Expert Service 1-877-289-7664 [Hours]

2nd Annual Warehouse Sale!

Memphis 16-PR1.500

Power Reference PR Series Class D Monoblock Amplifier

Discontinued
|

We apologize

This item has been discontinued

  • Power Reference PR Series Class D Monoblock Car Amplifier
  • RMS Power Rating:
    • 4 ohms: 150 watts x 1 chan.
    • 2 ohms: 300 watts x 1 chan.
    • 1 ohm: 500 watts x 1 chan.
  • Optional: Wired remote bass level control available, sold separately.
  • Bass Boost: 0-18 dB at 45 Hz
  • Variable low-pass filter: 50-350 Hz
  • Subsonic Filter: 20-50 Hz
  • CEA-2006 compliant amplifier
  • 1 Pair Preamp Outputs
  • Sensitivity: 90 dB
  • Frequency response: 10-400 Hz
  • Dimensions: 12.6"L x 10"W x 2.3"H
  • 1-year parts only warranty by Sonic Electronix (any labor related warranty charges are the responsibility of the customer)

Product History:

Memphis 16-PR1.500 thumbnail
(newest, current model)
Memphis 16-PRD500.1 thumbnail
(previous model, replaced by Memphis 16-PR1.500)

Power Specifications - Full Range Channels

RMS Power @ 4 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 4 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

150 watts x 1 channels
RMS Power @ 2 ohms

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 2 ohms, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

300 watts x 1 channels
RMS Power @ 1 ohm

The RMS power rating is the measure of continuous power that an amplifier can output, or a speaker can handle. It is the most accurate depiction of real, continuous power that the industry has so far.

If the final impedance of your speakers or subwoofers equals 1 ohm, this is how much power this amplifier will supply at that ohm level. The higher the RMS wattage, the more clean and loud your music will sound.

500 watts x 1 channels
Peak Power Output
This form of power rating refers to the maximum amount of power an electronic device can handle or output in an instant without damage occurring. Often times this maximum is achieved during a brief musical burst, such as a drum accent, or low bass hit.

Some manufacturers display peak power ratings on the face of their products to increase the appeal to consumers. The RMS power rating is more accurate, and we recommend using it for product comparison.

1000 watts x 1 channels

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Number of Channels
Each channel on an amplifier will power one speaker using a positive and negative cable. There are various types of amplifiers, each designed to power a certain number of speakers. Monoblock amplifiers, also known as single channel, are designed to power one or more subwoofers. These amplifiers often have very high power ratings. On the other hand, multi-channel amplifiers power multiple speakers, usually at lower power ratings. 2-Channel and 4-Channel amplifiers can power car speakers or low powered subwoofers. Occasionally you might see a 5 or 6-channel amplifier that can power speakers and subwoofers at the same time. The most common setup is a monoblock amp to run subwoofers and a 4-channel amp to run door speakers. Check out our Knowledge Base for more information.
1 - Mono
Total Peak Power Output
The total peak power output is measured as the wattage per channel multiplied by the number of channels, and is calculated at the lowest level of operating impedance.

It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.

The RMS power rating is more accurate, and we recommend using it for product comparison.

1000 watts
Total RMS Power Output
Total RMS power is measured by multiplying RMS power per channel by the number of channels, and is calculated at the lowest level of operating impedance.

RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.

The RMS output figure is much more accurate than the peak rating when comparing products.

500 watts
Maximum Input Gauge Size
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
4 AWG
Minimum Impedance Unbridged
The lowest impedance the amplifier will handle when it is not bridged.
1 ohms
THD at Rated RMS Power
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.75%
Speaker Level Inputs
Speaker level inputs are commonly referred to as high-level inputs and vice versa. This input type allows you to get your audio signal directly from the speaker wire in your vehicle, instead of using RCA cables. The advantage of this is factory integration, as most stock radios do not have RCA outputs to run amplifiers.
No
Preamp Outputs
Many amplifiers are equipped with RCA preamp outputs which pass the original music signal from the source to additional amplifiers. This is known as daisy chaining because the source connects to the first amp, and the first amp connects to the second amp, etc. The advantage to daisy chaining is you only need one 2-channel RCA cable to transfer the signal from the head-unit to the amplifier, and then one additional cable for each amp being daisy chained.
1 pair
Built-in Crossover

A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.

When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.

Low-pass (LP)
Low-Pass Crossover Frequency
The low-pass crossover frequency is typically used for subwoofers. It can be a fixed crossover point or a variable crossover range. A variable low-pass crossover allows you to select a specific crossover point which allows frequencies below the set crossover point to pass, while making frequencies above the set point gently or harshly roll-off, depending on the steepness of the slope.

The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.

50 - 350 Hz
Subsonic Filter
Allows you to block (filter) ultra-low frequencies that your subs cannot reproduce.
20 - 50 Hz
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
90 dB
Bass Boost
The objective of the bass boost is to get more kick out of your subwoofer. It is a circuit that emphasizes the lower frequencies at a given point. The bass boost should always be set first before setting the gain. This feature is known for destroying subwoofers and is commonly used incorrectly, so be cautious.
0 - 18 dB
Bass/Gain Remote
If the amp comes with a bass/gain remote you will be able to control the level of your bass from your dashboard. Typically bass remotes also include a 16-20 ft. wire for installation.
Optional (Accessory required and sold separately)
Fan Cooled
A great feature to have if an amp generates a large amount of heat. Cooling fans can help regulate the temperature to prevent the amp from overheating (burning).
No
CEA-2006 Compliant
Amplifiers that have been tested to meet specific standards. When a car amplifier meets these standards, you can be sure that it will be able to produce the amount of power specified by the official CEA-2006 rating. Usually, these rating consist of the following items:
  • RMS Power
  • Signal-to-Noise Ratio

This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.

