See all parts that fit your 1998 X-90
2 ohm Removable Voice Coil Replacement Kit for SPG555-2 Subwoofer
Product highlights
Replacement voice coil assembly for SPG555 Subwoofers with 2 ohm impedance • Allows you to repair your SPG555-2 subwoofer on the spot • Can also be used to convert a 4 ohm SPG555 subwoofer into a 2 ohm model
Learn more about the spg555vc2
600W Peak (200W RMS) 6.5” CS Series 2 Way Coaxial 4-ohm Speakers
$79.96
List price $119.99
360W Peak (120W RMS) 6.5" Club Series 2-way Coaxial 3-ohm Speakers
$99.95
List price $139.95
480W Peak (120W RMS) 6.5” DS Series 2-way 4-ohm Coaxial Car Speakers (DSC6504)
$84.99
List price $94.99
600W Peak (200W RMS) 6.5" DB+ Series 2 Way Coaxial 4-ohm Car, Marine and Powersports Speakers
$109.00
List price $119.99
600W Peak (300W RMS) 6.5" Mille PRO Series 3-way 4-ohm Component Speaker System
$999.99
List price $1175.00
250W Peak (200W RMS) 6.5″ PNW Series 2 Way Component 3-ohm Speakers
$319.00
List price $339.00
600W Peak (70W RMS) 6.5" XED Series 2-Way Coaxial 4-ohm Speakers
$49.99
List price $59.99
600W Peak (300W RMS) 6.5" PRO Series Full Range Coaxial 4-ohm Speakers
$189.99
List price $227.99
Rockford Fosgate Power T2 T2652-S
400W Peak (200W RMS) 6.5" Power Series 2 Way Component 4-ohm Speaker System
$449.99
Best selling similar products
• Kits are assembled to ensure perfect fitment and alignment
• Each kit includes all new soft moving parts
• Impedance: Dual 2-ohm
• CA glue adhesive is NOT included
$109.99
List price $131.99
• 15" SoloX Series Dual 2-ohm Recone Kit
• Pre-assembled cone, surround, and voice coil
• Impedance: Dual 2-ohm
• Alignment shims are included for installation
$249.99
List price $279.99
• Kits are assembled to ensure perfect fitment and alignment
• Each kit includes all new soft moving parts
• Impedance: Dual 4-ohm
• CA glue adhesive is NOT included
$109.99
List price $131.99
• 12" SoloX Series Dual 1-ohm Recone Kit
• Pre-assembled cone, surround, and voice coil
• Impedance: Dual 1-ohm
• Alignment shims are included for installation
$239.99
List price $259.99
• 10" SoloX Series Dual 1-ohm Recone Kit
• Pre-assembled cone, surround, and voice coil
• Impedance: Dual 1-ohm
• Alignment shims are included for installation
$219.99
List price $239.99
• 10" SoloX Series Dual 2-ohm Recone Kit
• Pre-assembled cone, surround, and voice coil
• Impedance: Dual 2-ohm
• Alignment shims are included for installation
$219.99
List price $239.99
• Kits are assembled to ensure perfect fitment and alignment
• Each kit includes all new soft moving parts
• Impedance: Dual 2-ohm
• CA glue adhesive is NOT included
$159.99
List price $191.99
• 8" SoloX Series Dual 1-ohm Recone Kit
• Pre-assembled cone, surround, and voice coil
• Impedance: Dual 1-ohm
• Easy installation, glue is not included but required
$129.99
List price $149.99
• Kits are assembled to ensure perfect fitment and alignment
• Each kit includes all new soft moving parts
• Impedance: Dual 2-ohm
• CA glue adhesive is NOT included
$149.99
List price $179.99
• Kits are assembled to ensure perfect fitment and alignment
• Each kit includes all new soft moving parts
• Impedance: Dual 1-ohm
• CA glue adhesive is NOT included
$149.99
List price $179.99
Manufacturer:
Model Number:
SPG555-VC2
Weight:
4.00lbs
Internal SKU:
spg555vc2
Internal Product ID:
20006
| 5 star |
|
67% |
| 4 star |
|
33% |
| 3 star |
|
0% |
| 2 star |
|
0% |
| 1 star |
|
0% |
| Durability | ||
| Value | ||
| Features | ||
| Design | ||
| Usability |
Awsome sub!
The birthsheet on my MTX amp says 1308 watts, so I set the gain for 51.2 volts at max volume at 40hz. With a 2 ohm DC nominal load, the average AC wattage (RootMeanSquare) dissipated on my subs voice coil at 40hz is 1308. This sub has taken it, and stays cool doing it after break in. I've recorded temps as high (with non contact LASER thermometer) as 212 degrees (boiling point of water) on the plastic of the voice coil without failure. Now, with same Bass Mechanix after break in, the same area measures around 120 degrees. I have melted on of these voice coils, but that was running the amp with too much gain, clipping the signal. On a road trip, after my amp failed, and replaced with MTX but no volt meter or oscilloscope to set up. One piece of advice, after abuse and over tightening the 2 screws that conduct the current to the voice coil and also secure the voice coil, the solder joint between the hollow rivets that are the screw holes that connect to the flat voice coil leads will fail. You just need a good solder gun, and heat up the flat part of the lead (after fluxing the rivet), and get some solder to suck between the rivet and flat lead. Better than new. Also hex screws can strip, cheap China, so get a high quality 2.5mm Allen head screw gun bit and use a 1/4 inch drive socket and socket driver handle (looks like screwdriver handle). Easier to gauge ultimate torque being applied with screwdriver handle. I have used threadlocker. You need high temp cause the two that conduct electricity for the voice coil consequently also conduct heat, so anything but high temp fails. Unfortunately, high temp also means high strength. I had to cut my last cone apart to get my cutoff tool in to cut shaft off Allen head voice coil fastener so I could remove a functioning voice coil.
19 found this helpful
Excelent complement for the SPG555 subwoofer
I bought two additional VC's just to be safe, as I'm feeding the SPG555 more watts rms than it's rating (1380wrms). It's great to be able to change voice coils without opening the box or taking the sub apart.
17 found this helpful
Great Value!
Easy to use! It does what it got to do!
16 found this helpful
Cancel
Modern vehicles often require specific brackets, wiring harnesses, and mounting solutions. A fit guide ensures:
Whether you're replacing a factory stereo or upgrading your entire audio system, the Fit Finder eliminates uncertainty.
