Expert Service 1-877-289-7664 [Hours]

Ford F-150 1997-2012 Speaker Upgrade Kit

800W Realm Amplifier + 2 WCC680 6" x 8" / 5" x 7" 2-Way Convertible Component / Coaxial Car Speakers

We apologize

This item has been discontinued

Realm A400.4

400W 4-Channel Class A/B Car Amplifier
Quantity: 1

  • Realm by Scosche 4-Channel Class A/B Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 60 watts x 4 chan.
    • 2 ohms: 100 watts x 4 chan.
    • Bridged, 4 ohms: 200 watts x 2 chan.
  • MOSFET power supply
  • Power LED (blue) indicator
  • Multi-Color LED Protection:
    • Red: overload or circuit problem
    • Yellow: thermal problem
    • Green: low voltage problem
  • Soft Start Turn-on
  • 4/3/2 channel operation
  • 2-Ch/3-Ch/4-Ch input selector
  • Speaker-level (high-level) inputs
  • Preamp RCA outputs to daisy chain multiple amps
  • 4-Way System Protection circuitry
  • Illuminated dial controls
  • Discrete plug style terminals
  • Double sided glass-epoxy circuit boards
  • Internal transistor heat sinks for maximum heat dissipation
  • Input sensitivity:
    • Low level: 150mV-6V
    • High level: 325mV-10V
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • Variable high-pass filter (50-500 Hz, 12 dB/octave)
  • Variable low-pass filter (50-500 Hz, 12 dB/octave)
  • CEA-2006 compliant amplifier
  • Frequency response: 20-20,000 Hz
  • Dimensions: 13-13/16L x 9-13/16"W x 2-1/8"H
  • 8-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

West Coast Customs WCC680 (Same as Diamond Audio D673A)

6" x 8" / 5" x7" 2-Way Convertible Component/Coaxial Car Speakers System by Diamond Audio (D673A)
Quantity: 2

General Features:

  • 6" x 8" WCC Series Convertible Component Car Speaker System
  • Equivalent to Diamond Audio D673A speakers
  • Power Handling:
    • Peak: 240 watts per set / 120 watts each side
    • RMS: 120 watts per set / 60 watts each side
  • Component or Coaxial mounting configuration
  • Hard anodized Aluminum cone material
  • Rubber speaker surround for improved damping
  • 1" Aluminum Dome tweeter
  • 12db/octave passive external crossover network
  • 4 ohms impedance
  • High temperature voice coil
  • Rear acoustic fill provides matched attenuated output from front crossovers to the rear speakers
  • Flat progressive spider maintains linear cone movement
  • Rubber boot magnet protector
  • Top-mount depth: 2-1/8"
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

Priced Per Complete Component System: 2 midwoofers, 2 tweeters and 2 crossover networks.

Stinger SK6281

8 Gauge 6000 Series Power Amplifier Installation Kit
Quantity: 1

Product Features:
  • 8 Gauge 6000 Series Power Amplifier Wiring Kit
  • Designed specifically for car audio systems up to 400 watts
  • Premium power and ground wire provides optimal power transfer
  • Made from 100% oxygen-free copper for a pure uninterrupted transfer of power
  • Mini-ANL style fuse holder for maximum power delivery and safety
  • Pre-Installed black nylon mesh covering protects power & ground wire from damage
  • TruSpec cables/wires meet or exceed the industry standard of copper required for the gauge size
  • Matte finish HyperTwist wire construction provides excellent flexibility
  • Pre-Terminated power connections provide reliable performance
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty
Package Includes:
  1. 17 ft. of 8 Gauge matte blue hyper-twist power wire
  2. 3 ft. of 8 Gauge Matte silver hyper-twist ground wire
  3. 17 ft. of 18 Gauge Blue turn-on wire
  4. 70 Amp Mini-ANL fuse
  5. Mini-ANL Style fuse holder
  6. Pre-Terminated ends
  7. Mesh wire loom
  8. Stinger metal badge
  9. Includes installation accessories

EFX FS9W-25FT by Scosche

Precut 25 ft Piece of FLux 9 Conductor Speed Wire Speaker Cable
Quantity: 1

  • Flux 9 Conductor Speed Wire Speaker Cable
  • Contains 9 Individually jacketed wires, all conveniently enclosed in a outer PVC jacket
  • Meets the American Wire Gauge (AWG) standards
  • Tin plated oxygen free copper prevents oxidation and improves reliability
  • Used primarily for OEM integration
  • Color coded to match the standard aftermarket wires
  • Wire gauge: 18 AWG
  • Contains enough wire strands for 4 speakers and a amplifier turn-on wire
  • True to gauge for optimal performance
  • Length: 25 ft.
  • Authorized Internet Dealer
  • 1-year Manufacturer's warranty

