Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Boss BLX4000

4000W Max, Blade Exxtreme Series High-Current 2-Channel Amplifier (BLX-4000)

Discontinued
|

We apologize

This item has been discontinued

  • 4000 watts MAX, Blade Exxtreme Series 2 Channel Amplifier
  • RMS Power Rating
    • 4 ohms: 500 watts x 2 chan.
    • 2 ohms: 900 watts x 2 chan.
    • 1 ohm: 1500 watts x 2 chan.
  • Remote Subwoofer Level Control
  • High Input Wire
  • Operable in Tri-Mode
  • Various Protections: Thermal and Speaker Short Protection
  • Variable Low and High Pass Crossovers
  • MOSFET Power Supply
  • Frequency Response: 9 - 50,000 Hz
  • Dimensions: 23"L x 11 5/16"W x 2 3/8"H
  • 1-year Manufacturer's warranty

Product History:

Boss BLX4000 thumbnail
(newest, current model)
Boss PD-4000 thumbnail
(previous model, replaced by Boss BLX4000)

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

500 watts x 2 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

900 watts x 2 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

1500 watts x 2 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

4000 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

AB
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
2
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

4000 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

3000 watts
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
1 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
2 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
.01%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
Yes
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
High-pass (HP)
Full (AP)
High-Pass Crossover Frequency
The high-pass crossover frequency can be a fixed crossover point or a variable crossover range. A variable high-pass crossover allows you to select a specific crossover point which allows frequencies above the set crossover point to pass, while making frequencies below the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

120 - 700 Hz
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

45 - 100 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
105 dB
Channel Separation
Also referred to as crosstalk. The amount of interference on one stereo channel caused by the leaking of the other stereo channel. The higher the rating in decibels (dB), the better the Channel Separation.
90 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
40A x 5 

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
50%
4 Star
50%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
4.5
Value
4.5
Features
4.5
Design
4.0
Usability
5.0

taterbug

gainesvilles ga

Overall
Durability
Value
Features
Design
Usability

my boss blade blx 4000

January 23, 2012

This is a over all good amp i have had mine for about 3-1/2 years the only problem that i have out of mine is the hot an ground wire get's so hot that thay melted the wire holder. I'm serching for a spare one now.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Nathan

Woodlands, TX

Overall
Durability
Value
Features
Design
Usability

Great for a medium power source!

October 10, 2007

Great, simple amp for good power. Its worth the money as long as you use it in a 1 ohm load or you could find something better, otherwise I`m satisfied with this...

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB0

1/0 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft 2-Channel RCA Audio Interconnect Cable with Twisted Pair Construction

Your Price $11.99

Kicker Q-Series RCA Interconnect Cable

16.5 ft. of 2-Channel Interconnects with twisted pair conductors, K-cut gold plated contacts, and hyper-flex technology for easy installation!

Your Price $32.95

NVX XIX25 X-Series Interconnect Cable

16.4 ft. of 4-Channel X-Series RCA Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $26.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

XIX2025 Strapping RCA

0.25 Meter (0.86 ft) Hyper-Flex RCA cable w/ Serpentine-Cut Nickel Plated Connectors

Your Price $12.99

Product Summary

Manufacturer

Model Number

BLX4000

UPC

791489104326

Weight

22.00lbs

Internal SKU

blx4000

Internal Product ID

6669

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Boss BLX4000