Massive Audio N2 Ultra-Compact Class-D Monoblock Amplifier w/ 4 AWG OFC Amp Kit
1600W Max (800W RMS) Nano Block Series Class-D Monoblock 1-Ohm Stable Amplifier with Adjustable Bass Boost w/ 100% OFC 4 AWG Amp Wiring Kit
Trending Monoblock Amplifiers
• 300 Watts RMS x 1 @ 4 ohms
• 500 Watts RMS x 1 @ 2 ohms
• Total Peak Power: 1000 Watts
• Speaker Level Input
• Signal Sensing Turn-On
• Variable Low Pass Filter: 50-200 Hz at 24 dB per octave
• Variable Bass Boost: 0 to +18 dB bass boost at 40 Hz
• 550 Watts Peak x 1 @ 4 ohms
• 1100 Watts Peak x 1 @ 2 ohms
• 825 Watts RMS x 1 @ 2 ohms
• Remote Subwoofer Level Control Included
• Pulse Width Modulated MOSFET power supply
• Speaker-level (high-level) inputs
• Signal to Noise Ration: 102 dB
• Frequency Response: 9 - 50,000 Hz
Rockford Fosgate Prime R500X1D
• RMS: 300W x 1 @ 4 ohms, 500W x 1 @ 2 ohms
• Total RMS Power: 500W
• CEA-2006 Compliant
• Remote PLC (Punch Level Control) Included
• Efficient Class-D circuit topology
• Dimensions: 8-1/2"L x 6-3/4"W x 2"H
• RMS: 300W x 1 @ 4 ohms, 500W x 1 @ 2 ohms
• Total Peak Power: 500W
• CEA-2006 Compliant Amplifier
• 4-Channel Speaker-Level Inputs
• Heavy Duty Aluminum Alloy Heat-Sink
• Dimensions: 7-7/8"W x 7-7/8"L x 2-3/16"H
- Description Coming Soon!
Power Specifications - Subwoofer Channel
An amplifier increases the power of the signal being fed to it by taking energy from its power supply and matching the signal but increasing its amplitude. Amplifiers use many different methods for converting these electrical signals and have been categorized into classes.
Class A/B: Greater than 50% of the input signal is amplified while the other percentage is “off”. These amplifiers have a small amount of current flowing through the output transistors all the time which almost eliminates crossover distortion. Class A/B has great sound quality but is not as efficient as class D. These amps are most commonly used to drive speakers.
Class D: Also known as switching amplifiers, class D amps have output transistors that are completely turned “on” or “off”. This means that when the transistors are on, there is almost no voltage across them but when they are off there is significant voltage but no current flowing through it which makes these amplifiers very efficient at the cost of sound quality. These amps are most commonly used to drive subwoofers.Other Classes: You may see classes such as GH, bD, X, FD, etc. by some manufactures. These amplifiers tend to be either class A/B, D or a hybrid of the two but with improvements to their designs that can make them more efficient or offer better sound quality.
It is measured during a brief musical burst, such as a sudden drum accent. Some manufacturers display peak power ratings on the face of their products to increase the appeal.
The RMS power rating is more accurate, and we recommend using it for product comparison.
RMS power is the amount of continuous power, measured in watts, that an amplifier produces is called RMS power. The higher the RMS figure, the louder and cleaner your music sounds.
The RMS output figure is much more accurate than the peak rating when comparing products.
A crossover is a type of filtering system that permits only certain frequencies to play. A Low-Pass (LP) crossover allows only frequencies below its setting to get through which is good in the case of some subwoofers. A High-Pass(HP) filter allows frequencies above its setting to pass through, this is normally used on speakers.
When a crossover is set to FULL it means no filtering is added and the full frequency spectrum is allowed through the amplifier. Filtering is important because feeding a speaker frequencies it cannot reproduce effectively creates distortion.
The steepness of the roll-off slope is measured in dB/octave and refers to the rate of attenuation (lowering of volume) outside their pass bands.
- RMS Power
- Signal-to-Noise Ratio
This rating applies to both external car amplifiers, as well as the amplifiers inside of in-dash stereos.
Amplifier Kit Specifications
Definitions are as follows:
Gauge (wire) - The diameter of a wire. The higher the number, the thinner the wire. Example: 4 gauge wire has more strands than 10 gauge wire.AWG (American Wire Gauge) - A standard of the dimensional characteristics of wire used to conduct electrical current or signals. AWG is identical to the Brown and Sharpe (B & S) wire gauge.
Warranty and Return Policy
Internal Product ID
Wiring Diagram Legend
Warning: The image depicted shows the resistance change when wiring multiple subwoofer terminals. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Sonic Electronix, Inc. is not responsible for damage caused to your audio system or vehicle due to improper installation. Please call tech support at 1-877-289-7664 if you require additional assistance.