Expert Service 1-877-289-7664 [Hours]

Diamond Audio TDX10D4

TDX Series 10" Dual 4 ohms Subwoofer

Discontinued
|

We apologize

This item has been discontinued

  • 10" Dual 4 ohms Subwoofer
  • Power Handling:
    • 800 watts RMS
    • 1000 watts Max
  • Kevlar/Nomex Honeycomb/Kevlar 3 Layer Cone
  • Nitrile Butadine Rubber Surround
  • Dual mirrored, progressive, poly-aramid, spiders with lead wires woven in place
  • Encapsulated Motor Case with Thermally Conductive Grease
  • Segmented Neodymium Motor Structure
  • One-Piece Die-Cast Aluminum Frame with Integral Radial Heat Sink Fins
  • Massive Dual Copper Voice Coils with Insulation Wound on Hard Anodized Aluminum Former
  • Neodymium Magnets
  • Massive Vented Pole Piece
  • 1-year SonicElectronix.com warranty

Subwoofer Specifications

Subwoofer Size
Refers to the diameter of the subwoofer, measured in inches.
10"
Peak Power Handling
Peak power handling refers to the amount of power a speaker can handle during a brief musical burst. The RMS power range figure is a much more reliable rating for determining the speaker's power requirements. The Peak power handling specification is typically rated per speaker unless otherwise noted.
1000 watts
RMS Power Handling
The RMS power is the amount of power the speaker requires to operate safely and properly. RMS Power Handling refers to the amount of power a speaker can handle on a continuous basis. We recommend powering your speakers or subwoofer with 80%-120% of its recommended RMS rating. The RMS power handling specification is typically rated per speaker unless otherwise noted.
800 watts
Voice Coil(s)
Dual voice coil subs have more wiring flexibility than single voice coils subs; however, single voice coil subwoofers provide easier hookup options for wiring multiple subwoofers in parallel or series. You may also run a dual voice coil (DVC) sub in parallel, series, or combination. A quad voice coil has four voice coils and is equal to two dual voice coil subwoofers as far as wiring goes.
Dual
Impedance (Per Voice Coil)
The load value (in ohms) that the speakers present to the amplifier per voice coil - the amount of resistance to the current flow. This is a key specification as subs wired in parallel or low impedances can create problems with your amplifier and potentially void all warranties. We encourage you to ask our support department prior to purchase if you do not understand which impedance level will suit your application best.
4 ohms
Xmax (millimeters)
Typically measured in millimeters, the Xmax value is the measure of a speaker cone's maximum excursion in one direction while maintaining a linear behavior.
22 mm
Woofer Composition
Lightweight woofer cone materials are essential for efficient operation. Poly cones produce exceptional sound and are sturdy against various changes in temperature. Paper cones are very efficient, and when treated for moisture resistance, will perform at a high level. Poly refers to polypropylene, which is thermoplastic or fibers that are polymers of propylene. IMPP refers to injection molded polypropylene, a commonly used process and material in speakers.
Kevlar/Nomex Honeycomb/Kevlar
Woofer Surround
A speakers surround is part of the suspension system. The surround protects the cone and prevents it from being displaced as it flexes out from the basket. It is usually made of a durable material like treated foam or rubber in order to withstand the strenuous job of producing bass frequencies.
Nitrile Butadine Rubber

Recommended Enclosure Specifications

Top-Mount Depth
The depth when installed on top of the mounting surface. Measured from the bottom of the speaker's magnet to the bottom of the mounting holes on the rim of the speaker.
7.52"
Cutout Diameter
The actual diameter of the hole you will need to cut out if you are creating a new mounting location for this speaker, or if you are mounting a subwoofer in a box.
9.98"

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0

Chriss

Austin texas

Overall
Durability
Value
Features
Design
Usability

Hit

April 7, 2012

These hit so hard I have them on a 3500 Watt crunch amp and they rattle the front doors in my car. Can't go wrong with these subs.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX 25 ft. of True Spec 12 Gauge Speaker Wire

100% OFC wire with EnvyFlex metallic jacket insulates and protects against damage from extreme conditions.

Your Price $39.99

25 ft. of Streetwires 12 Gauge Speaker Cable

You'll need speaker wire to hook up that new subwoofer!

Your Price $44.95

Belva 23 ft. of 12 Gauge Speaker Wire

Ultra-flexible PVC blended jacket for easy installation.

Your Price $14.99

40 Square Feet of Sound Dampening Material

Thicker than the competition, complete sound damping kit for entire vehicle! Use for trunk, doors, roof and floor.

Your Price $119.99

Dynamat Sound Dampening Bulk Kit

Did you know sound dampening will reduce those annoying rattles and even increase your SPL?

Your Price $159.95

Stinger Sound Dampening Bulk Kit

Stinger's Roadkill sound dampening series is sure to kill unwanted road noise and rattles! Enough sound dampening for the whole car!

Your Price $99.99

Spring Post Terminal Cup

Makes adding a spring post terminal to an enclosure simple! Banana clip ready!

Your Price $3.99

40" x 15 Ft Piece of Premium Un-Backed Automotive Trim Carpet

Durable design for long life-span, available in many colors and shades.

Your Price $39.99

Gold Plated Dual Terminal Banana Plug Connector

Enables an expandable, secure connection accepting up to 8 gauge wire.

Your Price $3.99

Car Stereo and Speaker Installation Tool Kit

Includes Test Light, Crimp/Splice Tool, Multi-bit Screwdriver and more.

Your Price $12.99

Xscorpion 9-Piece Nylon Plastic Pry and Chisel Tool Set

Easily removes dash/trims, door clips, panels and pins, rubber grommets and vehicle emblems.

Your Price $14.99

Cordless Multi-Functional Heat Tool Soldering Iron Kit

Continuous working lock allows you to work without holding down trigger.

Your Price $79.99

2" Universal, Professional Heavy Duty Roller for Sound Damping/Dampening

Universal rubber roller to make it easy to install sound dampening.

Your Price $7.99

1mm All Purpose Solder

Solder is all purpose for use on most projects where solder is needed.

Your Price $8.99

Scosche SPL Meter

Monitor the noise level of your new car audio system with this SPL meter measuring from 60-135 dB.

Your Price $21.99

AutoSound 2000 CD-101

Low frequency test CD

Your Price $11.99

Impedance Meter / Signal Generator

Easy to locate tuning frequencies of passive radiators and ported enclosures

Your Price $299.99

1 Diamond Audio TDX10D4 Subwoofer

Mono Amp

2 Channel Amp - Bridged

2 Diamond Audio TDX10D4 Subwoofers

Mono Amp

Mono Amp - Option 1

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp - Bridged

3 Diamond Audio TDX10D4 Subwoofers

Mono Amp

4 Channel Amp

4 Diamond Audio TDX10D4 Subwoofers

Mono Amp

2 Channel Amp

2 Channel Amp - Bridged

4 Channel Amp

Product Summary

Manufacturer

Model Number

TDX10D4

Weight

25.00lbs

Internal SKU

tdx10d4

Internal Product ID

6981

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Diamond Audio TDX10D4