Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Hifonics XX-THOR

3000 watts, Class D MonoBlock Amplifier

Discontinued
|

Good news and a little bad...

This item has been discontinued

But you may be interested in the newest model that's available.

xxvthor thumbnail

Hifonics XXV-THOR

OUR PRICE: $669.99

View item
  • 3000 watts, Class D MonoBlock Amplifier
  • RMS Power Output:
    • 1 ohms: 3000 watts x 1 channels
    • 2 ohms: 2300 watts x 1 channels
    • 4 ohms: 1200 watts x 1 channels
  • Ultra D-Class amplifier Topography for low-heat operation
  • Link and Sync: Link two amps to double output power
  • Complementary/Balanced high-speed MOSFET output devices
  • PWM MOSFET EXVP (Exponential Vari-Power Supply)
  • SPC Twin Turbo-Torroids with simpatice coil design
  • 9-Volt Gold unbalanced RCA line-level inputs
  • 18-Volt balanced line inputs with optional Hifonics MM-BLD-1
  • Full-range RCA line-level outputs
  • Fully adjustable Accu-Cross crossover includes: Low-pass, Subsonic, and Phase adjustments
  • Variable bass boost (+18 dB)
  • Hifonics remote bass control included
  • Gold dual 2-gauge power and ground connectors
  • Dimensions: 11-1/5"L x 20.5"W x 2-3/5"H
  • 1-year SonicElectronix.com warranty

Product History:

Hifonics XXV-THOR thumbnail
(newest, current model)
Hifonics XX-THOR thumbnail
(previous model, replaced by Hifonics XXV-THOR)

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

1200 watts x 1 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

2300 watts x 1 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

3000 watts x 1 channels
Bridged RMS Power

Bridging refers to combining two channels on an amplifier to create one channel with double the voltage and an increased power output. A 2-channel amplifier will bridge down to 1-channel and a 4-channel amplifier can bridge to create 2-channels. An amplifier is most commonly bridged to drive a subwoofer.

Remember, once you bridge two channels down to one its final impedance will be 4 ohms unless otherwise specified. This rating lists the RMS power created once an amplifier is bridged.

Not Bridgeable

Amplifier Specifications

Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

3000 watts
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
1 ohms
Minimum Impedance Bridged
The lowest impedance the amplifier will handle when it is bridged.
Not Bridgeable
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
<0.1%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
2 pairs
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

24 dB ( 35-250 Hz)
Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
24 dB ( 15-35 Hz)
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
>95 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
+18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Yes
Fuse Rating
The amperage and the number of fuse(s) an amp requires.
300 Amps

Warranty and Return Policy

Parts Warranty Duration
Not warranted
Labor Warranty Duration
Not warranted
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
5.0
Value
5.0
Features
5.0
Design
5.0
Usability
5.0

Rody

Germany

Overall
Durability
Value
Features
Design
Usability

WOW!

March 14, 2009

This is by far the best amp i have ever used. Props to Hifonics!!!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Parmijit

Canada

Overall
Durability
Value
Features
Design
Usability

insane amp

January 24, 2008

i have recently purchased this amplifier it is by far one of the best amplifiers out right now

0 of 0 found this helpful

Help our customers find the most helpful reviews

TJ

Greenfield, IN

Overall
Durability
Value
Features
Design
Usability

One good Amp

July 13, 2007

I bought this amp and had it hooked up within about an hour of when I got it. It is a very good amp for the money i would have paid more for the amp but the price is very good it is good amp that will rattle your car with the rite sub.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB0

1/0 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft of V-Series 2-Channel RCA Audio Premium Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $11.99

NVX XIX25 X-Series RCA Interconnect Cable

16.4 ft. of 4-Channel X-Series RCA Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $26.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

XIX2025 Strapping RCA

0.25 Meter (0.86 ft) Hyper-Flex RCA cable w/ Serpentine-Cut Nickel Plated Connectors

Your Price $12.99

Product Summary

Manufacturer

Model Number

XX-THOR

UPC

806576213703

Weight

31.00lbs

Internal SKU

xxthor

Internal Product ID

8426

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Hifonics XX-THOR