Distribution Blocks: Power & Ground Distribution Blocks

Distribution Blocks

Filters
Loading...
Filters

We are sorry, no available results!

This specifies what the intended use of the distribution block is. Fused distribution blocks are intended to be used with the power wire and the fuse acts as a short-circuit or surge protection so your amplifier is not as likely to be damaged. Non-fused distribution blocks can used with ground or power wire connections, but the protection on power wire connections will not be present as there is no fuse in the distribution block. Therefore, we recommend your amplifier has an external fuse for short-circuit or surge protection. When using either type of distribution block, it is recommended to use a main fuse holder within 18 inches of the battery.
For accessories, this is the type of fuse that is required for the item to work properly.

For fuses, this is the type of fuse.

This is the number of fuses that the item requires to work properly.
This is the total number of input connections that go into the unit.
This is the largest gauge wire that will fit into the power and ground terminals of this device. The lower the gauge number, the thicker the wire is. For example, a 4 gauge wire is thicker than an 8 gauge wire and thus has higher current carrying capacity. Always do your best to get this size wire to reduce the risk of damage to your components.
This is the total number of output connections that the unit will produce.
This number refers to the maximum size of wire that will fit into the output connector(s) of the capacitor, battery terminal, or any other connector with an wire output.
listview icon
gridview icon
Stinger SHD20

Stinger SHD20 HPM Series Power or Ground Distribution Block with Satin Chrome Finish

SHD20 main
Go to item page

Stinger SHD20 HPM Series Power or Ground Distribution Block with Satin Chrome Finish

HPM Series Power or Ground Distribution Block • One 1/0 Gauge or 4 Gauge Input • Two 4/8 Gauge Outputs • Protective Cover Included • Corrosion Resistant Satin Chrome Finish

23
Stinger SHD20

Stinger SHD20 HPM Series Power or Ground Distribution Block with Satin Chrome Finish

In stock

$35.99 (63.91% off)
$12.99
Stinger SPD512 (ShocKrome)

PRO Series Power Distribution T-Block with Three 1/0 Gauge Inputs

SPD512 main
Go to item page

PRO Series Power Distribution T-Block with Three 1/0 Gauge Inputs

• PRO Series Power Distribution T-Block
• Three 1/0 Gauge Inputs/Outputs
• Daisy Chain Design
• Deep Wire Recesses
• Oversized Set Screws
• Corrosion Resistant ShocKrome-Plated
• Protective Cover Included

10
Stinger SPD512 (ShocKrome)

PRO Series Power Distribution T-Block with Three 1/0 Gauge Inputs

In stock

$39.99 (75.02% off)
$9.99
Stinger SHD21

HPM Series Power or Ground Distribution Block with Satin Chrome Finish

SHD21 main
Go to item page

HPM Series Power or Ground Distribution Block with Satin Chrome Finish

• HPM Series Power or Ground Distribution Block
• Two 1/0 Gauge or 4 Gauge Inputs
• Four 4/8 Gauge Outputs
• Multiple Input/Output Design
• Protective Cover Included
• Corrosion Resistant Satin Chrome Finish

35
Stinger SHD21

HPM Series Power or Ground Distribution Block with Satin Chrome Finish

In stock

$42.99 (62.81% off)
$15.99
NVX XFDBU2

2 Position Fused Distribution Block with One 0/1 Gauge Input and two 4/8 Gauge Outputs

XFDBU2 main
Go to item page

2 Position Fused Distribution Block with One 0/1 Gauge Input and two 4/8 Gauge Outputs

• One 1/0 Gauge Input
• Two 4 Gauge or 8 Gauge Output
• Satin Chrome Plated Terminals
• All Brass Hardware

25
NVX XFDBU2

2 Position Fused Distribution Block with One 0/1 Gauge Input and two 4/8 Gauge Outputs

In stock

 
$19.99

Item Added to Cart

XFDBU2 small

2 Position Fused Distribution Block with One 0/1 Gauge Input and two 4/8 Gauge Outputs

$19.99

Keep Shopping

T-Spec V8-MANL40

V8 Series 40A Nickel Plated MANL Fuses

$3.00

Add

Don't see the accessory you're looking for?
View all available accessories for the NVX XFDBU2.
Rockford Fosgate RFD4 Distribution Block

