Expert Service 1-877-289-7664 [Hours]

Boom. SUBTEMBER is here!

2000W RE Audio + Sound Dampening Material Bass Bundle

12" RE Audio XXX12D2 XXX Series Subwoofer + NVX Sound Dampening Material

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

RE Audio plus Sound Dampening Material Bass Bundle

This Sonic Electronix Exclusive Bundle showcases a 12" Dual 2 Ohm RE Audio XXX Series Subwoofer. This subwoofer is rated at 2000 watts RMS of continues power. The subwoofer is equipped with a Kevlar reinforced kraft pulp dual composite 2-piece cone and a rubber surround for rigidity and performance. It is also equipped with tork-tite terminals, and dual progressive spiders for increased excursion. With an VMS vented magnet system that reduces heat excursion, this RE Audio XXX series subwoofer is sure to provide efficient sound and bass for long periods of time. In order to improve the all around sound of your audio car system, this bundle also includes ten 18" x 32" pieces of Dead Shield sound dampening material. This dampening material will help reduce engine noise, vibrations, road noise and rattling to give you a higher sound quality. Four step peel and stick application makes installation simple and efficient. This sound dampening material is sure to improve the over all quality and output of your system.


 
RE Audio XXX12D2 Features:
  • 12" Dual 2 ohm XXX Series Car Subwoofer
  • Power Handling:
    • RMS: 2000 watts
  • Impedance: Dual 2 ohm
  • Kevlar reinforced kraft pulp, dual composite 2-piece cone
  • Rubber surround
  • Integrated tinsel leads
  • FEA Optimized motor structure
  • Dual progressive spiders
  • Integrated gasket
  • Tork-Tite terminals
  • 3" 4-Layer aluminum flat wire voice coil
  • Split coil design
  • VMS Vented magnet system
  • Cast aluminum basket
  • Triple stacked magnets
  • Designed specifically for sealed or ported enclosures
  • Mounting Depth: 12-3/4"
  • Mounting Hole Diameter: 11-1/2"
  • Proudly made in the USA
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
XXX 12" T/S Parameters:
  • Electrical Q Value (Qes): 0.46
  • Mechanical Q Value (Qms): 3.29
  • Total Speaker Q Value (Qts): 0.404
  • Free Air Resonance (Fs): 21 Hz
  • Equivalent Compliance (Vas): 74 liters
  • One-Way, Linear Excursion (Xmax): 54 mm
  • Efficiency (SPL 1W/1m): 83.76 dB SPL
  • Effective Piston Area (Sd): 480 cm2
  • DC Resistance (Re): 4.2 ohm
  • Nominal Impedance (Znom): Dual 2 ohm
  • Thermal Power Handling (Pe): 2000 W
  • Force Factor (Bl): 18.16

For more information on the Thiele and Small Parameters, visit our T/S Parameters Article

NVX SDBP40 Features:
  • Ten 18" x 32" Pieces of Dead Shield Sound Dampening Material
  • Eliminates road noise
  • Quiets vibrations
  • Stops rattles
  • Increases SPL
  • Reduces heat
  • Easy to form aluminum conforms to desired area of vehicle with ease
  • Four step peel and stick design for easy installation
  • Increases sound quality and output of car audio system
  • Up to 30% thicker than the leading competitors
  • 40 Square feet total
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty
  • Dimensions (each piece): 18"L x 32"W

Subwoofer Specifications

Subwoofer Series
Each subwoofer manufactured is part of a series. This is the name of the subwoofer's series.
XXX (RE Audio)
Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
2000 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
2 ohms
Voice Coil Diameter
Diameter of voice coil, usually measured in inches.
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
54 mm
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Round / Circle
Main Cone Color
This is the color of the speaker's or subwoofer's cone.
Black
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Kevlar reinforced kraft pulp, dual composite 2-piece cone
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Rubber
Magnet Structure
Defines the overall structure of the subwoofers magnet.
Subwoofer Grille
Most subwoofers are able to accommodate a universal grille; however, some subs include a grille and others have a specific, optional grille available for purchase separately. If "yes", then the subwoofer includes a grille. If "optional (sold separately)" the matching grille will need to be purchased in addition to the sub.
No
Re-Cone Kit Available
Some higher end subwoofers have replaceable cone assemblies. In case of a blown woofer, a recone kit allows for a simple replacement, as opposed to purchasing an entire new subwoofer.
No

Recommended Enclosure Specifications

Recommended Enclosure Type
This is the recommended type of enclosure that the subwoofer should be installed into. Some subwoofers are specially designed for particular enclosures.

Sealed: These enclosures completely enclose the air inside the box. These boxes produce a tight bass.

Ported/Vented: These enclosures have a slot of air to escape from the box. The result is a sound that has more "boom".

Bandpass: These are a combination of both sealed and ported enclosures. They can be very efficient, but require tuning for the best response.