No

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Sonic Electronix

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
4.8
Value
4.0
Features
4.5
Design
4.3
Usability
4.8

ross

mn

Overall
Durability
Value
Features
Design
Usability

best in its class

July 7, 2012

Have this amp and it delivers incredible sound. Have it on one L7 and it beats hard.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Corey

Aiken, SC

Overall
Durability
Value
Features
Design
Usability

Best bang for the buck

May 14, 2009

I have this amp running my two JL Audio 12" W3-V2s..this amp has an incredible sound. The loudest I've ever had my subs. My amp is only on half volume and the sub level on kenwood headunit is left between -11 to -5 and is insanely loud. I've won a few local competitions. This is a great amp

0 of 0 found this helpful

Help our customers find the most helpful reviews

Slick

El Paso, TX

Overall
Durability
Value
Features
Design
Usability

The Best of the Best

December 20, 2008

This is an incredible amplifier! Never thought that this amp would be able to power my 15" Audiobahn subs. I recommend anyone to purchase this amp. Memphis is the best hands down.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Thomas

phenix city, AL

Overall
Durability
Value
Features
Design
Usability

Its Great

July 11, 2008

I have one of these amps and they are great. this amp beats all others if your like "only 500 watts " i said the same thing this made my subs hit harder then when i have an audiobahn 800 watt mono amp . its worth every penny !

0 of 0 found this helpful

Help our customers find the most helpful reviews

Anthony

Ardmore, OK

Overall
Durability
Value
Features
Design
Usability

Yes

July 3, 2008

I had this amp for over 6 months and it worked great for that time. It puts out every amount of power it says it does. The amp would always stay cool and I could have the gain half way up and it would barely get warm. This amp has a very good cooling fan to keep it cool as well. The only problem about this amp is the price. Your paying about double the price for this amp compared to the others but this amp will never overheat or break on you like others. So in the end you are saving money.

0 of 0 found this helpful

Help our customers find the most helpful reviews

Joseph

Spencerport, NY

Overall
Durability
Value
Features
Design
Usability

Sweet

August 29, 2007

This is by far one of the best amplifiers I have ever come across in it's range. Sure, it may not be the cheapest, but for what you're getting, it's worth every penny. I've seen this in action and it delivers. The thing never gets warm either! If you have the money for this amplifier, I highly recommend this amplifier!

0 of 0 found this helpful

Help our customers find the most helpful reviews

Accessory Tools and Products

Accessories added

NVX XKIT42 100% OFC True 4 Gauge Wiring Kit with RCA Cables and Speaker Wire

The reviews speak for themselves, this is awesome wire with everything you need!

Your Price $89.99

Stinger SK4641 4 Gauge Wiring Kit

Get a high quality amp kit from Stinger to get the most from your new amp!

Your Price $64.99

Belva BAK42 4 Gauge Amplifier Installation Kit

Great amps need great wire at a great price. This amp kit has everything you need!

Your Price $29.99

NVX XBG3PK 1/0 Gauge OFC Big 3 Upgrade Kit

Comes with everything you need to upgrade your power and ground wire.

Your Price $79.99

Kicker Big 3 Package 1/0 Gauge Big 3 Upgrade Kit

Get all you need including wire cutters to upgrade your power and ground wire.

Your Price $149.99

Belva BBG3KT CCA 1/0 Gauge Big Three Kit

Features everything needed to upgrade factory power and ground wire.

Your Price $39.99

StreetWires FB4

4 AWG / 4 Gauge Firewall Bushing

Your Price $6.95

NVX XDBU4 - Top of the Line!

Distribution Block with Two 1/0 or 4 AWG Inputs and Four 4 or 8 AWG Outputs

Your Price $17.99

Professional Installation for your Car Power Amplifier

Covers labor charges through our professional installer network.

Your Price $89.99

Kicker KI24 K-Series RCA Audio Interconnect Cable

4 Meters (13 ft.) 2-Channel K-Series RCA Audio Interconnect Cable

Your Price $16.95

NVX XIV25 V-Series 2-Channel RCA Cable

16.4 ft of V-Series 2-Channel RCA Audio Premium Interconnect Cable with Dual Twisted Pair Hyper-Flex Technology

Your Price $11.99

NVX XWS1225 12 AWG Speaker Wire

25 ft. of True 12 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $39.99

NVX XWS1625 16 AWG Speaker Wire

25 ft. of True 16 Gauge 100% Copper EnvyFlex Speaker Cable/Wire

Your Price $13.99

Belva BBSW127 12 AWG Speaker Wire

12 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $14.99

Belva BBSW167 16 AWG Speaker Wire

16 Gauge 7 Meter (23 Ft) Speaker Wire (CCA)

Your Price $12.99

The Install Bay IB-CAP1F

True 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $37.99

e2 ECAP1 by Scosche - Mid-Level 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $49.99

Rockford Fosgate RFC1D - Top of the Line 1 Farad

Digital 1.0 Farad Car Audio Capacitor for up to 1000W Max

Your Price $104.99

Scosche SPL Meter SPL1000F

Handheld boomSTICK measures your SPL range from 60 to 135 dB

Your Price $21.99

AutoSound 2000 CD-102

High Frequency Test CD specifically designed for the set-up and evaluation of sound system imaging and placement.

Your Price $11.99

AutoSound 2000 CD-104

Audiophile reference series test disc for evaluation of all audio components.

Your Price $11.99

Product Summary

Manufacturer

Model Number

16-PR1.500

UPC

702588118824

Weight

13.00lbs

Internal SKU

16pr1500

Internal Product ID

9927

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Memphis 16-PR1.500