through official Kicker dealers and will only last for a limited time. With this amplifier, the following power kits will qualify for the extended warranty program: Kicker 09PK8, Kicker 05CK8, and Kicker 09ZCK8.

2011 Kicker Authorized Online Dealer and eBay Seller

Product History:

Kicker 41DXA2504 thumbnail
(newest, current model)
Kicker 11DX200.4 thumbnail
(previous model, replaced by Kicker DXA250.4 (41DXA2504))

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

25 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

50 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

100 watts x 2 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

200 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
1%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
2 pairs
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

100 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

80 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
95 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 or +9 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!
On Sale

Warranty and Return Policy

Parts Warranty Duration
2 years
Labor Warranty Duration
2 years
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
4.8
Usability
5.0
Ed

reeds spring, MO

Overall
Durability
Value
Features
Design
Usability
great amp for the $

December 2, 2013

Easy install,puts the power to the speakers great. Real easy to adjust the gain control and the other features. Very happy

0 of 0 found this helpful

Help our customers find the most helpful reviews

Codeman

Houston, Tx

Overall
Durability
Value
Features
Design
Usability
Kicker 11dx200.4

June 3, 2012

I purchased this for my pioneer speakers that are rated at 40rms a piece and this little baby pushes more than enough power to them. I would recommend this product for people that are installing between 400 and 1000 watts of bass.

0 of 0 found this helpful

Help our customers find the most helpful reviews

greg

east amherst, NY

Overall
Durability
Value
Features
Design
Usability
fast shipping amazing price

March 2, 2012

I originally ordered the 08DX200.4 and for free they upgraded me to the 11DX200.4. I ordered Monday and by Wednesday was already at my door step, i havent hooked it up yet to my DS60 speakers. When i do i will update.

0 of 0 found this helpful

Help our customers find the most helpful reviews

sKnNyPpY

Columbia, SC

Overall
Durability
Value
Features
Design
Usability
Solid little amp

January 21, 2012

This amp is a little beast. I am powering Boston 6.5 separates up front and Boston 6.5 coaxs in the back. Powered by the head unit they sounded off, flat and no punch. The coaxs only take 35 watts rms so this was one of the few amps in the proper power range. It actually rates at 265, not 200 watts so I'm closer to 33 watts per channel not 25 at 4 ohms! The Bostons are alive now, bass thumping and treble singing. I also like the fader switch so I can power all 4 channels from one set of RCAs. And the price was unbeatable at SonicElectronix.com.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Chris

Roseburg, OR

Overall
Durability
Value
Features
Design
Usability
Little Powerhouse!

April 20, 2011

Great amp, Kicker makes great products, I replaced a Jensen 500W amp with this, the sound quality is day and night. The Kicker got rid of my "Ground loop" problem, no more alternator whine, you can get a lot of power out of this little amp, it may be expensive but it is worth it. Kicker makes great products and I would get another one any time

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XKIT84 4-Channel 8-Gauge Wiring Kit

In case you didn't know, NVX has top notch wire and this kit has everything you need!

Your Price $69.99

Kicker PK8 8-Gauge Wiring Kit

Great wire for your awesome new amp! Don't forget the RCA's!

Your Price $29.95

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $59.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $151.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

Small Universal Remote Level Bass Control

The Scosche RLC is a smaller universal bass remote that connects via RCA inputs.

Your Price $11.99

StreetWires FB8

8 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

NVX XIV45 4-Channel RCA Audio Interconnect Cable

5 Meters (16.4 ft.) 4-Channel RCA Audio Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $23.99

Kicker K-Series RCA Interconnect Cable

19 ft. of 4-Channel RCA cable with dual twisted-pair conductors, hyper-flex technology, and gold plated contacts for maximum signal transfer!

Your Price $29.95

Kicker 4-Channel RCA Audio Interconnect Cable

4 Meters (13 ft.) 4-Channel K-Series RCA Audio Interconnect Cable

Your Price $19.95

NVX XWS1650 Speaker Wire

50 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $29.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

11DX200.4

UPC

713034054436

Weight

5.50lbs

Internal SKU

11dx2004

Internal Product ID

29813

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Kicker DX200.4 (11DX200.4)