Ported / Vented
Sealed
Minimum Sealed Box Volume
This value indicates the minimum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
0.85 cubic feet
Optimum Sealed Box Volume
This value indicates the ideal sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Sealed Box Volume
This value indicates the maximum sealed box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.1 cubic feet
Minimum Ported Box Volume
This value indicates the minimum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
1.7 cubic feet
Optimum Ported Box Volume
This value indicates the ideal ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
Maximum Ported Box Volume
This value indicates the maximum ported box volume that the manufacturer recommends for the subwoofer. The volume is typically displayed in cubic feet.
2.2 cubic feet
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
12-3/4"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
11-1/2"
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No

Electromechanical Parameters

Free-Air Resonance (Fs)
The free-air resonance frequency of the subwoofer, measured in Hz. At this frequency the weight of the moving parts is perfectly balanced with the subwoofers suspension system.
Equivalent Compliance (Vas)
This is the amount of air that has the same stiffness as the subwoofers suspension. The greater the rating, the lower the stiffness and larger recommended enclosure. It is measured in Liters.
Total Speaker Q Value (Qts)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including all dimensionless losses. Essentially, a high Qts value (closer to 1.0) means the subwoofer is great for sealed enclosures and a low Qts value (closer to 0) means the woofer is great in vented enclosures. A Qts of around 0.45 means the woofer will work decently in either enclosure type.
Electrical Q Value (Qes)
The subwoofers relative damping (Q) at the resonance frequency (Fs), including electrical losses. Also called the mechanical damping of the subwoofer. The unitless measurement usually varies from 0.5 10.
Electrical Resistance of Voice Coil (Re)
Amount of DC resistance of the subwoofer when measured with an ohm meter. Typically, this will read less than the impedance rating of the subwoofer.
Mechanical Q Value (Qms)
This is the subwoofers relative damping (Q) at the resonance frequency (Fs), including mechanical losses. Also called the mechanical damping of the subwoofer. This unitless measurement usually varies from 0.5 10.
Efficiency Bandwidth Product (EBP)
This number represents the trade off between having an efficient woofer and one with a wide bandwidth. To calculate this number, take the Fs and divide it by the Qes. If the number is below 50, the woofer is designed for a sealed enclosure only. If it's between 50-100 it can be used in either. Lastly, if it's greater than 100 it's designed for vented enclosures.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Accessory Tools and Products

Accessories added

Single 12" Subwoofer Angled Truck or Hatchback Box Enclosure

CARB Compliant, 5/8" MDF Shallow Sub Enclosure Lined with Polyfil.

Your Price $34.99

25 ft. of Streetwires 12 Gauge Speaker Cable

You'll need speaker wire to hook up that new subwoofer!

Your Price $44.95

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

Your Price $119.99

Dynamat Sound Dampening Bulk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $159.95

Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

Your Price $99.99

12 oz. Can of Adhesive Spray

Spray adhesive used for adhering carpet to subwoofer boxes without bubbles.

Your Price $6.99

Spring Post Terminal Cup

Makes adding a spring post terminal to an enclosure simple! Banana clip ready!

Your Price $3.99

40" x 15 Ft Piece of Premium Un-Backed Automotive Trim Carpet

Durable design for long life-span, available in many colors and shades.

Your Price $39.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $1.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Xscorpion 9-Piece Nylon Plastic Pry and Chisel Tool Set

Easily removes dash/trims, door clips, panels and pins, rubber grommets and vehicle emblems.

Your Price $14.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $79.99

4 Ft of 1/4" Thick Black Heat Shrink Tubing

Provides abrasion resistance and added protection for your cables.

Your Price $3.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $8.99

12" Protective Waffle Subwoofer Grille

Keep your subwoofer looking amazing while keeping it safe.

Your Price $4.99

Impedance Meter / Signal Generator

Easy to locate tuning frequencies of passive radiators and ported enclosures

Your Price $299.99

1 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofer

Mono Amp

Mono Amp - Option 1

2 Channel Amp - Bridged

2 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

Mono Amp

2 Channel Amp

4 Channel Amp - Bridged

3 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

Mono Amp

Mono Amp - Option 1

4 Channel Amp

4 2000W RE Audio + Sound Dampening Material Bass Bundle Subwoofers

2 Channel Amp

4 Channel Amp

Items we think you might want
XXX12D2 thumbnail
RE Audio XXX12D2

• RMS Power: 2000W
• Rubber Surround
• Dual Composite 2-Piece Cone
• Tork-Tite Terminals
• Dual Progressive Spiders
• Triple Stacked Magnets
• Flat Wire Voice Coil
• Venting System

Your Price $539.99

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

XXX12D2_SDBP40

Weight

125.00lbs

Internal SKU

xxx12d2_sdbp40

Internal Product ID

37349

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: 2000W RE Audio + Sound Dampening Material Bass Bundle