One 0 - 4 Gauge Input to Three 4 - 8 Gauge Output Solid Brass Distribution Block

RFD4 main
Go to item page

One 0 - 4 Gauge Input to Three 4 - 8 Gauge Output Solid Brass Distribution Block

• One 1/0 AWG Input with 4 AWG Adapter/Reducer
• Three 4 AWG Outputs with 8 AWG Adapter/Reducer
• Can be used for Power or Ground connections
• Pre-drilled mounting holes for easy installation
• Custom tooled 100% solid brass
• HPP plating for superior corrosion resistance
• Flexible for use with multiple wire sizes
• Connect up to Three Amplifiers from one power source
• Smoked heat-resistant RockfordFosgate cover
• Platinum finish

7
Rockford Fosgate RFD4 Distribution Block

One 0 - 4 Gauge Input to Three 4 - 8 Gauge Output Solid Brass Distribution Block

In stock

$38.99 (23.08% off)
$29.99
JL Audio XD-FDBU-2

MAXI Fuse Power Distribution Block with One 1/0 Gauge Input and Two 4 Gauge Outputs

XD-FDBU-2 main
Go to item page

MAXI Fuse Power Distribution Block with One 1/0 Gauge Input and Two 4 Gauge Outputs

Premium Series Distribution Block • MAXI Fuses • 1/0 or 4 AWG Input • 4 or 8 AWG Outputs • Nickel Plated • Includes Grommets and Wrenches

11
JL Audio XD-FDBU-2

MAXI Fuse Power Distribution Block with One 1/0 Gauge Input and Two 4 Gauge Outputs

In stock

 
Vip Icon $34.99

Item Added to Cart

XD-FDBU-2 small

MAXI Fuse Power Distribution Block with One 1/0 Gauge Input and Two 4 Gauge Outputs

$34.99

Keep Shopping

Stinger SPF5630

30 Amp Maxi Fuses (3-Pack)

$14.99

Add

Don't see the accessory you're looking for?
View all available accessories for the JL Audio XD-FDBU-2.
SMD Single Distribution Block

Power/ Ground Distribution Block (Half Block)

SMD-SINGLE-DISTRIBUTION-BLOCK-SHORT main
Go to item page

Power/ Ground Distribution Block (Half Block)

• Easy-to-use bus/bar distribution block
• 6 Ring Terminal Connections
• Use when installing multiple amps
• 3/4" PVC body
• 1/4" aluminum bus bar
• 3/16" Clear acrylic cover
• Use as a grounding block or positive distribution

1
SMD Single Distribution Block

Power/ Ground Distribution Block (Half Block)

In stock

 
$39.99
JL Audio XD-FDBU-4

4-Way MAXI Fused Distribution Block

XD-FDBU-4 main
Go to item page

4-Way MAXI Fused Distribution Block

• One 1/0 - 4 AWG Input
• Four 4 - 8 AWG Outputs
• Forged and machined brass construction
• Marine-grade stannum plating
• High-temperature polycarbonate base

JL Audio XD-FDBU-4

4-Way MAXI Fused Distribution Block

In stock

Only 2 Left!

 
Vip Icon $44.99

Item Added to Cart

XD-FDBU-4 small

4-Way MAXI Fused Distribution Block

$44.99

Keep Shopping

Stinger SPF5630

30 Amp Maxi Fuses (3-Pack)

$14.99

Add

Don't see the accessory you're looking for?
View all available accessories for the JL Audio XD-FDBU-4.
Stinger SPD5623

PRO Series Maxi Fused Power Distribution Block with Two 1/0 Gauge Inputs and Four 4/8 Gauge Outputs

SPD5623 main
Go to item page

PRO Series Maxi Fused Power Distribution Block with Two 1/0 Gauge Inputs and Four 4/8 Gauge Outputs

• PRO Series Maxi Fuse Power Distribution Block
• Two 1/0 Gauge Inputs
• Four 4/8 Gauge Outputs
• High Power MAXI Fuse Protection
• Deep Wire Recesses
• High Quality ShocKrome Plating
• Snap-Off Cover

11
Stinger SPD5623

PRO Series Maxi Fused Power Distribution Block with Two 1/0 Gauge Inputs and Four 4/8 Gauge Outputs

