Expert Service 1-877-289-7664 [Hours]

Boom. SUBTEMBER is here!

Ashly TRA-2075

150W Peak, 2-Channel TRA-Series Power Amplifier w/ Extensive Protection Circuitry

We apologize

This item has been discontinued

Get FAST answers from customers ASK a Question See questions answers

Switchable For Any Job

Ashly's TRA-Series takes all the best parts of the SRA-Series and throws in some even better parts of its own. The TRA-Series incorporates state of the art technological advancements to deliver highly-efficient amplifiers ideal for low impedance, 25V, 70V or 100V installations with moderate power necessities. Four models are available in 2 and 4-channel setups with RMS power ratings of 75W and 150W per channel (@ 4 ohms).

Every control of the TRA-Series amplifiers are either on the rear panel, or they're internal. A 6-step LED meter enables you to monitor the levels for each of the individual channels. Each TRA-Series amplifier can power 4 or 8 ohm loads in addition to constant lines of 70V and 100V simultaneously. The 150W models are amply (no pun intended) capable of directly driving lines of constant 25V using the direct coupled 4 ohm output.

Some of the TRA-Series features include: very low noise, an internally switchable 120V/240V power supply, extensive protection circuitry, euroblock inputs and outputs, main power switch and an LED signal level meter indicating -24dB, -18dB, -12dB, -6dB, -3dB and a clip alert for each channel, level attenuators for the individual channels, rear panel switches to choose between two settings of input sensitivity, remote power turn-on/off and adjustable power-on delay (up to 8 seconds).

All Ashly TRA-Series amplifiers are convection-cooled, which means almost no need for maintenance after initial installation, AND no irritating noise from the fan. With the TRA-Series amplifiers, you get the dependability, ultra-high sonic quality and rugged construction that consumers expect from the Ashly name.

General Features:
  • 150W Peak, 2-Channel Class D Power Amplifier
  • Power Ratings:
    • 8 ohms: 40 watts x 2 chan.
    • 4 ohms: 75 watts x 2 chan.
    • 25/70/100V: 75 watts x 2 chan.
  • Convection cooled so there's no annoying fan noise
  • Switchable 120V/240V power supply (internal)
  • Front panel:
    • Signal level L.E.D.’s on each channel include –24, -18, -12, -6, -3 and clip alert
  • Rear panel:
    • Level attenuators for each channel
    • Euroblock inputs
    • Screw terminal outputs
    • Switches to select between two choices of input sensitivity and HPF frequencies on each channel
    • Remote power turn-on/off and adjustable turn-on delay up to eight seconds.
  • 6-Way protection circuitry (Output over-current, DC output, Main supply rail over voltage, chassis internal temperature, inrush limiting and main fuse)
  • 1-year Manufacturer's warranty
Signal to Noise (20 Hz-20 kHz, unweighted):
TRA-2075 TRA-4075 TRA-2150 TRA-4150
>98 dB >98 dB >105 dB >105 dB

Power Consumption (Pink Noise @ 4 Ohm)
  TRA-2075 TRA-4075 TRA-2150 TRA-4150
1/8th Output 18.75W 37.5W 37.5W 75.0W
1/8th Draw 39.0W 74.0W 64.0W 125W
1/8th Current 0.69A 1.24A 1.10A 1.98A
Idle Power 17.0W 30.0W 20.0W 36.0W
Idle Current 0.30A 0.52A 0.35A 0.62A

Output Circuitry: Class D
Voltage Gain: 26 dB, 36 dB sensitivity (selectable)
Frequency Response: 20 Hz - 20 kHz, +/- 1.0 dB
Damping Factor: - 8 ohm load, < 1 kHz > 200 into 8 ohms
Input Impedance: 20 k ohms, balanced
Maximum Input Level: +21 dBu
Cooling: Convection
Front Panel Indicators per channel: -24dB, -18dB, -12dB, -6dB, -3dB and Clip
Front Panel Indicators: overall power, standby, protect
Attenuators: Per channel rear panel
Input Connectors: each channel 3- Pin Euroblock
Output connectors: each channel Screw terminals
Amplifier Protection: Output Overcurent, DC Output, Main Supply Rail Overvoltage, Chassis Temperature, Inrush Limiting, Mains Fuse

Power Cable Connector: 3-Prong IEC
Dimensions 19” x 3.5” x 11” (All)

Weights TRA-2075 TRA-4075 TRA-2150 TRA-4150
Net 19.5 lbs 29.5 lbs 19.5 lbs 29.5 lbs
Shipping 25.5 lbs 35.5 lbs 25.5 lbs 35.5 lbs

Power Specifications

Number of Channels
This is the number of channels that the professional amplifier is designed to power.
2 Channels
Continuous Power @ 8 ohm
This is the continuous (RMS) power output of the amplifier at an 8 ohm impedance.
40 watts x 2 channels
Continuous Power @ 4 ohm
This is the continuous (RMS) power output of the amplifier at an 4 ohm impedance.
75 watts x 2 channels
Continuous Power @ 8 ohm (Bridged)
This is the continuous (RMS) power output of the amplifier at a bridged 8 ohm impedance.
150 watts x 1 channels
Total Continuous Power
This is the total continuous power rating (RMS) that the amplifier is able to output.
150 watts

Amplifier Specifications

Amplifier Class

An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.

Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.

Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.

Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.

D
Signal-to-Noise Ratio
This spec compares the strength of the signal to the level of background noise. A higher value indicates less background noise.
>98 dB
Frequency Response
The range of frequencies the amplifier will reproduce (lowest frequency to the highest). Bigger is better, meaning the wider the range, the better. The optimal range is 20 - 20,000 Hz (which is the range of human hearing).
20 - 20000 Hz
Input Sensitivity
This is the input sensitivity of the amplifier.
1.4 volts
THD (Total Harmonic Distortion)
The amount of change in harmonic content of the signal as it is amplified. A lower figure indicates less change and a more accurate amp. THD below 0.10% is inaudible.
0.01%
Voltage Gain
This is the voltage gain of the amplifier measured in decibels.
21 dB
Cooling Options
These are the different cooling systems used in the amplifier to keep it cool.
Convection
Inputs
These are the type of input connections that the amplifier has.
Euroblock
Outputs
These are the types of output connections that the amplifier has.
Binding Posts

Physical Specifications

Height
The height of the item, measured from top to bottom, in inches.
3-1/2"
Width
The width of the item from left to right (side-to-side) measured in inches.
19"
Depth
The front-to-rear depth of the item, in inches. If the item is angled or slanted, this value is the bottom measurement.
11"
Weight (Pounds)
This is the weight of the item in pounds (lbs).
19-1/2 lbs
Rackmount Spaces
This is the total number of spaces that the preamplifier will occupy when mounted on a rack.
2U

Specials with this Item

Promotions
Promotions we have offer More Ways to Shop for items that are on clearance, last chance, special offer and sales, Made in America, and more!

Warranty and Return Policy

Parts Warranty Duration
1 year
Labor Warranty Duration
1 year
Warranty Provider
Manufacturer

Summary of Customer Ratings & Reviews

Rating Distribution

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Average Attribution Rating

Durability
0.0
Value
0.0
Features
0.0
Design
0.0
Usability
0.0
Hide answersShow all answers | Sort by
No questions have been asked about this item. Be the first!

Product Summary

Manufacturer

Model Number

TRA-2075

Weight

19.50lbs

Internal SKU

tra2075

Internal Product ID

32368

Sonic Electronix Wiring Guide

Wiring Diagram Legend

Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.

Product Name: Ashly TRA-2075