Pack of Two 199 UF 100-Volt Non-Polar 10% Bass Blocker Capacitors
Pack of Two 199 uF Non-Polar 10% Bass Blocker Capacitors • Removes Selected Frequencies from the Audio Source • 100 Volts • Protects the Speakers from Receiving Damaging Frequencies • 200 Hz @ 4 Ohm
Learn more about the bb199Crossover Frequency (Hertz) | 8 Ohms | 4 Ohms | 2 Ohms |
80 | 248.44 uF | 496.88 uF | 993.75 uF |
100 | 198.75 uF | 397.50 uF | 795.00 uF |
120 | 165.63 uF | 331.25 uF | 662.50 uF |
150 | 132.50 uF | 265.00 uF | 530.00 uF |
200 | 99.38 uF | 198.75 uF | 397.50 uF |
280 | 70.98 uF | 141.96 uF | 283.93 uF |
400 | 49.69 uF | 99.38 uF | 198.75 uF |
600 | 33.13 uF | 66.25 uF | 132.50 uF |
800 | 24.84 uF | 49.69 uF | 99.38 uF |
1000 | 19.88 uF | 39.75 uF | 79.50 uF |
1200 | 16.56 uF | 33.13 uF | 66.25 uF |
2000 | 9.94 uF | 19.88 uF | 39.75 uF |
4000 | 4.97 uF | 9.94 uF | 19.88 uF |
5000 | 3.98 uF | 7.95 uF | 15.90 uF |
6000 | 3.31 uF | 6.63 uF | 13.25 uF |
8000 | 2.48 uF | 4.97 uF | 9.94 uF |
10000 | 1.99 uF | 3.98 uF | 7.95 uF |
12000 | 1.66 uF | 3.31 uF | 6.63 uF |
Internal Product ID:
40127
Simple
Great product, helps me save my door speakers some stress and installs in minutes with a couple butt connectors.
18
found this helpful.Does What its Supposed To
Installed with a late 80's Delco head unit to preserve original state of vehicle,In front of a new pair of JBL 3 1/2's they work great protecting and rolling off the low bass to my new 3 1/2's, Would definitely reccomend and do again as a cost effective fix.Just an FYI you have to either add yourf own spade connectors to the wire or solder, as they are not pre-prepped with spades like some.
18
found this helpful.must Buy
Didnt need much bass, these worked flawlessly for my 6X9
16
found this helpful.Dooes It's job
I have installed a subwoofer and needed to cut low freq on my cars door and rear speakers. I've got 2 pairs of thees blockers. They work as desired. Filters low frequencies and the speakers play without distorting even on high volume.
17
found this helpful.Works great, easy to use
Very easy to install, simple crimp with butt connectors is all you have to do, or solder if you have tools.
14
found this helpful.great product
great product would recommend it . works awesome easy install does the job.
12
found this helpful.not much difference
I would recommend maybe looking for a stronger blocker.. I see this says 10% or something like that.. You can tell a slight difference with this but more was needed for my usage at least..
Best selling similar products