In stock

$66.99 (61.20% off)
$25.99

Item Added to Cart

SPD5623 small

PRO Series Maxi Fused Power Distribution Block with Two 1/0 Gauge Inputs and Four 4/8 Gauge Outputs

$25.99

Keep Shopping

Stinger SPF5630

30 Amp Maxi Fuses (3-Pack)

$14.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Stinger SPD5623.
Stinger SPD5210

Dual ANL Fused Distribution Block with One 1/0G Input and Two 4G Outputs

SPD5210 main
Go to item page

Dual ANL Fused Distribution Block with One 1/0G Input and Two 4G Outputs

• Dual ANL Fused Distribution Block
• One 1/0 Gauge inputs
• Two 4 Gauge outputs
• Shoc-Krome plating
• Protective cover included

Stinger SPD5210

Dual ANL Fused Distribution Block with One 1/0G Input and Two 4G Outputs

In stock

$63.99 (53.13% off)
$29.99

Item Added to Cart

SPD5210 small

Dual ANL Fused Distribution Block with One 1/0G Input and Two 4G Outputs

$29.99

Keep Shopping

T-Spec V8-ANL80

V8 Series 80A Nickel Plated ANL Fuses

$6.99

Add

Don't see the accessory you're looking for?
View all available accessories for the Stinger SPD5210.
Stinger SPD510

PRO Series Power Distribution T-Block with Three 8 Gauge Inputs

SPD510 main
Go to item page

PRO Series Power Distribution T-Block with Three 8 Gauge Inputs

• PRO Series Power Distribution T-Block
• Three 8 Gauge Inputs/Outputs
• Daisy Chain Design
• Deep Wire Recesses
• Oversized Set Screws
• Corrosion Resistant ShocKrome-Plated
• Protective Cover Included

2
Stinger SPD510

PRO Series Power Distribution T-Block with Three 8 Gauge Inputs

In stock

$25.99 (61.56% off)
$9.99
SMD Split Distribution Block

Power/ Ground Distribution Block (Split Block)

SMD-DISTRIBUTION-BLOCK-SPLIT main
Go to item page

Power/ Ground Distribution Block (Split Block)

• Easy-to-use bus/bar distribution block
• 12 Ring Terminal Connections
• Use when installing multiple amps
• 3/4" PVC body
• 1/4" aluminum bus bar
• 3/16" Clear acrylic cover
• Use as a grounding block or positive distribution

1
SMD Split Distribution Block

Power/ Ground Distribution Block (Split Block)

In stock

$109.48 (33.33% off)
$72.99
Stinger SSDB024

AGU Distribution Block (1)1/0 Ga Input (2) 4 Ga Output

SSDB024 main
Go to item page

AGU Distribution Block (1)1/0 Ga Input (2) 4 Ga Output

• Stinger Select Series
• 100% Brass Satin Finish
• Large Set Screws

Stinger SSDB024

AGU Distribution Block (1)1/0 Ga Input (2) 4 Ga Output

In stock

$25.99 (54.02% off)
$11.95
Stinger SPD513

PRO Series Power or Ground Distribution Block with ShocKrome Finish

SPD513 main
Go to item page

PRO Series Power or Ground Distribution Block with ShocKrome Finish

PRO Series Power or Ground Distribution Block • Two 4/8 Gauge Inputs • Four 8 Gauge Outputs • Multiple Input/Output Design • Protective Cover Included • Corrosion Resistant ShocKrome Finish

7
Stinger SPD513

PRO Series Power or Ground Distribution Block with ShocKrome Finish

In stock

$31.95 (65.60% off)
$10.99
Shuriken SK-TML-BLK

Brass Bus Bar Block with Gate Lock Technology

SK-TML-BLK main
Go to item page

Brass Bus Bar Block with Gate Lock Technology

• Standard 5mm Screw Heads
• Included inserts for Positive and Negative terminal
• Accepts up to 0 gauge ring terminals
• 6 mounting Points
• 100 percent brass
• Easy mount

Shuriken SK-TML-BLK

Brass Bus Bar Block with Gate Lock Technology

In stock

$39.99 (37.51% off)
$24.99
Kicker 46DB4 (DB4)

Distribution Block with Two 1/0-8 Gauge Inputs and Four 4-8 Gauge Outputs

46DB4 main
Go to item page

Distribution Block with Two 1/0-8 Gauge Inputs and Four 4-8 Gauge Outputs

• Brass Construction
• (2) 1/0-8 Gauge In
• (4) 4-8 Gauge Out
• Uses Strong 5mm Screws

Kicker 46DB4 (DB4)

Distribution Block with Two 1/0-8 Gauge Inputs and Four 4-8 Gauge Outputs

In stock

Only 1 Left!

