Expert Service 1-877-289-7664 [Hours]

Cerwin-Vega HEDBK112

Single 12" HED Series Bass Kit Amplified Sealed Enclosure

Discontinued
|

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Ready To Go with Cerwin-Vega's HED Amplified Loaded Enclosures

Why spend countless hours looking to match the sub with an amplifier and perfect enclosure, when the HED Series Bass Kit amplified loaded enclosures by Cerwin-Vega offer an all-in-one package deal. The HEDBK112 features a single 12" HED series subwoofer that has been pre-loaded into a specifically tuned sealed enclosure. The sealed design and custom tuning will bring out the best possible sound reproduction from the loaded subwoofer. Included in this bass kit will be a 2-channel HED series amplifier that will provide more than enough power to run the subwoofer efficiently and safely. The enclosure is made from quality 3/4" MDF wood and features single push pin terminals for easy installation and set-up. The sleek black look will accommodate any vehicle while the added remote bass know will allow for gain control from the drivers seat. If you are looking to get your feet wet in this crazy world we call car audio but don't want to spend a bundle then look no further than the Cerwin-Vega amplified sealed enclosure.

Subwoofer Features
  • 12" HED Series Single 8 Ohm Car Subwoofer
  • Impedance: Single 8 ohm
  • Composite polypropylene cone design provides the perfect weight to strength ratio & excellent durability
  • Rubber surround allows high amounts of excursion
  • Radial contact convex domes geometrical design minimizes cone flex to reduce distortion
  • Rolled aluminum former for superior thermal capabilities and increased power handling
  • Linear rolled spider provides control and dynamic sound at all volume levels
  • Nickel-Plated pushpin terminals provide low-resistance connection & corrosion resistance
  • Woven tinsel leads sewn directly into spider for greater reliability
  • Single 8 ohm high temperature aluminum voice coil
  • Cross-flow window venting reduces VC temperatures
  • Forged alloy yoke for superior magnetic field retention
  • Deep drawn heavy gauge stamped steel basket
  • 1-year Manufacturer's warranty
Amplifier Features:
  • HED Series 2-Channel Class AB Car Amplifier
  • PWM MOSFET power supply
  • LED power (green) and protect (red) indicators
  • Vega Bass Boost (0 to +12 dB bass boost at 45 Hz)
  • Soft Start Turn-on
  • Speaker-level (high-level) inputs with signal sensing for automatic turn-on
  • Preamp RCA outputs to daisy chain multiple amps
  • 3-Way System Protection circuitry
  • High-density aluminum alloy heatsink for extreme heat dissipation
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Input sensitivity:
    • Low level: 122mV-5V
    • High level: 3.8V-20V
  • Crossover selection switch
  • Variable high-pass filter (50-250 Hz, 12 dB/octave)
  • Variable low-pass filter (50-250 Hz, 12 dB/octave)
  • Damping factor: >363 at 50 Hz
  • Frequency response: 20-49,000 Hz
  • Dimensions: 11-5/8"L x 9-7/16"W x 2-1/8"H
  • 8-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website (SonicElectronix.com) when purchased together with this amplifier.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
Enclosure Features
  • Single 12" sealed loaded enclosure
  • High-quality 3/4" MDF wood construction
  • Factory tuned for optimum performance
  • Custom embroidery for enhanced cosmetics
  • Single terminal push pin cup for quick and easy installation and set-up
  • Durable black carpet
  • Dimensions: 14-9/16"L x 15-9/16"W x 14-3/8"H

Amplifier Power Specifications

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

40 watts x 2 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

75 watts x 2 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

Not Stable
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

150 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

300 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
2
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

300 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

150 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.08%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 250 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
108 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 12 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Optional (Accessory required and sold separately)
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
15A x 2 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Subwoofer Specifications

Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
12"
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Single
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
8 ohms
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
150 watts
Total RMS Power Handling
This is the total RMS power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total RMS power handling for all of the subs combined.

The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend giving your subwoofer(s) 75% - 90% of the recommended RMS rating.
150 watts
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
300 watts
Total Peak Power Handling
This is the Total Peak Power handling of all the subwoofers included in the package or enclosure.

If the loaded enclosure or amplifier and subwoofer package includes more than a single subwoofer, then this is the total peak power handling for all of the subs combined.

Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements.
300 watts
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Rubber
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Composite Polypropylene Cone (CPPC)
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
86.00 dB
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
7.50 mm
Subwoofer Design
This is the design of the subwoofer or the opening of the subwoofer enclosure. Each design has it's own benefits, whether it is a square, circle, or oval.

Round/Circle: This is the typical and common subwoofer design. They have a round cone and are a circle in design.

Square: These woofers are able to achieve a greater cone area in a smaller space. Because of the greater surface area, some square subwoofers will be louder than a round subwoofer of the same size.

Enclosure Specifications

Box Type
Represents the style of the enclosure. Be sure to purchase the appropriate enclosure type and internal volume that will be compatible with your subwoofer's recommendation.

Sealed - Sealed boxes are those that have no holes or vents in it. The only hole in a sealed box is where the subwoofer is installed. Smaller sealed boxes require more power than a larger sealed box. They provide a tight, accurate bass, while the larger sealed enclosures provide a "boomier" and louder bass.