Front Speaker Specifications

Speaker Size
Refers to the size of the speaker measured in inches. Every vehicle has standard application sizes. Please use our vehicle fitment guide for your vehicle's specific speaker sizes if you do not know them.
6" x 8" (also mounts in most 5" x 7" locations)
Design
The number of individual drivers in a car speaker. Speakers with 2 drivers are known as a 2-way, and 3 drivers are known as a 3-way. Component systems are often referred to as "separates" because the tweeter is not attached to the midwoofer (main speaker driver) and mounts separately in a location such as a door post. Component systems typically come with an external crossover so you can easily adjust the high and low frequencies sent to both the midwoofer and the tweeter. Center channel speakers are great for those looking to have surround sound in their vehicle.
2-way Component System
Shallow Mount Installation
This means that the subwoofer/speaker is designed to be installed in areas that do not have a lot of space. Shallow mount subwoofers are typically found under a seat or behind the seat in some trucks.

Shallow mount speakers will typically have a mounting depth of 2" or less, while shallow mount subwoofers will typically have a mounting depth of 3" or less.

No
Tweeter Design
Designs such as cone, dome, semi-dome, balanced dome, and whizzer are most popular. Cone tweeters are simple, efficient and typically are the most reasonably priced. Dome tweeters are used in most home speakers, and provide a smoother and more accurate sound. Semi-dome design is one with a dome placed inside a cone. A Balanced dome driver is a semi-dome with equal reproduction area given the cone and dome portions of the driver. A whizzer tweeter is a separate tweeter cone driven by the voice coil of the woofer.
Dome
Tweeter Composition
Materials such as polypropylene, silk, cloth, and paper are the most common, where as many more recent tweeters are now manufactured with composites such as Aluminum, Titanium, Mylar, and other materials.

PEI is an acronym for "Polyetherimide" which is an amorphous, amber transparent, high-performance thermoplastic.

Aluminum
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Aluminum
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Rubber
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
120 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
60 watts
Sensitivity
An efficiency or sensitivity rating tells you how effectively a speaker converts power into sound. The higher the number, the more efficient the speaker and the louder it will play with the same input power. An efficient speaker helps you maximize your available power. Most sensitivity ratings measure the speaker's output with 1 watt of input, 1 meter from the speaker. Some speakers' sensitivity is measured with 2.83 volts of input, instead of 1 watt.
 
Efficiency (1w/1m) is not an accurate indicator of a subwoofer's output capability and should not be used as a comparison to other speakers or subwoofers to determine which one is "louder".
86.5 dB
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
2-1/8"
Cutout Dimensions
Refers to the dimensions of the hole, measured in inches or millimeters, required to contain the speaker.
4-15/16\" x 6-15/16\" 

Amplifier Power Specifications

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

60 watts x 4 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

100 watts x 4 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

200 watts x 2 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
4
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

400 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
8 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
2 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
4 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.03%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 500 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 500 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
90 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
No
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
50A x 1 
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

Yes

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0

Accessory Tools and Products

Accessories added

NVX Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Big 3 Upgrade Kit 1/0 gauge with EnvyFlex cable, wire cutters, 2 battery and 4 ring terminals.

Your Price $134.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

This Big 3 Kit features HyperFlex cable and comes with everything you need to upgrade your factory power and ground wire.

Your Price $149.99

XS Power BIG3XS 1/0 Gauge Big 3 Upgrade Kit

The XS Power Big 3 Kit features 100% OFC XP Flex cable and includes everything you need to upgrade your factory power and ground wire.

Your Price $99.99

XS Power BIG3XP 1/0 Gauge Big 3 Upgrade Kit

The Big 3 Kit comes with everything you need to upgrade your factory power and ground wire.

Your Price $49.99

Product Summary

Manufacturer

Model Number

2-WCC680_A400.4

Weight

27.84lbs

Internal SKU

2-wcc680_a4004

Internal Product ID

60989

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Ford F-150 1997-2012 Speaker Upgrade Kit

  • How to Install a Car Amplifier
  • Sonic Electronix: The X Factor when Shopping Electronics