$34.95 (14.19% off)
Vip Icon $29.99
T-Spec V-DIST-PWR

Battery Terminal 3 Position Distribution Block

V-DIST-PWR main
Go to item page

Battery Terminal 3 Position Distribution Block

• Independently MANL fused outputs
• (1) 1/0 AWG - 8 AWG In
• (3) 4 AWG - 10 AWG Out
• Nickel finish for durability
• Compact design for simpler installation
• Solid brass construction for maximum conductivity

1
T-Spec V-DIST-PWR

Battery Terminal 3 Position Distribution Block

In stock

$41.00 (14.63% off)
$35.00

Item Added to Cart

V-DIST-PWR small

Battery Terminal 3 Position Distribution Block

$35.00

Keep Shopping

T-Spec V8-MANL40

V8 Series 40A Nickel Plated MANL Fuses

$3.00

Add

Don't see the accessory you're looking for?
View all available accessories for the T-Spec V-DIST-PWR.
Stinger SPD511

PRO Series Power/Ground Distribution T-Block with Three 4 Gauge Inputs

SPD511 main
Go to item page

PRO Series Power/Ground Distribution T-Block with Three 4 Gauge Inputs

• PRO Series Power Distribution T-Block
• Three 4 Gauge Inputs/Outputs
• Daisy Chain Design
• Deep Wire Recesses
• Oversized Set Screws
• Corrosion Resistant ShocKrome-Plated
• Protective Cover Included

24
Stinger SPD511

PRO Series Power/Ground Distribution T-Block with Three 4 Gauge Inputs

In stock

$28.95 (65.49% off)
$9.99
T-Spec VDB4

1/0- to 4 AWG input, four 4/8 AWG outputs 4 Position Distribution Block

VDB4 main
Go to item page

1/0- to 4 AWG input, four 4/8 AWG outputs 4 Position Distribution Block

• Water-resistant
• (1) 1/0-4 AWG inputs
• (4) 4/8 AWG outputs
• Gate lock technology

T-Spec VDB4

1/0- to 4 AWG input, four 4/8 AWG outputs 4 Position Distribution Block

In stock

 
$26.00
Rockford Fosgate RFFDAGU

Fused AGU Distribution Block with 1/0 AWG or 4 AWG inputs and 4 AWG or 8 AWG outputs

RFFDAGU main
Go to item page

Fused AGU Distribution Block with 1/0 AWG or 4 AWG inputs and 4 AWG or 8 AWG outputs

Platinum plated AGU style fused distribution, flexibility of multiple wire size inputs and outputs. Allows for 2 AGU style fuses. Accept 1/0 AWG and 4 AWG inputs. (2) 4 AWG/8 AWG outputs.

Rockford Fosgate RFFDAGU

Fused AGU Distribution Block with 1/0 AWG or 4 AWG inputs and 4 AWG or 8 AWG outputs

In stock

$53.99 (16.67% off)
$44.99

Item Added to Cart

RFFDAGU small

Fused AGU Distribution Block with 1/0 AWG or 4 AWG inputs and 4 AWG or 8 AWG outputs

$44.99

Keep Shopping

T-Spec V8-AGU40

V8 Series 40A Nickel Plated AGU Fuses

$5.00

Add

Don't see the accessory you're looking for?
View all available accessories for the Rockford Fosgate RFFDAGU.

Items per page: 20 50 100

Distribution blocks are a vital accessory to your vehicles aftermarket audio system. The basic idea behind a car audio distribution block is to take a power input and split the power through multiple cables. Fused distribution blocks can serve to protect your audio components from unwanted power surges and are designed for power cables. Non-fused distribution blocks are ideal for ground wires and can be an excellent way to join several ground cables.

Our wide collection power (fused) and ground (non-fused) distribution blocks can be found here. No matter how many cables, amplifiers, speakers, subwoofer, or other component you have for your car, we will have the distribution blocks that you need!
    clear all items