Ported / Vented - Ported/Vented Enclosures provide an even boomier, louder bass, but less accurate then a small, sealed box. Ported enclosures typically require more airspace per sub and also less power output from an amplifier to perform correctly.

Bandpass - Bandpass enclosures make subwoofers perform efficiently, but loose. The bass is not as "boomy" as a ported enclosure nor as punchy as a sealed enclosure. Bandpass enclosures work well with lower to mid-level subwoofers.
Sealed
Number of Subs/Speakers
This value represents the number of speakers or subwoofers that the enclosure accommodates.
1
Box Style/Shape
The box style or shape refers to the actual shape of the box. Square and rectangular boxes are straight-edged boxes on all sides, whereas hatchback and truck style enclosures feature an angled front or back design that allows for installation in places short on depth such as single cab pickup trucks. You can also use such enclosures in hatchback cars or other vehicles where space is a premium. Tube and cylinder shaped boxes were made popular by Bazooka and are a great option for those looking for a nice amount of bass without sacrificing lots of space. They may even fit in locations that slim truck boxes cannot fit in. If the enclosure is vehicle specific, we encourage you to read the product description to find out which vehicles the enclosure is made for.
Square/Rectangle
Height
The height of the item, measured from top to bottom, in inches.
14-3/8"
Width
The width of the item from left to right (side-to-side) measured in inches.
15-9/16"
Depth
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
14-9/16"
Wood Thickness
The thickness of the wood the enclosure is made of, measured in inches.
3/4"
Number of Terminals
The number of terminals the enclosure has. Each terminal represents 1 positive and 1 negative.
1
Terminal Type
Spring clip terminals work best with bare wire connections with small-gauge speaker wire, or pin-type connectors.

Binding post terminals are a sturdier, more versatile type of speaker terminal. Because binding post terminals are are threaded, you can tighten them down against the wire or connector for a tight, clean connection. The most popular style of binding post terminals is known as a "5-way binding post". This type can accept bare wire, or any of the common speaker wire connectors. Binding posts with the option to be used with banana clips are even more versatile

Spring posts are a hybrid of the two. Instead of using a thread and "screwing" them tight, they use a spring to allow the wire to fit and tighten against the terminal.

Spring posts
Box Exterior Color
The color of the enclosure's exterior/outer finish.
Black
Box Finish
The material used on the outside of the box. Most boxes are carpeted to prevent exterior scratches; however vinyl is popular as it can often be color-matched to a near exact look of your leather factory interior.
Carpet
Final Wired Impedance
This is the final impedance of the system as the amplifier will see it. If the final impedance is for two sets, it means that the enclosure has two sets of terminals at the listed impedance.

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0
Tommy9

Nashville, TN

Overall
Durability
Value
Features
Design
Usability
Best Bang for Your Buck!

March 13, 2013

Blown away by the sound of this sub/amp combo and the value. Unless you want to win some competition, I cannot imagine why you would need anything more than this. The bass is tight and the amp barely gets warm. I have the gain about half way and it is plenty. I've had dual 12 inch kickers and a higher powered amp that didn't sound as good. Received from sonic in perfect condition in about a week. Definitely recommend!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Matthew

Reading, PA

Overall
Durability
Value
Features
Design
Usability
Cerwin Vega: Big Bang for the buck!

February 10, 2013

My ordering experience was very smooth. The installation went well and the equipment works excellent. I could not have found a deal this good at any local shops. This Cerwin Vega kit was a great buy! Thank you!

0 of 0 found this helpful

Help our customers find the most helpful reviews

johnathan

Camden, OH

Overall
Durability
Value
Features
Design
Usability
Great Deal!!!!

September 10, 2012

i absolutely love have fast it was shipped! excellent looking bass and amp, this is my first pro amp and sub! thank you i recomend cerwin vega!:)

0 of 0 found this helpful

Help our customers find the most helpful reviews

Big D

Ocala, FL

Overall
Durability
Value
Features
Design
Usability
Awesome Package!!!

March 20, 2012

I bought this bass package a little over 3 months ago. For the money you spend, the result is phenomenal!!! Great, tight bass from the sealed box. Plenty of juice to hit those rumbling lows, and a whole new experience in my little Civic sedan! I would definitely but this again!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Big D

Ocala, FL

Overall
Durability
Value
Features
Design
Usability
Awesome Package!!!

March 20, 2012

I bought this bass package a little over 3 months ago. For the money you spend, the result is phenomenal!!! Great, tight bass from the sealed box, plenty of juice to hit those rumbling lows, and a whole new experience in my little civic sedan! I would definitely but this again!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Brooklyntrin

Brooklyn ,NYC

Overall
Durability
Value
Features
Design
Usability
Nice unit

March 9, 2012

Yes nice unit good bass not too big not too small. I just have to fine tune the head set, thinking of adding an EQ to get the most out of it.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

HEDBK112

UPC

660715403154

Weight

38.55lbs

Internal SKU

hedbk112

Internal Product ID

39704

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Cerwin-Vega HEDBK112